• Journal of Communications and Networks
• /
• v.18 no.2
• /
• pp.201-209
• /
• 2016

In wireless sensor networks (WSNs) duty cycling has been an imperative choice to reduce idle listening but it introduces sleep delay. Thus, the conventional WSN medium access control protocols are bound by the energy-latency tradeoff. To break through the tradeoff, we propose a radio wave sensor called radio frequency (RF) wakeup sensor that is dedicated to sense the presence of a RF signal. The distinctive feature of our design is that the RF wakeup sensor can provide the same sensitivity but with two orders of magnitude less energy than the underlying RF module. With RF wakeup sensor a sensor node no longer requires duty cycling. Instead, it can maintain a sleep state until its RF wakeup sensor detects a communication signal. According to our analysis, the response time of the RF wakeup sensor is much shorter than the minimum transmission time of a typical communication module. Therefore, we apply duty cycling to the RF wakeup sensor to further reduce the energy consumption without performance degradation. We evaluate the circuital characteristics of our RF wakeup sensor design by using Advanced Design System 2009 simulator. The results show that RF wakeup sensor allows a sensor node to completely turn off their communication module by performing the around-the-clock carrier sensing while it consumes only 0.07% energy of an idle communication module.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.10
• /
• pp.1861-1868
• /
• 2008

In this paper, Passive Telemerty RF Sensor System using Unscented Kalman Filter algorithm(UKF) is proposed. General Passive Telemerty RF Sensor System means that it should be "wireless", "implantable" and "batterless". Conventional Passive Telemerty RF Sensor System adopts Integrated Circuit type, but there are defects like complexity of structure and limit of large power consumption in some cases. In order to overcome these kinds of faults, Passive Telemetry RF Sensor System based on inductive coupling principle is proposed in this paper. Because passive components R, L, C have stray parameters in the range of high frequency such as about 200[KHz] used in this paper, Passive Telemetry RF Sensor System considering stray parameters has to be derived for accurate model identification. Proposed Passive Telemetry RF Sensor System is simple because it consists of R, L and C and measures the change of environment like pressure and humidity in the type of capacitive value. This system adopted UKF algorithm for estimation of this capacitive parameter included in nonlinear system like Passive Telemetry RF Sensor System. For the purpose of obtaining learning data pairs for UKF Algorithm, Phase Difference Detector and Amplitude Detector are proposed respectively which make it possible to get amplitude and phase between input and output voltage. Finally, it is verified that capacitive parameter of proposed Passive Telemetry RF Sensor System using UKF algorithm can be estimated in noisy environment efficiently.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.5
• /
• pp.854-859
• /
• 2009

Many pilot projects are developed using USN(Ubiquitous Sensor network). Recently USN has more attention to be used for the applications of circumstance monitoring. In order to acquire information from sensor nodes, sensor nodes need a RF transceiver. In this paper we describe the design of a RF transceiver, based on IEEE 802.15.4, for sensor nodes operating in 2.4GHz frequency band. The architecture to be implemented and the electrical performance specifications satisfied IEEE 802.15.4 are presented. The noise figure of a receiver, selectivity, phase noise of a frequency synthesizer, transmitter's linearity and spectrum mask are derived as a design parameters from the specifications of IEEE 802.15.4.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.5
• /
• pp.858-865
• /
• 2008

In this paper, Capacitive Telemetry RF Sensor System using Recursive Least Square (RLS) algorithm was proposed. General Telemetry RF Sensor System means that it should be "wireless", "implantable" and "batterless". Conventional Telemetry RF Sensor System adopts Integrated Circuit type, but there are many defects like complexity of structure and the limitation of large power consumption in some cases. In order to overcome these disadvantages, Telemetry RF Sensor System based on inductive coupling principle was proposed in this paper. Proposed Telemetry RF Sensor System is very simple because it consists of R, L and C and measures the changes of environment like pressure and humidity in the type of capacitive value. This system adopted RLS algorithm for estimation of this capacitive parameter. For the purpose of applying RLS algorithm, proposed system was mathematically modelled with phasor method and was quasi-linearized. As two parameters such as phase and amplitude of output voltage for estimation were needed, Phase Difference Detector and Amplitude Detector were proposed respectively which were implemented using TMS320C2812 made by Texas Instrument. Finally, It is verified that the capacitance of proposed telemetry RF Sensor System using RLS algorithm can be estimated efficiently under noisy environment.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.6
• /
• pp.1051-1057
• /
• 2009

USN(Ubiquitous Sensor Network) is used to provide many services such as bridge monitoring, cultural properties monitoring, river monitoring, protection of an old and feeble person, management and control of a city and circumstance monitoring, etc. A RF transceiver is needed for implementing USN. In this paper the implementation and the design of a RF transceiver for sensor nodes operating in 2.4GHz frequency band are presented. The design procedure of AGC, a receiver and a transmitter is described. And the performance of the implemented RF transceiver is also tested. The test results of receiver sensitivity, receiver dynamic range, frequency stability, phase noise, output power of transmitter, flatness and spectrum mask are presented.

• Journal of the Institute of Convergence Signal Processing
• /
• v.7 no.3
• /
• pp.87-94
• /
• 2006

For realizing an ubiquitous home network(uHome-net), various sensors should be able to be connected to an integrated wire/wireless sensor network. This paper describes an application case of applying LonWorks technology being widely used in control network to wire/wireless sensor network in uHome-net and the design and application of LonRF device that consists of a neuron chip including LonTalk protocol, a 433.92MHz RF transceiver, a sensor, and application programs. As an application example of the LonRF device, the LonRF smart badge that can measure the 3D location of objects in indoor environment and interwork with the uHome-net was developed. LonRF device based home network services were realized on the uHome-net testbed such as indoor positioning service, remote surveillance service and remote metering service were realized. This research shows that LonWorks technology based sensor network could be applicable to the control network in an ubiquitous home network and the LonRF device can be used as a wireless node in various sensor networks.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.06a
• /
• pp.682-684
• /
• 2007

This paper deals the application of sensor network system to fabricate wireless nodes. This node includes a CPLD(XC2C256), FPGA(XC3S1000) a RF module(Bim-433-F), a Hall Sensor and I also develop the CPLD(EPGA) controlling with Verilog-HDL using ISE. The network was consisst of a PC, a Sink node as a gateway, and three Sensor nodes. This sensor network can reaches 40 m with RF interface using by multi-path network.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.10
• /
• pp.1905-1913
• /
• 2006

The researches about the hardware and the software implementing ubiquitous sensor network have great rush in recent years. This paper deals the development of a sensor node with the dual interface which also has an RF wireless interface while has an Bluetooth interface used widely in present. This sensor node includes a Atmeg32 microcontroller, a Bluetooth module, a RF module. a temperature-humidity sensor. and I also develop the F/Ws controlling each modules with C language using GCC compiler. The sensor node developed can reaches 15m with Bluetooth interface and 60m with RF interface. It works stably with the voltage above 5V and it consumes currents 21mA average in idle mode, 63mA average in active mode.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.5
• /
• pp.223-228
• /
• 2018

In this paper the water sensor using a coaxial cavity resonator is designed and manufactured. The water sensor which can sense water drop linearly has been constructed with voltage controlled oscillator(VCO), coaxial cavity resonator, RF switch, RF detector, A/D converter, DAC and micro controller. The operating frequency range of the designed water sensor is from 2.5GHz to 3.2GHz and the input voltage and current source are 24[V/DC] and 1[A]. The designed sensor circuit includes VCO, RF switch, RF detector which varies the frequency characteristics of the devices in the high frequency of 3GHz. And so we should correct the error of the frequency characteristics of those devices in the sensor circuit. To do this, we make the reference path which switches the signals to the RF detector directly without sending it to the resonator. According to the result of simulation and measurement, we can see that there is 0-50MHz difference between simulated resonator frequency and manufactured resonator frequency.

• Journal of Sensor Science and Technology
• /
• v.14 no.3
• /
• pp.150-155
• /
• 2005

We propose a newly developed automobile sensor monitoring system incorporated with a tire pressure monitoring sensor(TPMS). The RF-transmitter based on a tire pressure sensor, sends a frame data about measured tire-pressure to RF receiver. And the various sensing signals based on sensors such as fuel-level sensor, engine oil level sensor and temperature sensors, are converted into 10-bit digital data. The microprocessor displays converting data such as tire pressure, trip distance, fuel quantity, coolant temperature and car-room temperature, on LCD panel. The proposed system can be successfully adapted to monitoring of the tire pressure and various automobile sensors.