• 한국자동차공학회논문집
• /
• 제16권6호
• /
• pp.58-64
• /
• 2008

An aluminum radius rod using rheo-forging method has been developed for heavy commercial vehicles to decrease vehicle unsprung weight. To design the shape of the rod, structural simulations are performed using two load cases. To evaluate durability performance of the rods, a test system which has simultaneous 3 axes actuating system is developed. And 3 axes durability test conditions are established based on vehicle field tests. Using the test systems and the conditions, the durability test is carried out and the rods have passed the test conditions of 700,000 cycles. The weight of a developed aluminum radius rod is 4.2kg and it was drastically reduced by 48.8 percent in comparison with the weight of a steel radius rod.

• Design & Manufacturing
• /
• 제2권2호
• /
• pp.43-47
• /
• 2008

This paper is concerned with the analysis of material flow characteristics of stepped rod forming. The analysis in this paper concentrated on the evaluation of the design parameters for deformation patterns of tube forming, load characteristics, extruded length, and die pressure. The design factors such as punch nose radius, die corner radius, friction factor, and punch face angle are involved in the simulation. The stepped rod forming is analyzed by using a commercial finite element code. This simulation makes use of stepped rod material and punch geometry on the basis of punch geometry recommended by International Cold Forging Group. As radius ratio is large, forming load was reduced but extruded length ratio was increased.

• 대한기계학회논문집
• /
• 제19권2호
• /
• pp.382-390
• /
• 1995

Failure of connecting rod in automotive engine may cause catastrophic situation. The corner radius at small end has an effect on stress raising. To investigate the stress distribution in connecting rod during operation, the finite element analysis was used by giving possible maximum tension and compression. Excessive sizing after forging connecting rod may result in the tensile residual stress which lower the fatigue life and cause premature failures. It was shown that when the sizing amount is too large, the location of high tensile residual stress coincide with that of high stress amplitude during operation through the elastic-plastic finite element analysis. The endurance limit moves down due to the surface finish and decarburization, which combines with the movement of resultant stress points to dangerous range. It was concluded that the precise control of sizing and enough corner radius are necessary to a reliability of connecting rod.

• 한국자동차공학회논문집
• /
• 제22권1호
• /
• pp.29-35
• /
• 2014

This paper aims to obtain the effect of lightweight on Radius rod. The response surface method used in the paper is the statistical method. Optimization method is performed with the Radius rod using the lightweight material. Structural analysis is executed by using the ANSYS program to find static and dynamic responses. From this study result, it is verified that the response surface method has the advantage of optimum value in comparison with other optimization methods. The analysis is also performed by response surface method to derive optimal design values. Steel model and aluminium initial model are obtained by finite element analysis to clarify design criteria and the results are compared with three models each other. The weights can be reduced by optimal design analysis results of these models similar to those of existing products. The quantitative goals in this study can also attained through results of fatigue analyses. The reliability on optimal design of Radius rod can be improved by use of structural and fatigue analysis results.

• Nuclear Engineering and Technology
• /
• 제52권12호
• /
• pp.2880-2886
• /
• 2020

A small leak occurring on the surface of a fuel rod due to damage exposes UO₂ to a steam atmosphere. During this time, fission gas trapped inside the fuel rod leaks out, and the gas leakage can be increased due to UO₂ oxidation. Numerous studies have focused on the steam oxidation and its thermodynamic calculation in UO₂. However, the thermodynamic calculation of the UO₂ oxidation in a pressurized water reactor (PWR) environment has not been studied extensively. Moreover, the kinetics of the oxidation of UO₂ pellet also has not been investigated. Therefore, in this study, the thermodynamics of UO₂ oxidation under steam injection due to a damaged fuel rod in a PWR environment is studied. In addition, the diminishing radius of the UO₂ pellet with time in the PWR environment was calculated through an experiment simulating the initial time of steam injection at the puncture.

• 소성∙가공
• /
• 제8권4호
• /
• pp.331-339
• /
• 1999

In this study, to analyze the shaped drawing process from round bar, the practical conical die with considering die radius and bearing was defined by a mathematical expression, and also a simple technique for initial mesh generation to the shaped drawing process was proposed. The drawing of rectangular section from round bar, one of the shaped drawing process, has been simulated by using non-steady state 3D rigid plastic finite element method in order to evaluate the influence of semi-die angle and reduction in area to corner filling. Other process variables such as friction constant, rectangular ratio, die radius and bearing length were fixed during the simulation. An artificial neural network has been introduced to obtain the optimal process conditions which gave rise to a fast simulation.

• Journal of electromagnetic engineering and science
• /
• 제5권2호
• /
• pp.72-79
• /
• 2005

The leaky dispersion characteristics of a circular dielectric rod were investigated using Davidenko's method for several lower-order transverse magnetic(TM) modes. The normalized complex propagation constants were precisely determined and their tolerances below $10^{-10}$ compared with zero for both real and imaginary parts. It was also checked whether the normalized complex propagation constants obtained represented forward leaky waves. The leaky modes existing below the cutoff frequency of the guided mode were classified as a nonphysical mode, reactive mode, antenna mode, and spectral gap based on a precise determination of the complex propagation constants. Finally, the effects of the dielectric constant and radius of the dielectric rod on the leaky dispersion characteristics were also considered.

• International Journal of Precision Engineering and Manufacturing
• /
• 제2권1호
• /
• pp.87-93
• /
• 2001

A reliable analytic model that determines the exit cross sectional shape a workpiece(material) in round-oval (oroval-round) pass sequence has been developed. The exit cross sectional shape of an outgoing workpiece is predicted by using the linear interpolation of the radius of curvature of an incoming workpiece and that of roll groovw to the roll axis direction. The requirements placed on the choice of the weighting function were to ensure boundary conditions specified. The validity of the analytic model has been examined by not rod rolling experiment with the roll gap and specimen size changed. The exit cross sectional shape and area of the workpiece predicted by the proposed analytic model were good agreement with those obtained experimentally. We found that the analytic model has not only simplicity and accuracy for practical usage but also save a large amount of computational time compared with finite element method.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2002년도 종합학술발표회 논문집 Vol.12 No.1
• /
• pp.356-360
• /
• 2002

Leaky modes on a circular dielectric rod are investigated from the precisely determined normalized complex propagation constants using Davidenko's complex root finding technique. Below the cutoff frequency of the guided mode, distinct frequency regions that have unique properties are observed, such as nonphysical region, antenna mode region, reactive mode region, and spectral gap region. The effects of tro design parameters, dielectric constants and the radius of the rod, to the leaky mode characteristics are also considered.

• 한국정밀공학회지
• /
• 제17권9호
• /
• pp.174-180
• /
• 2000

A reliable analytic model that determines the cross sectional shape of a workpiece(material) in round-oval(or oval-round) pass sequence has been developed. the cross sectional shape of an outgoing workpiece is predicted by using the linear interpolation of the radius of curvature of an incoming workpiece and that of roll groove to the roll axis direction. The requirements we placed on the choice of the weighting function were to ensure boundary conditions specified. The validity of the analytic model has been examined by hot rod rolling experiment with the roll gap and specimen size changed. The cross sectional shape and area of a workpiece predicted by the proposed analytic model were good agreement with those obtained experimentally. It was found that the analytic model has not only simplicity and accuracy for practical usage but also save a large amount of computational time compared with finite element method.