• JSTS:Journal of Semiconductor Technology and Science
• /
• v.3 no.2
• /
• pp.89-95
• /
• 2003

In this paper, we have designed and fabricated high conversion gain Q-band active sub-harmonic mixers for a receiver of millimeter wave wireless communication systems. The fabricated active sub-harmonic mixer uses 2nd harmonic signals of a low local oscillator (LO) frequency. The fabricated mixer was successfully integrated by using $0.1{\;}\mu\textrm{m}$GaAs pseudomorphic high electron mobility transistors (PHEMTs) and coplanar waveguide (CPW) structures. From the measurement, it shows that maximum conversion gain of 4.8 dB has obtained at a RF frequency of 40 GHz for 10 dBm LO power of 17.5 GHz. Conversion gain from the fabricated sub-harmonic mixer is one of the best reported thus far. And a phase noise of the 2nd harmonic was obtained -90.23 dBc/Hz at 100 kHz offset. The active sub-harmonic mixer also ensure a high degree of isolations, which are -35.8 dB from LO-to-IF and -40.5 dB from LO-to-RF, respectively, at a LO frequency of 17.5 GHz.

• Journal of Advanced Navigation Technology
• /
• v.16 no.1
• /
• pp.158-162
• /
• 2012

In this paper, we propose a wireless modem, which used OFDM/64QAM method and the ISM band with 2.4GHz radio frequency. In this paper proposed the case of a modem, the main program to process the baseband processor, processing speed, operating voltage, and reliability should be ensured. So we have designed with Ralink's RT2870, witch was used for Wi-Fi solution. The RT2870 provides full support for wireless LAN standard, and supports various modulation formats, 2.4GHz and 5GHz bands, both of which support chip. In this paper, we also output the modulated signal transmitted wirelessly to the 2.4GHz band RF RT2850 chip processing was applied and using 40MHz band 2.422 ~ 2.462GHz wireless bands were designed to occupy. By applying bi-directional transmission between wireless transmitter and receiver, it can be effectively connected with any kinds of wireless LAN with 2.4GHz ISM band. Therefore it could economically be used as peripheral equipments for POS system or personal wireless device based on Android platform.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.4
• /
• pp.453-461
• /
• 2011

In order to use more efficiently limited frequency resources at the broadcasting band and to eliminate blanket area of the terrestrial broadcasting and to improve broadcasting quality. The importance of repeaters has increasing continuously. However, in case of T-DMB digital on channel repeater in OFDM systems, some of the signal radiated feedback again at the receiver antenna. So it generates feedback signal interference in repeater system. Also phase noise increases ICI(Inter Carrier Interference). It affects seriously the frequency domain equalizer. In this paper, we remove the feedback signal interference by LMS with correlation. Also we propose an effective equalizer algorithm that can remove ICI caused by phase noise and the power amplifier's back-off. In this simulation results, this system is satisfied the performance of BER=$10^{-4}$ at less than SNR=14 dB after compensation of phase noise.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.40 no.5
• /
• pp.341-349
• /
• 2003

A real time interactive controller (spectrometer) for magnetic resonance imaging (MRI) system has been developed using high speed digital signal processors (DSP). The controller generates radio frequency (rf) waveforms and audio frequency gradient waveforms and controls multiple receivers for data acquisition. By employing DSPs having high computational power (e.g., TMS320C670l) real time generation of complicated gradient waveforms and interactive control of selection planes are possible, which are important features in real-time imaging of moving organs, e.g., cardiac imaging. The spectrometer was successfully implemented at a 1.5 Tesla whole body MRI system for clinical application. Performance of the spectrometer is verified by various experiments including high- speed imaging such as fast spin echo (FSE) and echo planar imaging (EPI). These high-speed imaging techniques reduce measurement time, however, usually intensify artifact if there is any systematic phase error or jitter in the synchronization between the transmitter, receiver, and gradients.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.10
• /
• pp.19-26
• /
• 1998

In this paper, we studied the design and implementation of fading compensation systems at aspects of narrowband mobile communication using TTIB SSB. The mobile radio channel with multipath fading places fundamental limitations on the performance of wireless communication systems. The multipath fading is compensated using pilot tone in TTIB SSB. The TTIB transceiver was implemented using the prevailing digital signal processing (DSP) techniques and compensation for the multipath fading was incorporated in the receiver in the form of DSP algorithm. In order to evaluate fading compensation performance in TTIB transceiver, we first used computer simulation. In the simulation results, we found that the TTIB transceiver could compensate for the multipath fading as expected. Second, we carried out some experiments on TTIB transceiver implementation with DSP boards and later with hardwares including RF circuits with center frequency of 145MHz. Through these experiments, we found that fading compensation performance in TTIB transceiver was almost as good as that obtained from simulation.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.1
• /
• pp.100-108
• /
• 2014

Low noise amplifier (LNA) is an integral component of RF receiver and frequently required to operate at wide frequency bands for various wireless system applications. For wideband operation, important performance metrics such as voltage gain, return loss, noise figure and linearity have been carefully investigated and characterized for the proposed LNA. An inductive shunt feedback configuration is successfully employed in the input stage of the proposed LNA which incorporates cascaded networks with a peaking inductor in the buffer stage. Design equations for obtaining low and high impedance-matching frequencies are easily derived, leading to a relatively simple method for circuit implementation. Careful theoretical analysis explains that input impedance can be described in the form of second-order frequency response, where poles and zeros are characterized and utilized for realizing the wideband response. Linearity is significantly improved because the inductor located between the gate and the drain decreases the third-order harmonics at the output. Fabricated in $0.18{\mu}m$ CMOS process, the chip area of this wideband LNA is $0.202mm^2$, including pads. Measurement results illustrate that the input return loss shows less than -7 dB, voltage gain greater than 8 dB, and a little high noise figure around 6-8 dB over 1.5 - 13 GHz. In addition, good linearity (IIP3) of 2.5 dBm is achieved at 8 GHz and 14 mA of current is consumed from a 1.8 V supply.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.127-132
• /
• 2006

The Global Positioning System (GPS), Inertial Navigation System (INS) and Pseudolite (PL) technologies all play very important roles in navigation systems. As an independent navigation system, GPS can provide high precision positioning results which are independent of time. However, the performance will become unreliable when the system experiences high dynamics, or when the receiver is exposed to jamming or RF interference. In comparison to GPS, though INS is autonomous and provides good short-term accuracy, its use as a standalone navigation system is limited due to the time-dependent growth of the inertial sensor errors. PLs are ground-based transmitters that can transmit GPS-like signals. They have some advantages in that their positions can be determined precisely, and the Signal-to-Noise Ratios (SNR) are relatively high. Because their combined performance, in principle, overcomes the shortcomings of the individual systems, the integration of GPS, INS and PL is increasingly receiving attention from researchers. Depending on the desired performance vs complexity, system integration can be carried out at different levels, namely loose, tight and ultra-tight coupling. Compared with loose and tight integration, although it is more complex in terms of system design, ultra-tight integration will be the basis of the next generation of reliable and robust navigation systems. Its main advantages include improved performance under exposure to high dynamics, and jamming and RF interference mitigation. This paper presents an overview of the ultra-tight integration developments and discusses some of the challenging issues.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.10A
• /
• pp.922-929
• /
• 2005

This paper proposes an adaptive pilot beacon equipment for mobile communication systems based on direct spread spectrum technology which generates the pilot channel for handoff between base stations by using the information acquired from the downstream wireless signal regarding the overhead channel information. Such an adaptive pilot beacon equipment will enable low power operation since among the wireless signals, only the pilot channel will be generated and transmitted. The pilot channel in the downstream link of the CDMA receiver is used to acquire time and frequency synchronization and this is used to calibrate the offset for the beacon, which implies that time synchronization using GPS is not required and any location where forward receive signal can be received can be used as the installation site. The downstream link pilot signal searching within the CDMA receiver is performed by FPGA and DSP. The FPGA is used to perform the initial synchronization for the pilot searcher and DSP is used to perform the offset correction between beacon clock and base station clock. The CDMA transmitter the adaptive pilot beacon equipment will use the timing offset information in the pilot channel acquired from the CDMA receiver and generate the downstream link pilot signal synchronized to the base station. The intermediate frequency signal is passed through the FIR filter and subsequently upconverted and amplified before being radiated through the antenna.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.3 no.1
• /
• pp.108-118
• /
• 2009

In this paper we develop an indoor location tracking system and its 3D tracking monitoring viewer, viz., 3D Navigation Viewer (3DNV). We focus on the integration of an indoor location tracking system with the Virtual Reality Modeling Language (VRML), to facilitate a representation of the user's spatial information in virtual indoor environments that is synchronized with the physical location environment. The developed indoor location tracking system employs beacons as active transmitters, and a listener as a passive receiver. The distance information calculated from the difference speeds of RF and Ultrasonic signals is exploited, to determine the user's physical location. This is essential in supporting third parties like doctors and caregivers in identifying the activities and status of a particular individual via 3DNV. 3DNV serves as a unified user interface for an indoor location tracking system, showing the viewpoint and position of the target in virtual indoor environments. It was implemented using VRML, to provide an actual real time visualization of the target's spatial information.

• Proceedings of the IEEK Conference
• /
• 2004.08c
• /
• pp.667-670
• /
• 2004

In this paper, we have presented the improved IF transceiver architecture and the implementation and experimental results on re-configurable transceiver based on digital IF for multiple wideband OFDM/TDD base stations for high-speed portable internet-service in which is issued Korea. The implemented IF transceiver has been designed to support multiple frequency allocations and multiple standards by only modifying the programmable software not its hardware like as the software-defined-radio concept. Also, the digital complex quadrature modulation technique has been used for the digital IF transmitter, which is able to combine multiple frequency bands in digital processing block not RF block and to reject the image frequency signals. And the bandpass sampling technique has been used for the digital IF receiver to reduce the sampling rate of ADC. This paper has shown the experiment results on the frequency response and constellation on the base-station implemented using the modified IEEE 802.16a/e physical layer channel structure based on OFDM/TDD.