• JSTS:Journal of Semiconductor Technology and Science
• /
• v.5 no.2
• /
• pp.113-119
• /
• 2005

4H-SiC planar MESFETs were fabricated using ion-implantation on semi-insulating substrate without recess gate etching. A modified RCA method was used to clean the substrate before each procedure. A thin, thermal oxide layer was grown to passivate the surface and then a thick field oxide was deposited by CVD. The fabricated MESFET showed good contact properties and DC/RF performances. The maximum oscillation frequency of 34 GHz and the cut-off frequency of 9.3 GHz were obtained. The power gain was 10.1 dB and the output power of 1.4 W was obtained for 1 mm-gate length device at 2 GHz. The fabricated MESFETs showed the charge trapping-free characteristics and were characterized by the extracted small-signal equivalent circuit parameters.

• KSTLE International Journal
• /
• v.3 no.1
• /
• pp.38-42
• /
• 2002

Diamond-like Carbon(DLC) films were deposited on Si wafers by an RF-plasma-assisted CVD using CH$_4$gas. Tribological tests were conducted with the use of a rotating type ball on a disk friction tester with dry air. This study made use of four kinds of mating balls that were made with stainless steel but subjected to different annealing conditions in order to achieve different levels of hardness. In all load conditions, testing results demonstrated that the harder the mating materials, the lower the friction coefficient was. The friction coefficients were fecund to be lower with austenite mating balls than with fully annealed martensite balls. Conversely, the high friction coefficient found in soft martensite balls appeared to be caused by the larger contact area between the DLC film and the ball. The wear tracks on DLC films and mating balls could prove that effect. Measuring the wear track of both DLC films and mating balls revealed a similar tendency compared to the results of friction coefficients. The wear rate of austenite balls was also less than that of fully annealed martensite balls. Friction eoefficients decrease when applied leads exceed critical amount. The wear track on mating balls showed that a certain amount of material transfer occurs from the DLC film to the mating ball during a high friction process. Raman Spectra analysis Showed that the transferred materials were a kind of graphite and that the contact surface of the DLC film seemed to undergo a phase transition from carbon to graphite during the high friction process.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.105-105
• /
• 1999

차세대 기억소자에서는 집접도의 증가, 고속화, 그리고 미세화에 따라 배선간으 최소선폭이 작아지고, 새로운 다층 배선기술이 요구되는 가운데 층간절연막의 재료와 형성기술은 소자의 특성을 향상시켜주는 중요한 요소로서 열적안정성, 저유전율, 평탄화특성 등에 핵심을 두고 연구되고 있다. 본 연구에서는 5인치 p-Si(100) 위에 FTES와 O2를 precursor로 하고 carrier gas를 Ar gas하여 ICP CVD 방법으로 저유전율의 Fluorocarbonated-SiO2 박막을 형성하였다. 0.1-1kW, 13.56MHz인 rf power를 사용하였으며, 증착은 RT에서 5~10분으로 하였다. 형성된 박막은 FTIR(fourier transform infrared), XPS(x-ray photoelectron spectroscopy), 그리고 ellipsopsometer 등을 이용하여 결합모드와 F농도, 균일도 등을 측정하고, I-V와 C-V 측정장치, 그리고 SERM(scanning electrion microscopy) 등을 이용하여 유전상수, 누설전류, dielectric breakdown voltage, 그리고 박막의 stepcoverage를 측정하였다. 제작된 박막의 신뢰성은 열처리에 따른 전기적 특성으로부터 조사하였다. 형성된 fluorocarbonated 박막 결합모드는 Si-F, Si-O, O-C, C-C와 C-F였고 O2:FTES:Ar 유량을 1sccm:10sccm:6sccm으로 하여 증착한 시료에서 유전율은 2.8이었으며, 누설전류밀도는 8$\times$10-9A/cm2, Breakdown voltage는 10MV/cm 이상, 그리고 stepcoverage는 91%로 측정되었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.99-100
• /
• 2005

We have grown carbon nanotubes (CNTs) with a microwave plasma chemical vapor deposition (MPECVD) method, which has been regard as one of the most promising candidates for the synthesis of CNTs due to the vertical alignment, the low temperature and the large area growth. We use methane ($CH_4$) and hydrogen ($H_2$) gas for the growth of CNTs. 60 nm thick Ni catalytic layer were deposited on the TiN coated glass substrate by RF magnetron sputtering method. In this work, we report the effects of pressure on the growth of CNTs. We have changed pressure of processing (10 $\sim$ 20 Torr) deposition of CNTs. SEM (Scanning electron microscopy) images show diameter, length and cross section state CNTs.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.298-299
• /
• 2011

최근 입력소자로 활용되는 터치스크린은 키보드나 마우스와 같은 입력장치를 사용하지 않고, 스크린에 손가락, 펜 등을 접촉하여 입력하는 방식이다. 터치패널의 구현방식에 따라 저항막(Resistive) 방식, 정전용량(Capacitive) 방식, SAW (Surface Accoustic Wave; 초음파) 방식, IR (Infrared; 적외선) 방식등으로 구분된다. 특히 최근 관심을 받고 있는 IR 방식은 적외선이 사람의 눈에는 보이지 않으나, 직진성을 가지고 있어 장애물이 있으면 차단되는 특성을 이용한 방식이다. IR방식의 터치패널은 발광(Light emitting)소자와 수광(Light detecting)소자가 마주하도록 배치되어 터치에 의해 차단된 좌표를 인식하게 되며, ITO 필름 등이 필요 없어 Glass 1장으로도 구현이 가능하며 투과율이 우수하다. 이러한 IR 방식의 터치패널을 제작하기 위하여 사용된 IR 광검출기는 광학적 band-gap이 작은 박막물질을 필요로 한다. 본 연구에서는 IR 광검출을 위한 물질로 SiGe를 co-sputtering 기법을 이용하여 성장시켰다. 일반적으로 SiGe 박막을 성장시키기 위하여 저압화학기상증착법(low pressure chemical vapor deposition, LPCVD)이나 고진공 LPCVD를 사용하지만 본 연구에서는 CVD에 비하여 무독성이면서 환경친화적이고 초기투자비용이 낮은 증착장비인 sputtering을 이용하였다. 본 연구에서 성장된 SiGe 박막은 400$^{\circ}C$에서 rf plasma가 인가된 Ge과 dc plasma가 인가된 Si의 power를 조절하여 결정화도가 70% (Fig. 1)이고 결정성장방향이 (111)과 (220)방향으로 성장하는 SiGe 박막을 얻을 수 있었다. 본 논문에서는 co-sputtering 성장조건에 따라 성장된 SiGe의 박막 특성을 논의할 것이다.

• Korean Journal of Materials Research
• /
• v.7 no.12
• /
• pp.1047-1051
• /
• 1997

CH$_{4}$와 H$_{2}$의 혼합가스에 미량의 질소와 산소를 첨가하여 rf-플라즈마 CVD법으로 DLC막을 합성하였다. 이 때 챔버내 압력은 430mtorr, 기판에 인가된 전력은 80W였으며, H$_{2}$와 CH$_{4}$의 비율은 1:1이었다. 이 시편들에 대해 가시광선 영역과 자외선 영역에서의 투과도를 비교하였으며, 결합구조의 변화를 알아보기 위하여 FTIR 분석을 실시하였다. 질소의 경우 첨가량이 6.3%에서 17.4%으로 증가됨에 따라 전체적인 투과도값이 증가하였으며, FRIR 분석결과 wavenumber 3500 $cm^{-1}$ /의 위치에 N-H stretching band가 나타나고 2300$cm^{-1}$ /에는 nitrile의 피크가 나타났다. 이 피크들의 존재는 질소의 첨가에 의하여 interlink를 감소시킴으로써 막의 잔류응력을 현저히 감소시킬 수 있음을 의미한다. 2% $O_{2}$를 첨가한 경우 막의 투과도는 질소를 첨가한 경우보다 월등히 더 향상되었다. 질소첨가량을 증가시킴에 따라 optical band gap또한 증가되는 경향을 보였으며, 2% $O_{2}$를 첨가하였을 때 막의 optical band gap은 0.5까지 감소하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.582-582
• /
• 2013

Oxide TFT (thin film transistor) active channel layer에 대한 저온 열처리 공정은 투명하고 flexibility을 기반으로하는 display 산업과 AMOLED (active matrix organic light emitting diode) 분야 등 다양한 분야에서 필요로 하는 기술로서 많은 연구가 이루어지고 있다. 과거 active layer는 ALD (atomic layer deposition), CVD (chemical vapor deposition), pulse laser deposition, radio frequency-dc (RF-dc) magnetron sputtering 등과 같은 고가의 진공 장비를 이용하여 증착 되어져 왔으나 현재에는 진공 장비 없이 spin-coating 후 열처리 하는 저가의 공정이 주로 연구되어 지고 있다. Flexible 기판들은 일반적인 OTFT (oxide thin films Transistor)에 적용되는 열처리 온도로 공정 진행시 열에 의한 기판의 손상이 발생한다. Flexible substrate의 열에 의한 기판 손상을 막기 위해 저온 열처리 공정이 연구되고 있지만 기존 열처리와 비교하여 소자의 특성 저하가 동반 되었다. 본 연구에서는 Si 기판위에 SiO2 (100)를 절연층으로 증착하고 그 위에 IZO (indium zinc oxide) solution을 spin-coating 한뒤 $250^{\circ}C$ 이하의 온도에서 열처리하였다. 저온 공정으로 인하여 소자의 특성 저하가 동반 되었으므로 소자의 저하된 특성 복원하고자 post-treatment로 고가의 진공장비가 필요 없고 roll-to roll system 적용이 수월한 remote-type의 APP (atmospheric pressure plasma) 처리를 하였다. Post-treatment로 APP를 이용하여 $250^{\circ}C$ 이하에서 소자에 적용 가능한 on/off ratio를 얻을 수 있었다.

• Journal of the Korean Vacuum Society
• /
• v.8 no.2
• /
• pp.165-171
• /
• 1999

Diamond-like carbon(DLC) films were synthesized using the rf-plasma CVD technique with the addition of small amounts of nitrogen and oxygen to a gas mixture of $CH_4$ and $H_2$. The gas flow ratio of $CH_4$ to $H_2$ was 2.4:1, and 3% , 13.6% of nitrogen were added to the gas mixture of $CH_4$ and $H_2$ for the deposition of DLC films. The film stress tended to decrease as the nitrogen concentration increased from 3% to 13.6%, probably due to the decrease of the number of the interlink between carbon atoms. The residual stress tended to slightly decrease when 3% of oxygen was added. Scratch tests were performed to investigate the adhesion between the DLC films and the Ti intelayer after pretreating the TiN surface with direct hydrogen plasma. The adhesion was enhanced by adding nitrogen and oxygen to the $CH_4$ and $H_2$ gas mixture. The adhesion for the 3% nitrogen addition was better than that for the 13.6% nitrogen addition. The Vicker's hardness of the DLC films was measured to be 1100Hv.

• Proceedings of the KIEE Conference
• /
• 2006.10a
• /
• pp.38-39
• /
• 2006

We present experimental results that regard the effects of catalyst preparation on the structural and field-emissive properties of CNTs. The CNTs used in this research have been synthesized using the inductively coupled plasma-chemical vapor deposition (ICP-CVD) method. Catalyst materials (such as Ni, Co, and Invar 426) are varied and deposited on buffer films by RF magnetron sputtering. Prior to growth of CNTs, $NH_3$ plasma etching has also been performed with varying plasma etching time and power. For all the CNTs grown, nanostructures and morphologies are analyzed using Raman spectroscopy and FESEM, in terms of buffer films, catalyst materials, and pre-treatment conditions. Furthermore, the field electron-emission of CNTs are measured and characterized in terms of the catalyst preparation environments. The CNTs grown on Nicatalyst layer would be more effectual for enhancing the growth rate and achieving the vertical-alignment of CNTs rather than other buffer materials from results of SEM study. The crystalline graphitic structure of CNTs is improved as the catalyst dot reaches a critical size. Also, the field-emission result shows that the CNTs using Ni catalyst would be more favorable for improving electron-emission capabilities of CNTs compared with other samples.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.6
• /
• pp.501-506
• /
• 2006

Carbon nanotubes (CNTs) were grown with a microwave plasma enhanced chemical vapor deposition (MPECVD) method, which has been regarded as one of the most promising candidates for the synthesis of CNTs due to the vertical alignment, the low temperature and the large area growth. MPECVD used methane ($CH_4$) and hydrogen ($H_2$) gas for the growth of CNTs. 10 nm thick Ni catalytic layer were deposited on the Ti coated Si substrate by RF magnetron sputtering method. In this work, the pretreatment was that the Ni catalytic layer in different microwave power (600, 700, and 800 W). After that, CNTs deposited on different pressures (8, 12, 16, and 24 Torr) and grown same microwave power (800 W). SEM (Scanning electron microscopy) images showed Ni catalytic layer diameter and density variations were dependent with their pretreatment conditions. Raman spectroscopy of CNTs shows that $I_D/I_G$ ratios and G-peak positions vary with pretreatment conditions.