• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.6
• /
• pp.438-444
• /
• 2019

In this paper, we proposed a 16-element array antenna design to improve signal detection performances. The array antenna characteristics, such as mutual coupling, pattern deviation, and half power beamwidth of the active element, were examined to obtain an optimal spacing between individual elements. The single element of the array antenna consists of an indirect feed using L-shaped feed and shorted radiating patch to achieve a broadband operation. Root mean square(RMS) errors based on the incident angle of the signal were calculated to verify the signal detection performance of the proposed antenna. The results demonstrate that the proposed array antenna with optimal spacing is suitable for detecting interference signals with low RMS error.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.6C
• /
• pp.343-348
• /
• 2011

This paper introduces a design for real time wireless headset using ANC (active noise control) system based on NFxLMS adaptive filter algorithm. The training time of the proposed system is significantly reduced by using the RMS delay spread of a channel as an error correction parameter, and convergence rate of the FxLMS filter has been improved with updating the coefficients of the NFxLMS filter, which we have got during the training process. Our system has shorter training time and better convergence rate at the same noise reduction level than the conventional system under real noisy environment.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.6A
• /
• pp.1099-1106
• /
• 2001

본 논문에서는 IEEE 802.11a 표준안으로 확정된 OFDM(Orthogonal Frequency Division Multiplexing) 방식을 적용한 고속 무선 LAN의 최적 시스템을 설계하기 위하여 실내 채널 특성들을 분석하였다. 통계적 채널 모델링 및 JTC(Joint Technical Committee) 모델에서의 실내 및 실외 환경을 선택하여 채널에 따른 고속 무선 LAN 시스템을 모의 실험하였다. 또한 채널에 의한 열화를 보상하기 위하여 무선 LAN 표준안에 따른 긴 훈련 신호를 이용한 채널 등화기법인 LS(Least Square) 방식과 LMMSE(Linear Minimum Mean Square Error) 방식을 비교 분석하였다. LS 기법과 본 논문에서 제시한 LS 방식으로 채널의 지연 확산 rms(root mean square) 값을 추정한 후 LMMSE 기법을 사용한 경우의 차이점을 고찰하였다. 이러한 LMMSE 기법을 채택할 경우 LS 기법에 비해 실외환경과 같은 열악한 채널환경 하에서도 시스템 성능에 상당한 개선효과가 나타남을 확인할 수 있었다.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.57 no.4
• /
• pp.377-382
• /
• 2008

For stator winding protection of AC generator, KCL(Kirchhoff's Current Law) is widely applied. Actually a CRDR(Current Ratio Differential Relay) based on DFT(Discrete Fourier Transform) has been used for protecting generator. It has been pointed out that defects can occur during the process of transforming a time domain signal into a frequency domain one which can lead to loss of time domain information. Wavelets techniques are proposed for the analysis of power system transients. This paper introduces an algorithm to choose a suitable Mother Wave1et for generator stator fault detection. For optimal selection, we analyzed db(Daubechies), sym(Symlets), and coif(Coiflects) of Mother Wavelet. And we compared with performance of the choice algorithm using detail coefficients energy and RMS(root mean square) error. It can be improved the reliability of the conventional DFT based CRDR. The feasibility and effectiveness of the proposed scheme is proved with simulation using collected data obtained from ATP (Alternative Transient Program) package.

• Journal of Korea Multimedia Society
• /
• v.8 no.12
• /
• pp.1565-1571
• /
• 2005

Images reconstructed with Maximum-Likelihood Expectation-Maximization (MLEM) algorithm have been observed to have checkerboard effects and have noise artifacts near edges as iterations proceed. To compensate this ill-posed nature, numerous penalized maximum-likelihood methods have been proposed. We suggest a simple algorithm of applying edge detecting process to the MLEM and Bayesian Expectation-Maximization (BEM) to reduce the noise artifacts near edges and remove checkerboard effects. We have shown by simulation that this algorithm removes checkerboard effects and improves the clarity of the reconstructed image and has good properties based on root mean square error (RMS).

• ETRI Journal
• /
• v.25 no.1
• /
• pp.19-24
• /
• 2003

This paper describes the performance of a Ku-band 5-bit monolithic phase shifter with metal semiconductor field effect transistor (MESFET) switches and the implementation of a ceramic packaged phase shifter for phase array antennas. Using compensation resistors reduced the insertion loss variation of the phase shifter. Measurement of the 5-bit phase shifter with a monolithic microwave integrated circuit demonstrated a phase error of less than $7.5{\circ}$ root-mean-square (RMS) and an insertion loss variation of less than 0.9 dB RMS for 13 to 15 GHz. For all 32 states of the developed 5-bit phase shifter, the insertion losses were $8.2{\pm}1.4$dB, the input return losses were higher than 7.7 dB, and the output return losses were higher than 6.8 dB for 13 to 15 GHz. The chip size of the 5- bit monolithic phase shifter with a digital circuit for controlling all five bits was 2.35 mm ${\times}$1.65 mm. The packaged phase shifter demonstrated a phase error of less than $11.3{\circ}$ RMS, measured insertion losses of 12.2 ${\pm}$2.2 dB, and an insertion loss variation of 1.0 dB RMS for 13 to 15 GHz. For all 32 states, the input return losses were higher than 5.0 dB and the output return losses were higher than 6.2 dB for 13 to 15 GHz. The size of the packaged phase shifter was 7.20 mm${\times}$ 6.20 mm.

• ETRI Journal
• /
• v.35 no.4
• /
• pp.638-643
• /
• 2013

This paper presents a 5-bit digital step attenuator (DSA) using a commercial 0.18-${\mu}m$ silicon-on-insulator (SOI) process for the wideband phased array antenna. Both low insertion loss and low root mean square (RMS) phase error and amplitude error are achieved employing two attenuation topologies of the switched path attenuator and the switched T-type attenuator. The attenuation coverage of 31 dB with a least significant bit of 1 dB is achieved at DC to 20 GHz. The RMS phase error and amplitude error are less than $2.5^{\circ}$ and less than 0.5 dB, respectively. The measured insertion loss of the reference state is less than 5.5 dB at 10 GHz. The input return loss and output return loss are each less than 12 dB at DC to 20 GHz. The current consumption is nearly zero with a voltage supply of 1.8 V. The chip size is $0.93mm{\times}0.68mm$, including pads. To the best of the authors' knowledge, this is the first demonstration of a low phase error DC-to-20-GHz SOI DSA.

• The Bulletin of The Korean Astronomical Society
• /
• v.35 no.2
• /
• pp.51.2-51.2
• /
• 2010

We have investigated 63 intense geomagnetic storms (Dst $\leq$ -100 nT) that occurred from 1998 to 2006. Using these events, we compared Dst forecast models: Burton et al. (1975), Fenrich and Luhmann (1998), O'Brien and McPherron (2000a), Wang et al. (2003), and Temerin and Li (2002, 2006) models. For comparison, we examined a linear correlation coefficient, RMS error, the difference of Dst minimum value (${\Delta}$peak), and the difference of Dst minimum time (${\Delta}$peak_time) between the observed and the predicted during geomagnetic storm period. As a result, we found that Temerin and Li model is mostly much better than other models. The model produces a linear correlation coefficient of 0.94, a RMS (Root Mean Square) error of 14.89 nT, a MAD (Mean Absolute Deviation) of ${\Delta}$peak of 12.54 nT, and a MAD of ${\Delta}$peak_time of 1.44 hour. Also, we classified storm events as five groups according to their interplanetary origin structures: 17 sMC events (IP shock and MC), 18 SH events (sheath field), 10 SH+MC events (Sheath field and MC), 8 CIR events, and 10 nonMC events (non-MC type ICME). We found that Temerin and Li model is also best for all structures. The RMS error and MAD of ${\Delta}$peak of their model depend on their associated interplanetary structures like; 19.1 nT and 16.7 nT for sMC, 12.5 nT and 7.8 nT for SH, 17.6 nT and 15.8 nT for SH+MC, 11.8 nT and 8.6 nT for CIR, and 11.9 nT and 10.5 nT for nonMC. One interesting thing is that MC-associated storms produce larger errors than the other-associated ones. Especially, the values of RMS error and MAD of ${\Delta}$peak of SH structure of Temerin and Li model are very lower than those of other models.

• Journal of Positioning, Navigation, and Timing
• /
• v.9 no.3
• /
• pp.221-227
• /
• 2020

In this paper, the Iterated Consider Extended Kalman Filter (ICEKF) is proposed for bearing-only localization of GNSS interference to improve the estimation performance and filter consistency. The ICEKF is an extended version of Consider KF (CKF) for Iterated EKF (IEKF) to consider an effect of bearing measurement bias error to filter covariance. The ICEKF can mitigate the EKF divergence problem which can occur when linearizing the nonlinear bearing measurement by a large initial state error. Also, it can mitigate filter inconsistency problem of EKF and IEKF which can occur when a weakly observable bearing measurement bias error state is not included in filter state vector. The simulation result shows that the localization error of the ICEKF is smaller than the EKF and IEKF, and the Root Mean Square (RMS) estimation error of ICEKF matches the covariance of filter.

• Journal of Positioning, Navigation, and Timing
• /
• v.2 no.2
• /
• pp.131-137
• /
• 2013

In this study, positioning results that combined the code observation information of GPS and GLONASS navigation satellites were analyzed. Especially, the distribution of GLONASS satellites observed in Korea and the combined GPS/GLONASS positioning results were presented. The GNSS data received at two reference stations (GRAS in Europe and KOHG in Goheung, Korea) during a day were processed, and the mean value and root mean square (RMS) value of the position error were calculated. The analysis results indicated that the combined GPS/GLONASS positioning did not show significantly improved performance compared to the GPS-only positioning. This could be due to the inter-system hardware bias for GPS/GLONASS receivers, the selection of transformation parameters between reference coordinate systems, the selection of a confidence level for error analysis, or the number of visible satellites at a specific time.