• 한국전기전자재료학회논문지
• /
• 제22권10호
• /
• pp.821-825
• /
• 2009

Recently, transparent ZnO-based TFTs have attracted much attention for flexible displays because they can be fabricated on plastic substrates at low temperature. We report the fabrication and characteristics of ZnO TFTs having different channel thicknesses deposited at low temperature. The ZnO films were deposited as active channel layer on $Si_3N_4/Ti/SiO_2/p-Si$ substrates by RF magnetron sputtering at $100^{\circ}C$ without additional annealing. Also, the ZnO thin films deposited at oxygen partial pressures of 40%. ZnO TFTs using a bottom-gate configuration were investigated. The $Si_3N_4$ film was deposited as gate insulator by PE-CVD at $150^{\circ}C$. All Processes were processed below $150^{\circ}C$ which is optimal temperature for flexible display and were used dry etching method. The fabricated devices have different threshold slop, field effect mobility and subthreshold slop according to channel thickness. This characteristics are related with ZnO crystal properties analyzed with XRD and SPM. Electrical characteristics of 60 nm ZnO TFT (W/L = $20\;{\mu}m/20\;{\mu}m$) exhibited a field-effect mobility of $0.26\;cm^2/Vs$, a threshold voltage of 8.3 V, a subthreshold slop of 2.2 V/decade, and a $I_{ON/OFF}$ ratio of $7.5\times10^2$.

• Journal of Magnetics
• /
• 제5권4호
• /
• pp.120-123
• /
• 2000

Co-Ni-Fe-N thin films were fabricated by a $N_2$ reactive rf magnetron sputtering method. The nitrogen partial pressure ($P_{N2}$) was varied in the range 0~10% . As$P_{N2}$ increases in this range, the saturation magnetization $B_s$ linearly decreases from 19.8 kG to 14 kG and the electrical resistivity ($\rho$) increases from 27 to 155 $\mu\Omegacm$. The coercivity $H_c$ exhibits the minimum value at 4% $P_{N2}$. The magnetic anisotropy fields ($H_k$) are in the range of 20$\sim$50 Oe. High frequency characteristics of $(Co_{22.2}Ni_{27.6}Fe_{50.2})_{100-x}N_x$ films are excellent in the range of 3$\sim$5% of $P_{N2}$. In particular, the effective permeability of the film fabricated at 4% $P_{N2}$ is 800, which is maintained up to 600 MHz. This film also shows Bs of 17.5 kG, $H_c$/ of 1.4 Oe, resistivity of 98$\mu\Omegacm$ and $H_k$ of about 25 Oe. Also, the corrosion resistance of $(Co_{22.2}Ni_{27.6}Fe_{50.2})_{100-x}N_x$ films was imp roved with increasing N concentration.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2000년도 International Symposium on Magnetics The 2000 Fall Conference
• /
• pp.492-499
• /
• 2000

Co-Ni-Fe-N thin films were fabricated by a N$\sub$2/ reactive rf magnetron sputtering method. The nitrogen partial pressure (P$\sub$N2/) was varied in the range of 0∼10%. As P$\sub$N2/ increases in this range, the saturation magnetization (B$\sub$s/) linearly decreases from 19.8 kG to 14 kG and the electrical resistivity ($\rho$) increased from 27 to 155 ${\mu}$$\Omega$cm. The coercivity (H$\sub$c/) exhibits the minimum value at 4% of P$\sub$N2/. The magnetic anisotropy (H$\sub$k/) are in the range of 20∼50 Oe. High frequency characteristics of (Co$\sub$22.2/Ni$\sub$27.6/Fe$\sub$50.2/)$\sub$100-x/N$\sub$x/ films are excellent in the range of 3∼5% of P$\sub$N2/. Especially the effective permeability of the film fabricated at 4% of P$\sub$N2/ is 800, which is maintained up to 600 MHz. This film also shows Bs of 17.5 kG, H$\sub$c/ of 1.4 Oe, resistivity of 98 $\Omega$cm and H$\sub$k/ of about 25 Oe. Also, the corrosion resistance of (Co$\sub$22.2/Ni$\sub$27.6/Fe$\sub$50.2/)$\sub$100-x/N$\sub$x/ were improved with the increase in N concentration.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2016년도 추계학술대회 논문집
• /
• pp.195-195
• /
• 2016

Titanium and its alloys are widely used as implants in orthopedics, dentistry and cardiology due to their outstanding properties, such as high strength, high level of hemocompatibility and enhanced biocompatibility. Hence, recent works showed that the synthesis of new Ti-based alloys for implant application involves more biocompatible metallic alloying element, such as, Nb, Hf, Zr and Mo. In particular, Nb and Hf are one of the most effective Ti ${\beta}-stabilizer$ and reducing the elastic modulus. Plasma electrolyte oxidation (PEO) is known as excellent method in the biocompatibility of biomaterial due to quickly coating time and controlled coating condition. The anodized oxide layer and diameter modulation of Ti alloys can be obtained function of improvement of cell adhesion. Silicon (Si) and magnesium (Mg) has a beneficial effect on bone. Si in particular has been found to be essential for normal bone and cartilage growth and development. In vitro studies have shown that Mg plays very important roles in essential for normal growth and metabolism of skeletal tissue in vertebrates and can be detected as minor constituents in teeth and bone. The aim of this study is to research Si and Mg doped hydroxyapatite film formation by plasma electrolytic oxidation. Ti-29Nb-xHf (x= 0, 3, 7 and 15wt%, mass fraction) alloys were prepared Ti-29Nb-xHf alloys of containing Hf up from 0 wt% to 15 wt% were melted by using a vacuum furnace. Ti-29Nb-xHf alloys were homogenized for 2 hr at $1050^{\circ}C$. Each alloy was anodized in solution containing typically 0.15 M calcium acetate monohydrate + 0.02 M calcium glycerophosphate at room temperature. A direct current power source was used for the process of anodization. Anodized alloys was prepared using 270V~300V anodization voltage at room. A Si and Mg coating was produced by RF-magnetron sputtering system. RF power of 100W was applied to the target for 1h at room temperature. The microstructure, phase and composition of Si and Mg coated oxide surface of Ti-29Nb-xHf alloys were examined by FE-SEM, EDS, and XRD.

• 한국진공학회지
• /
• 제21권1호
• /
• pp.12-16
• /
• 2012

Top-Emitting OLED (Organic Light-Emitting Diode) 디스플레이에서는 반사율이 가장 높은 Ag (silver) 박막이 쓰이고 있지만, 소자에서 요구되는 일함수(work function)가 상대적으로 낮기 때문에 전극과 유기물간에 에너지 장벽이 발생하여 발광효율을 낮추는 요인이 되고 있다. 본 논문에서는 Ag 전극의 일함수를 높이기 위한 연구를 진행하였으며, 박막 형태의 Ag 전극에 대하여 nanotribology 접근법으로 연구를 실행하였다. Ag는 rf magnetron sputter를 이용해 glass 위에 증착한 후 furnace에서 $300^{\circ}C$, 30분간 대기 중에서 열처리하였고, 또 다른 시료는 표면에 산소 상압플라즈마로 처리 시간(30, 60, 90, 120s)을 각기 다르게 하여 시료를 제조하였다. Ag 전극을 nanoindentation을 통해 국부 영역에 대한 물리적 특성의 변화를 측정하였고, Kelvin probe force microscopy을 이용해 시료 표면의 포텐셜을 측정했다. 그 결과 열처리한 시료의 포텐셜값은 가장 크게 증가하였지만 균일도가 낮아졌다. 120s 플라즈마 처리한 시료는 불완전한 산화막의 생성으로 인해 탄성계수 및 경도값과 박막의 Weibull modulus를 극히 낮게 만들었지만, 60s, 90s 플라즈마 처리는 시료의 균일도를 높이고 또한 포텐셜을 증가시켜 T-OLED 성능 개선에 좋은 영향을 미치게 될 것이다.

• 센서학회지
• /
• 제9권1호
• /
• pp.36-43
• /
• 2000

휘발성염기질소가스 중에서 TMA 가스의 선택성을 향상시키고 동작온도가 낮고 저농도에서 감도가 높은 반도체가스센서를 제작하기 위해 ZnO에 촉매불순물 $Al_2O_3$, $TiO_2$, $In_2O_3$ 및 $V_2O_5$등의 다양한 무게비가 함유된 ZnO계 타겟을 제작한 후 RF 마그네트론 스펏터링법으로 산소분위기에서 박막을 증착시켰다. 센서의 전기적 안정성을 위해 $700^{\circ}C$에서 1시간동안 산소분위기에서 열처리한 ZnO계 박막으로 센서를 제작한 후 DMA(dimethylamine), 암모니아($NH_3$) 및 TMA(trimethylamine) 가스의 감도를 조사하였다. TMA 가스선택성은 DMA 및 암모니아가스에 대한 TMA 가스의 감도비($S_{TMA}/S_{DMA}$, $S_{TMA}/S_{NH3}$)로 정의하였다. $ZnO+Al_2O_3(4\;wt.%)+TiO_2(1\;wt.%)+In_2O_3(1\;wt.%)$ 센서는 160 ppm의 가스농도와 동작온도 $300^{\circ}C$에서 DMA와 암모니아가스에 대한 TMA 가스의 최대 감도비가 각각 5.9와 26을 나타내어 선택성이 향상되었음을 알 수 있었다.

• 한국재료학회지
• /
• 제18권4호
• /
• pp.169-174
• /
• 2008

The structural and electrical properties of amorphous $BaSm_2Ti_4O_{12}$ (BSmT) films on a $TiN/SiO_2/Si$ substrate deposited using a RF magnetron sputtering method were investigated. The deposition of BSmT films was carried out at $300^{\circ}C$ in a mixed oxygen and argon ($O_2$ : Ar = 1 : 4) atmosphere with a total pressure of 8.0 mTorr. In particular, a 45 nm-thick amorphous BSmT film exhibited a high capacitance density and low dissipation factor of $7.60\;fF/{\mu}m2$ and 1.3%, respectively, with a dielectric constant of 38 at 100 kHz. Its capacitance showed very little change, even in GHz ranges from 1.0 GHz to 6.0 GHz. The quality factor of the BSmT film was as high as 67 at 6 GHz. The leakage current density of the BSmT film was also very low, at approximately $5.11\;nA/cm^2$ at 2 V; its conduction mechanism was explained by the the Poole-Frenkel emission. The quadratic voltage coefficient of capacitance of the BSmT film was approximately $698\;ppm/V^2$, which is higher than the required value (<$100\;ppm/V^2$) for RF application. This could be reduced by improving the process condition. The temperature coefficient of capacitance of the film was low at nearly $296\;ppm/^{\circ}C$ at 100 kHz. Therefore, amorphous BSmT grown on a TiN substrate is a viable candidate material for a metal-insulator-metal capacitor.

• 한국자기학회지
• /
• 제10권4호
• /
• pp.171-177
• /
• 2000

RF 마그네트론 스퍼터링 증착법으로 제작한 Co/NiMn 이층막에서의 교환자기결합현상을 연구하였다. 어닐링의 온도와 시간에 따른 교환자기결합력(H$_{ex}$)의 변화를 조사하여 300 $^{\circ}C$에서 13시간의 열처리후에 최대의 교환결합자장을 얻을 수 있음을 보였고, NiMn과 Co층의 적층순서를 변화시켰을 때, NiMn 상층구조의 시편이 더 높은 교환자기결합력을 나타냄을 알 수 있었다. 상층의 Ta 보호막의 사용이 교환자기결합을 나타내는데 필수적임을 알 수 있었는데 , AES 분석은 Ta 보호층을 적용하지 않은 경우에, 산소원자가 막 내부의 깊은 곳까지 침투함으로 인하여 교환자기결합력이 일어나지 않음을 보여주었다. 또한 교환자기결합에 대한 Ta 바닥층의 효과를 연구하였다. Ta 바닥층은 높은 교환자기결합력을 얻기 위해서는 사용하지 않는 것이 낫다는 것을 알아내었다. X선 회절분석의 결과는, Ta 바닥층이 다층막에 우선방위조직을 형성시키는데 기여하지만, NiFe/NiMn 이층막에서의 경우와는 달리 교환자기결합에 반드시 필요한 조건이 아님을 보여주었다. 또한 Co층과 NiMn층의 두께에 따른 교환결합력의 영향을 조사하여, 교환결합력은 200 $\AA$ 이상의 NiMn층 적용 시 최대값을 가지며, Co층의 두께에 반비례함을 알 수 있었다.다.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2012년도 춘계학술발표대회
• /
• pp.65-65
• /
• 2012

Copper zinc tin sulfide ($Cu_2ZnSnS_4$, CZTS) is a very promising material as a low cost absorber alternative to other chalcopyrite-type semiconductors based on Ga or In because of the abundant and economical elements. In addition, CZTS has a band-gap energy of 1.4~1.5eV and large absorption coefficient over ${\sim}10^4cm^{-1}$, which is similar to those of $Cu(In,Ga)Se_2$(CIGS) regarded as one of the most successful absorber materials for high efficient solar cell. Most previous works on the fabrication of CZTS thin films were based on the vacuum deposition such as thermal evaporation and RF magnetron sputtering. Although the vacuum deposition has been widely adopted, it is quite expensive and complicated. In this regard, the solution processes such as sol-gel method, nanocrystal dispersion and hybrid slurry method have been developed for easy and cost-effective fabrication of CZTS film. Among these methods, the hybrid slurry method is favorable to make high crystalline and dense absorber layer. However, this method has the demerit using the toxic and explosive hydrazine solvent, which has severe limitation for common use. With these considerations, it is highly desirable to develop a robust, easily scalable and relatively safe solution-based process for the fabrication of a high quality CZTS absorber layer. Here, we demonstrate the fabrication of a high quality CZTS absorber layer with a thickness of 1.5~2.0 ${\mu}m$ and micrometer-scaled grains using two different non-vacuum approaches. The first solution-processing approach includes air-stable non-toxic solvent-based inks in which the commercially available precursor nanoparticles are dispersed in ethanol. Our readily achievable air-stable precursor ink, without the involvement of complex particle synthesis, high toxic solvents, or organic additives, facilitates a convenient method to fabricate a high quality CZTS absorber layer with uniform surface composition and across the film depth when annealed at $530^{\circ}C$. The conversion efficiency and fill factor for the non-toxic ink based solar cells are 5.14% and 52.8%, respectively. The other method is based on the nanocrystal dispersions that are a key ingredient in the deposition of thermally annealed absorber layers. We report a facile synthetic method to produce phase-pure CZTS nanocrystals capped with less toxic and more easily removable ligands. The resulting CZTS nanoparticle dispersion enables us to fabricate uniform, crack-free absorber layer onto Mo-coated soda-lime glass at $500^{\circ}C$, which exhibits a robust and reproducible photovoltaic response. Our simple and less-toxic approach for the fabrication of CZTS layer, reported here, will be the first step in realizing the low-cost solution-processed CZTS solar cell with high efficiency.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2009년도 춘계학술대회 논문집
• /
• pp.111-112
• /
• 2009

Diamond-like carbon (DLC) is a convenient term to indicate the compositions of the various forms of amorphous carbon (a-C), tetrahedral amorphous carbon (ta-C), hydrogenated amorphous carbon and tetrahedral amorphous carbon (a-C:H and ta-C:H). The a-C film with disordered graphitic ordering, such as soot, chars, glassy carbon, and evaporated a-C, is shown in the lower left hand corner. If the fraction of sp3 bonding reaches a high degree, such an a-C is denoted as tetrahedral amorphous carbon (ta-C), in order to distinguish it from sp2 a-C [2]. Two hydrocarbon polymers, that is, polyethylene (CH2)n and polyacetylene (CH)n, define the limits of the triangle in the right hand corner beyond which interconnecting C-C networks do not form, and only strait-chain molecules are formed. The DLC films, i.e. a-C, ta-C, a-C:H and ta-C:H, have some extreme properties similar to diamond, such as hardness, elastic modulus and chemical inertness. These films are great advantages for many applications. One of the most important applications of the carbon-based films is the coating for magnetic hard disk recording. The second successful application is wear protective and antireflective films for IR windows. The third application is wear protection of bearings and sliding friction parts. The fourth is precision gages for the automotive industry. Recently, exciting ongoing study [1] tries to deposit a carbon-based protective film on engine parts (e.g. engine cylinders and pistons) taking into account not only low friction and wear, but also self lubricating properties. Reduction of the oil consumption is expected. Currently, for an additional application field, the carbon-based films are extensively studied as excellent candidates for biocompatible films on biomedical implants. The carbon-based films consist of carbon, hydrogen and nitrogen, which are biologically harmless as well as the main elements of human body. Some in vitro and limited in vivo studies on the biological effects of carbon-based films have been studied [$2{\sim}5$].The carbon-based films have great potentials in many fields. However, a few technological issues for carbon-based film are still needed to be studied to improve the applicability. Aisenberg and Chabot [3] firstly prepared an amorphous carbon film on substrates remained at room temperature using a beam of carbon ions produced using argon plasma. Spencer et al. [4] had subsequently developed this field. Many deposition techniques for DLC films have been developed to increase the fraction of sp3 bonding in the films. The a-C films have been prepared by a variety of deposition methods such as ion plating, DC or RF sputtering, RF or DC plasma enhanced chemical vapor deposition (PECVD), electron cyclotron resonance chemical vapor deposition (ECR-CVD), ion implantation, ablation, pulsed laser deposition and cathodic arc deposition, from a variety of carbon target or gaseous sources materials [5]. Sputtering is the most common deposition method for a-C film. Deposited films by these plasma methods, such as plasma enhanced chemical vapor deposition (PECVD) [6], are ranged into the interior of the triangle. Application fields of DLC films investigated from papers. Many papers purposed to apply for tribology due to the carbon-based films of low friction and wear resistance. Figure 1 shows the percentage of DLC research interest for application field. The biggest portion is tribology field. It is occupied 57%. Second, biomedical field hold 14%. Nowadays, biomedical field is took notice in many countries and significantly increased the research papers. DLC films actually applied to many industries in 2005 as shown figure 2. The most applied fields are mold and machinery industries. It took over 50%. The automobile industry is more and more increase application parts. In the near future, automobile industry is expected a big market for DLC coating. Figure 1 Research interests of carbon-based filmsFigure 2 Demand ratio of DLC coating for industry in 2005. In this presentation, I will introduce a trend of carbon-based coating research and applications.