• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.3
• /
• pp.282-288
• /
• 2014

In this paper, we have analyzed and designed a digital RF receiver based on the optimization of the dynamic range parameter to secure the wideband characteristics and linearity of digital radar receivers. To improve the wideband characteristics and dynamic range, a low noise amplifier is matching design with a noise source to minimize the noise figure in 1 GHz bandwidth and we improved the linearity of RF-receiver by securing the conversion gain characteristics of receiver through the design of active mixer. RF receiver is designed to give gain 63 dB, noise figure 1.2 dB and dynamic range of RF receiver has 75.8 dB in a wide band of 8.8~9.8 GHz. It is shown to be applicable to X-band digital radar receiver.

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.817-820
• /
• 1999

In this paper, we describes RF receiver module for IMT-2000 handset with 5MHz channel bandwidth. The fabricated RF receiver module consists of Low Noise Amplifier-, RF SAW filter, Down-converter, IF SAW filter, AGC and PLL Synthesizer. The NF and IIP3 of LNA is 0.8㏈, 3㏈m at 2.14㎓, conversion gain of downconverter is l0㏈, dynamic range of AGC is 80㏈, and phase noise of PLL is -100 ㏈m, at 100KHz. The receiver sensitivity is -110㏈m, adjacent channel selectivity is -48㏈m.

• ETRI Journal
• /
• v.37 no.4
• /
• pp.647-656
• /
• 2015

This paper proposes a single-RF MIMO receiver that adopts a beam-switching antenna (BSA) instead of a conventional array antenna. The beauty of the proposed single-RF MIMO receiver with BSA is that it can be deployed in a very small physical space while achieving a full spatial multiplexing gain. Our analysis has revealed that the use of a BSA inevitably results in the spectrum spreading effect at the RF output, which in turn causes an SNR decrease and adjacent channel interference (ACI). Two novel receiver techniques are proposed to mitigate the issues of redundant sub-band suppression and ACI avoidance. Numerical analysis results verify the performance improvement from the proposed receiver techniques.

• Proceedings of the IEEK Conference
• /
• 2000.06a
• /
• pp.65-68
• /
• 2000

In this paper, design parameters are investigated and design procedure is established for PCS mobile station, especially for receiver RF block. And simulation environment to analyze parameters of the receiver RF block to determine whether it satisfies the receiver standard, IS-98C, is calculated. Design parameters are simulated and optimized. With simulated results, PCS mobile station is implemented and tested. Measured results show good agreement with simulation Design procedure can be used to get optimum characteristics for each of receiver block. By using optimum characteristics, mobile station can be designed more efficiently.

• Journal of the Korea Society of Computer and Information
• /
• v.24 no.7
• /
• pp.71-78
• /
• 2019

This paper describes a design for a RF receiver to receive satellite digital audio service. The RF receiver designed in this study is a planar structure that is easy to install on the rooftop of a car and is compact in size. In addition, it can be applied to certain commercial models because it has low noise and high gain characteristics. The impedance bandwidth of antenna is 17.8%(415MHz), and the axial ratio is below 3dB as good properties for the bandwidth of 40MHz which is a satellite digital audio service band. Also, it had a broad radiation beamwidth of $95.41^{\circ}$ in H-plane and $117.45^{\circ}$ in E-plane. From the results of the field test of satellite digital audio service reception for the RF receiver, it demonstrated good C/N rate(10.2dB).

• Journal of Broadcast Engineering
• /
• v.21 no.5
• /
• pp.803-815
• /
• 2016

In this paper, we design a direct radio frequency (RF) sampling receiver for multiband GNSS signals and demonstrate its performance. The direct RF sampling is a technique that does not use an analog mixer, but samples the passband signal directly, and all receiver processes are done in digital domain, whereas the conventional intermediate frequency (IF) receiver samples the IF band signals. In contrast to the IF sampling receiver, the RF sampling receiver is less complex in hardware, reconfigurable, and simultaneously converts multiband signals to digital signals with an analog-to-digital (AD) converter. The reconfigurability and simultaneous reception are very important in military applications where rapid change to other system is needed when a system is jammed by an enemy. For simultaneous reception of multiband signals, the sampling frequency should be selected with caution by considering the carrier frequencies, bandwidths, desired intermediate frequencies, and guard bands. In this paper, we select a sampling frequency and design a direct RF sampling receiver to receive multiband global navigation satellite system (GNSS) signals such as GPS L1, GLONASS G1 and G2 signals. The receiver is implemented with a commercial AD converter and software. The receiver performance is demonstrated by receiving the real signals.

• Journal of Positioning, Navigation, and Timing
• /
• v.3 no.3
• /
• pp.91-97
• /
• 2014

A direct RF sampling method refers to a technique that directly converts a passband signal to an intermediate band or a baseband without using a mixer. This method is less complicated than an existing RF receiver because a mixer is not used. It uses digital processing after sampling, and thus can flexibly process signals in a number of bands using software. In this process, it is important to select an appropriate sampling frequency so that a number of signals can be converted to an intermediate band that is easy to process. In this study, going beyond previously studied direct RF sampling frequency selection methods, conditions that need to be additionally considered during receiver design were examined, and the structure of a direct RF sampling receiver that satisfies these conditions was suggested.

• Journal of the Korean Institute of Navigation
• /
• v.22 no.1
• /
• pp.51-54
• /
• 1998

In this paper, RF receiver for CDMA system which has 10 MHz in the channel bandwidth has been designed and fabricated. The designed and fabricated RF receiver is shown useful in operation and the performance has been confirmed by experiments. The results are to be used for establishment of a broadband CDMA wireless access specification standard for WLL system in 2.3 GHz band.

• Journal of electromagnetic engineering and science
• /
• v.14 no.2
• /
• pp.61-67
• /
• 2014

This paper presents a zero-IF CMOS RF receiver, which supports three channel bandwidths of 5/10/40MHz for LTE-Advanced systems. The receiver operates at IMT-band of 2,500 to 2,690MHz. The simulated noise figure of the overall receiver is 1.6 dB at 7MHz (7.5 dB at 7.5 kHz). The receiver is composed of two parts: an RF front-end and a baseband circuit. In the RF front-end, a RF input signal is amplified by a low noise amplifier and $G_m$ with configurable gain steps (41/35/29/23 dB) with optimized noise and linearity performances for a wide dynamic range. The proposed baseband circuit provides a -1 dB cutoff frequency of up to 40MHz using a proposed wideband OP-amp, which has a phase margin of $77^{\circ}$ and an unit-gain bandwidth of 2.04 GHz. The proposed zero-IF CMOS RF receiver has been implemented in $0.13-{\mu}m$ CMOS technology and consumes 116 (for high gain mode)/106 (for low gain mode) mA from a 1.2 V supply voltage. The measurement of a fabricated chip for a 10-MHz 3G LTE input signal with 16-QAM shows more than 8.3 dB of minimum signal-to-noise ratio, while receiving the input channel power from -88 to -12 dBm.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.7
• /
• pp.500-507
• /
• 2018

A three-channel radio frequency (RF) monopulse receiver using a data signal with a maximum transmission rate of 274 Mbps was designed. A monopulse receiver using a broadband communication signal was designed to operate in the Ku band, and it consists of a down-conversion module and a signal-processing module. To satisfy the performance of the proposed RF monopulse receiver, a signal-processing function less than the reception sensitivity for each transmission rate according to the adaptive transmission rate is required. To minimize signal reception and mutual frequency interference of various bandwidths, two RF filters were applied. To verify the satisfaction of system requirements, an AWR Corp. simulation tool was used.