• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.5
• /
• pp.397-402
• /
• 2010

In this paper, we studied WVTR(water vapor transmission rate) properties of $Si_3N_4$ thin film that was deposited using TCP-CVD (transformer coupled plasma chemical vapor deposition) method for the possibility of OLED(organic light emitting diode) encapsulation. Considering the conventional OLED processing temperature limit of below $80^{\circ}C$, the $Si_3N_4$ thin films were deposited at room temperature. The $Si_3N_4$ thin films were prepared with the process conditions: $SiH_4$ and $N_2$, as reactive gases; working pressure below 15 mTorr; RF power for TCP below 500 W. Through MOCON test for WVTR, we analyzed water vapor permeation per day. We obtained that WVTR property below 6~0.05 gm/$m^2$/day at process conditions. The best preparation condition for $Si_3N_4$ thin film to get the best WVTR property of 0.05 gm/$m^2$/day were $SiH_4:N_2$ gas flow rate of 10:200 sccm, working pressure of 10 mTorr, working distance of 70 mm, TCP power of 500 W and film thickness of 200 nm. respectively. The proposed results indicates that the $Si_3N_4$ thin film could replace metal or glass as encapsulation for flexible OLED.

• Journal of the Korean institute of surface engineering
• /
• v.47 no.2
• /
• pp.75-80
• /
• 2014

Nanocrystalline diamond(NCD) films on steel(SKH51) has been investigated using SiC interlayer film. SiC was deposited on SKH51 or Si wafer by RF magnetron sputter. NCD was deposited on SiC at $600^{\circ}C$ for 0.5~4 h employing microwave plasma CVD. Film morphology was observed by FESEM and FIB. Film adherence was examined by Rockwell C adhesion test. The growth rate of NCD on SiC/Si substrate was much higher than that on SiC/SKH51. During particle coalescence, NCD growth rate was slow since overall rate was determined by the diffusion of carbon on SiC surface. After completion of particle coalescence, NCD growth became faster with the reaction of carbon on NCD film controlling the whole process. In the case of SiC/SKH51 substrate, a complete NCD film was not formed even after 4 h of deposition. The adhesion test of NCD/SiC/SKH51 samples revealed a delamination of film whereas that of SiC/SKH51 showed a good adhesion. Many voids of less than 0.1 ${\mu}m$ were detected on NCD/SiC interface. These voids were believed as the reason for the poor adhesion between NCD and SiC films. The origin of voids was due to the insufficient coalescence of diamond particles on SiC surface in the early stage of deposition.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.319-319
• /
• 2013

Even though the fabrication methods of metal oxide based thin film capacitor have been well established such as RF sputtering, Sol-gel, metal organic chemical vapor deposition (MOCVD), ion beam assisted deposition (IBAD) and pulsed laser deposition (PLD), an applicable capacitor of printed circuit board (PCB) has not realized yet by these methods. Barium Strontium Titanate (BST) and other high-k ceramic oxides are important materials used in integrated passive devices, multi-chip modules (MCM), high-density interconnect, and chip-scale packaging. Thin film multi-layer technology is strongly demanded for having high capacitance (120 nF/$mm^2$). In this study, we suggest novel multi-layer thin film capacitor design and fabrication technology utilized by plasma assisted deposition and photolithography processes. Ba0.6Sr0.4TiO3 (BST) was used for the dielectric material since it has high dielectric constant and low dielectric loss. 5-layered BST and Pt thin films with multi-layer sandwich structures were formed on Pt/Ti/$SiO_2$/Si substrate by RF-magnetron sputtering and DC-sputtering. Pt electrodes and BST layers were patterned to reveal internal electrodes by photolithography. SiO2 passivation layer was deposited by plasma-enhanced chemical vapor deposition (PE-CVD). The passivation layer plays an important role to prevent short connection between the electrodes. It was patterned to create holes for the connection between internal electrodes and external electrodes by reactive-ion etching (RIE). External contact pads were formed by Pt electrodes. The microstructure and dielectric characteristics of the capacitors were investigated by scanning electron microscopy (SEM) and impedance analyzer, respectively. In conclusion, the 0402 sized thin film multi-layer capacitors have been demonstrated, which have capacitance of 10 nF. They are expected to be used for decoupling purpose and have been fabricated with high yield.

• Journal of the Korean Vacuum Society
• /
• v.6 no.2
• /
• pp.151-158
• /
• 1997

Nitrogen incorporated diamond-like carbon films were deposited by r.f. glow discharge of mixtures of benzene and ammonia gases. Mechanical properties, composition and atomic bond structure were investigated when the fraction of ammonia increases from 0 to 0.79 and the negative self bias voltage of cathode from 100 to 900 V. Both the residual compressive stress and the hardness decrease from 1.7 to 1.0 GPa and from 2750Kgf/$\textrm{mm}^2$ to 1700Kgf/$\textrm{mm}^2$, respectively. In addition to hydrogen, triply bonded nitrogens also play a role of teminal sites of the three dimensional atomic bond network. By considering the hydrogen concentration and the nitrogen bond characteristics, it can be shown that the mechanical properties of the films are determined by the content of three dimensional inter-links of $sp^2$ clusters. Although the mechanical properties are affected by the nitrogen addition, its depedence on the negative bias voltage is qualitatively identical to that of pure diamond-like carbon films.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.170-170
• /
• 2011

태양전지와 박막 트랜지스터를 위한 유망한 재료로서 수소화된 비정질 실리콘과 나노결정 실리콘 박막이 관심을 받아 왔다. 특히, 수소화된 나노결정 실리콘 박막은 비정질 대비 높은 방향성과 조밀한 구조 덕에 박막 태양전지나 TFT(Thin film transistor) 소자의 성능 향상에 기여할 수 있는 물질로 연구되고 있다. 이러한 박막들은 보통 $SiH_4$같은 Si을 포함한 가스에 다량의 $H_2$를 희석시켜 플라즈마 화학 증착법(PECVD, Plasma Enhanced Chemical Vapor Deposition)에 의해 성장된다. 이러한 CVD증착 방식을 이용하여 결정화된 박막을 얻기 위해서는 대개 높은 수소 희석비를 이용하는 것이 일반적이나, 이러한 공정 방식은 실리콘이 결합되어야 할 결합위치에 bonding energy가 더 높은 수소의 결합을 촉진하게 된다. 이러한 특성은 박막 태양전지에서 효율을 떨어뜨리는 주요 요소로 작용하고 있다.(1) 본 연구에서는 수소의 결합 확률을 낮춘 결정화된 박막을 성장시키기 위해 수소를 대신하여 헬륨을 희석가스로 사용하여 박막을 증착하고 그 특성을 분석해 보았다. 박막의 구조적 특성, 결정화도(Xc), 플라즈마 내 활성 라디칼(Active radical in plasma), Si-H결합 특성, 전도도(Conductivity)와 같은 박막 특성을 알아보기 위해 주사전자현미경(SEM, Scanning Electron Microscopy), 라만 분광기(Raman spectroscopy), 광 방출 분광기(OES, Optical Emission Spectrocopy), 적외선 분광기(FT-IR, Fourier Transform-Infrared Spectroscopy), Keithley measurement kit이 사용되었다. 수소를 대신하여 헬륨을 사용함으로써 동일 결정화도 대비 10%이상 낮은 microstructure factor 값을 얻을 수 있었으며 인가되는 RF 전력을 140W까지 증가시켰을 때 약 80%의 결정화도를 관찰할 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.409-409
• /
• 2010

솔라셀은 차세대 대체 에너지 소스로 최근 큰 각광을 받고 있다. 솔라셀의 제조에 있어 가장 중요한 공정은 마이크로 결정질 및 비결정질 실리콘(uC-Si:H and a-Si:H) 박막을 증착하는 PECVD (Plasma Enhanced CVD)공정이다. 현재까지 이 증착공정을 위한 플라즈마 소스로 CCP(Capacitively Coupled Plasma)가 주로 사용되어 왔다. 그러나, CCP를 플라즈마 소스를 사용한 경우 솔라셀 대량 생산 적용시 다른 방법들에 비해 긴 공정 시간이 해결해야 할 문제점으로 대두되었다. 본 발표에서는 솔라셀의 대량 생산을 위한 마이크로 결정질 실리콘 박막 증착에 있어 현 시점에서 해결되어야 할 문제점에 대해 고찰해 보고자 한다. 현재까지 이러한 문제점들을 해결하기 위해 적용되어 왔던 플라즈마 소스들을 나열하고 이러한 플라즈마 소스에 대한 특성 및 문제점들을 고찰한다. 또한, PECVD 공정상의 문제점을 해결하기 위한 플라즈마 조건을 플라즈마 벌크에서의 전자에너지 분포를 기준으로 제시하고자 한다. 솔라셀용 결정질 실리콘 박막 증착용 플라즈마 소스로 hollow cathode 방전이 가장 유력시되고 있다. 본 연구에서는 CCP 플라즈마에서 hollow cathode 방전시 발생되는 플라즈마 특성에 대한 기초 연구를 제시한다. 기초 연구를 위해 다양한 불활성 가스인 아르콘, 헬륨, 크립톤 가스에 13.56 MHz의 RF 파워를 인가하고 방전되는 플라즈마 밀도 변화를 관찰하였다. 특히, 다양한 hole diameter에서 발생되는 플라즈마 밀도의 변화를 기존 평면 CCP 플라즈마의 밀도에 비교하여 분석함으로써 hole diameter에 따른 효과를 관찰하였다. 이러한 결과는 PIC 시뮬레이션을 통해 얻은 전자에너지 분포함수를 바탕으로 메커니즘을 논의하고자 한다. 마지막으로 솔라셀용 PECVD공정을 위해 고밀도 플라즈마 소스의 필요성뿐 만 아니라 대면적 소스의 구현에 대한 문제점을 고찰하였다. 대면적 공정에서 가장 중요한 핵심 연구 이슈는 공정 균일도를 높이는 것이다. CCP 플라즈마 소스에서 전극의 크기가 대면적화 됨에 따라 발생되는 전자기파 효과에 의한 불균일도에 대해 RF 전자기장 시뮬레이션을 통해 확인하고, 균일도 확보를 위한 방안에 대한 논의하고자 한다.

• Journal of Ceramic Processing Research
• /
• v.20 no.6
• /
• pp.589-596
• /
• 2019

Pigments with minute particle sizes, such as carbon black (CB) and pigment red 48:2 (P.R.48:2), are the most important types of pigment and have been widely used in many industrial applications. However, minute particles have large surface areas, high oil absorption and low surface energy. They therefore tend to be repellent to the vehicle and lose stability, resulting in significant increases in viscosity or reaggregation in the vehicle. Therefore, finding the best way to improve the dispersion properties of minute particle size pigments presents a major technical challenge. In this study, minute particle types of CB and P.R.48:2 were treated with nitrogen gas plasma generated via radio frequency-plasma enhanced chemical vapor deposition (RF-PECVD) to increase the dispersion properties of minute particles in deionized (DI) water. The morphologies and particle sizes of untreated and plasma treated particles were evaluated using scanning electron microscopy (SEM) and atomic force microscopy (AFM). The average distributions of particle size were measured using a laser particle sizer. Fourier transform infrared spectroscopy was carried out on the samples to identify changes in molecular interactions during plasma processing. The results of our analysis indicate that N2 plasma treatment is an effective method for improving the dispersibility of minute particles of pigment in DI water.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.44-44
• /
• 2009

Recently, transparent ZnO-based TFTs have attracted much attention for flexible displays because they can be fabricated on plastic substrates at low temperature. We report the fabrication and characteristics of ZnO channel layers(ZnO TFTs) having different channel thicknesses. The ZnO film were deposited as active channel layers on $Si_3N_4/Ti/SiO_2p$-Si substrates by rf magnetron sputtering at $100\;^{\circ}C$ without additional annealing. Also the Zno thin films deposited at oxygen partial pressures of 40%. ZnO TFTs using a bottom-gate configuration were investigated. The $Si_3N_4$ film were deposited as gate insulator by PE-CVD at $15\;^{\circ}C$. All Processes were processed below $150^{\circ}C$ which is optimal temperature for flexible display and were used dry etching method.

• Journal of the Korean Ceramic Society
• /
• v.31 no.2
• /
• pp.206-212
• /
• 1994

Effects of the film deposition process parameters on the properties such as deposition rate, etch rate, refractive index, stress and step coverage of plasma enhanced chemical vapor deposited (PECVD) tetraethylorthosilicate glass (TEOS) SiO2 film were investigated and analysed using SEM, FTIR and SIMS techniques. Increasing TEOS flow or decreasing O2 flow increased the deposition rate and the compressive stress of the oxide film but produced a less denser film. The deposition rate decreased owing to the decrease in the sticking coefficient of the TEOS and the O2 molecules onto the substrate Si with increasing the substrate temperature. Increasing the substrate temperature produced a denser film with a lower etch rate and the higher refractive index by lowering SiOH and moisture contents. Increasing the rf power increases the ion bombardment energy. This increase in energy, in turn, increases the deposition rate and tends to make the film denser. No appreciable changes were found in the deposition rate but the refractive index and the stress of the film decreased with increasing the deposition pressure. The carbon content in the plasma TEOS CVD oxide film prepared under our standard deposition conditions were very low according to the SIMS analysis results.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1340-1342
• /
• 1998

The diamond-like carbon(DLC) film, as an antireflection layer, is coated on a commerically used Ge window. DLC films are deposited by using an rf(13.56 MHz) plasma CVD. The optimal value of thickness and refractive index of DLC layer has been determined from the computer simulation. IR-transmittances of DLC-coated Ge windows are estimated by measuring FTIR spectra in the wavelength range of$ 2.5{\sim}25{\mu}m$. By coating the DLC film on one side of the Ge window, the transmittance measured at a wavelength of $10{\mu}m$ is about 60 %, while that of the bare Ge is lower than 50 %. Also, a higher transmittance up to about 90 % is obtained by coating the DLC film on both sides of the window. It may be suggested that the further improvement of the IR-transmittance can be achieved by more precisely controlling the thickness and the refractive index of DLC layer and also by adopting various muliti-layer antireflection structures.