• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.3
• /
• pp.277-283
• /
• 2009

In this paper, aluminum doped zinc oxide (ZnO:Al) thin films on plastic substrate such as poly carbonate (PC), polyethylene terephthalate (PET) were prepared by RF magnetron sputtering method for flexible solar cell applications. Effects of the sputter pressure on the structural, electrical and optical properties were investigated. The crystallinity and the degree of the (002) orientation were deteriorated with increasing the sputter pressure. When the sputter pressure was higher, the conductivity of ZnO:Al films was improved because of the high carrier concentration and the Hall mobility. High quality ZnO:Al films with resistivity as low as $1.9{\times}10^{-3}{\Omega}-cm$ and the optical transmittance over 80 % in the visible region have been obtained on PC substrate at 2 mTorr.

• Applied Science and Convergence Technology
• /
• v.23 no.6
• /
• pp.366-370
• /
• 2014

ZnO:Al transparent conductive films were deposited on glass substrates by RF magnetron sputtering technique and annealed by rapid thermal annealing system. The influence of annealing time on the structural, electrical, and optical properties of ZnO:Al thin films was investigated by atomic force microscopy, X-ray diffraction, Hall method and optical transmission spectroscopy. As the annealing time increases from 0 to 5 min, the crystallinity is improved, the root main square surface roughness is decreased and the sheet resistance is decreased. The lowest sheet resistance of ZnO:Al thin film is 90 ohm/sq. The reduction of sheet resistance is caused by increasing carrier concentration due to substituent Al ion. All films are transparent up to 80% in the visible wavelength range and the adsorption edge is a blue-shift due to Burstein-Moss effect with increasing annealing time.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.164-164
• /
• 2010

Cds films were deposited on glass substrates using rf magnetron sputtering method followed by rapid thermal annealing(RTA). Effects of annealing temperature on surface characteristic, structural, electrical and optical property of CdS films were investigated at different temperatures ranging from 250 to $550^{\circ}C$ with various holding time. The film annealed at $450^{\circ}C$ with less than 1 min holding time is attributed to the improved crystalline quality of CdS film due to the effective relaxation of residual compressive stress and achieving maximum grain size. The results show that RTA treatments under optimal annealing condition can provide significant improvements in the properties of CdS films.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.688-692
• /
• 2004

In this paper, zinc oxide (ZnO) films with c-axis (002) orientation have been successfully deposited on the Al/Si substrate by rf magnetron sputtering method. The deposited films were characterized by substate temperature. Physical and structural properties of the deposited films were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and atomic force microscopy (AFM) measurement. Electrical Properties of the deposited films were investigated by 4-poing probe and LCR meter measurement. The optimal condition in this experimental result was found at foot of the substrate temperature and shown good film quality for FBAR application.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.189-193
• /
• 1997

(S $r_{0.85}$/C $a_{0.15}$)Ti $O_3$(SCT) thin films at various deposition temperature and rf power were grown by rf magnetron sputtering method on optimized Pt-based electrodes (Pt/TiN/ $SiO_2$/Si). The crystallinity of the films increases with increasing deposition temperature. SCT thin film is depend on the surface morphology and crystallinity of Pt films for bottom electrode. Dielectric constant of (S $r_{0.85}$C $a_{0.15}$)Ti $O_3$ thin films deposited on Si wafer substrate are larger with the increase of deposition temperature and gain size.in size.

• Current Photovoltaic Research
• /
• v.9 no.1
• /
• pp.1-5
• /
• 2021

The properties of the electron transport layer (ETL) have a great effect on perovskite solar cell performance. Depositing conformal SnO2 ETL on bottom textured silicon cells is essential to increase current density in terms of the silicon-perovskite tandem solar cells. In the recent study, the SnO2 electron transport layer deposited by the sputtering method showed an efficiency of 19.8%. Also, an electron transport layer with a sputtered TiO2 electron transport layer in a 4-terminal tandem solar cell has been reported. In this study, we synthesized SnOx ETL with a various sputtering power range of 30-60W by Radio-frequency (RF)-magnetron sputtering. The properties of SnOx thin film were characterized using ellipsometer, UV-vis spectrometer, and IV measurement. With a sputtering power of 50W, the solar cell showed the highest efficiency of 13.3%, because of the highest fill factor by the conductivity of SnOx film.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.8
• /
• pp.764-768
• /
• 2006

For the possible application of pearl pigment, multi-layered $TiO_2/Al,\;Cr/TiO_2$ thin film were deposited on $SiO_2$ substrate by using sputtering method, $TiO_2$ and Al or Cr was selected as a possible high and low refraction material at the film interface respectively. Optical properties including color effect were systematically studied in terms of different film thickness and film layers by using spectrometer. In order to expect the experimental results, the simulation program, the Essential Macleod Program(EMP) was adopted and compared with the experimental data. The film consisting of $TiO_2/Al,\;Cr/TiO_2$ layers shows a wavelength range of $430{\sim}760nm$, typically color ranges between bluish purple and red. It was confirmed that this experimental result was quite well consistent with the experimental one.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.10
• /
• pp.1023-1028
• /
• 2004

We fabricated AIN thin film by using RF magnetron sputtering and studied the structural characteristic of AIN thin film with the change of the deposition conditions such as Ar/$N_2$ flow ratio, working pressure, and the distance between substrate and target. The orientation and surface roughness of AIN thin film were studied by using XRD and AFM. We can not identify the orientation of the thin film deposited in Ar, while we obtained the (l00) orientation of the thin film with the addition of $N_2$. Especially, the thin film deposited at 18/2 (seem) of Ar/$N_2$ flow ratio exhibited to be the most (100) oriented. The (100) orientation of thin film becomes weaker as the working pressure becomes higher. The further distance between substrate and target is stronger the (100) orientation of the thin film, but the (100) orientation becomes weaker and (002) orientation started to appear as the distance is shorter. The surface roughness of the thin film deposited at 50$0^{\circ}C$ in Ar only is 1.1 nm, while very smooth thin film of 0.4～0.6 nm is obtained with the addition of $N_2$.

• Journal of the Korean Ceramic Society
• /
• v.41 no.1
• /
• pp.36-40
• /
• 2004

$SnO_2$ thin films were deposited on a $SiO_2$/Si substrate with the flow of Ar and $O_2$ of 25 sccm by RF-magnetron sputtering method. the post-annealing was conducted at $500^{\circ}C$ in atmosphere of dry air and $N_2$ were changed fairly, while those annealed in dry air resembled as-deposited films. This may be attributed to the desorption of adsorbed oxygen and the extraction of lattice oxygen during annealing. Resistivity of films annealed in $N_2$ was increased over 5 times than that of as-deposited films. It can be explained that the increment of resistivity may result from the discontinuous conduction path with change of microstructures after annealing in $N_2$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.9
• /
• pp.731-735
• /
• 2001

S $r_{0.89}$B $i_{2.4}$T $a_2$ $O_{9}$ (SBT) thin films are deposited on Pt-coated electrode(Pt/Ti $O_2$/ $SiO_2$/Si) using RF magnetron sputtering method. In the XRD pattern, the SBT thin films had (105) orientation. As annealing temperature was increased from $600^{\circ}C$ to 85$0^{\circ}C$, the intensities of peak were increased. In the SEM images, Bi-layered perovskite phase was crystallized above $650^{\circ}C$ and rod-like grains grew above 75$0^{\circ}C$. The maximum remanent polarization and the coercive electric field at annealing temperature of 75$0^{\circ}C$ are 11.60$\mu$C/$\textrm{cm}^2$ and 48kV/cm respectively. The dielectric constant and leakage current density at annealing temperature of 75$0^{\circ}C$ are 213 and 1.01x10$^{-8}$ A/$\textrm{cm}^2$, respectively. The fatigue characteristics of SBT thin filmsdid not change up to 10$^{10}$ switching cycles.s.s.