• Restorative Dentistry and Endodontics
• /
• v.27 no.5
• /
• pp.502-514
• /
• 2002

The aim of this study was to evaluate the marginal adaptation of direct class II sandwich restoration with packable composites(P-60), resin modified glass ionomer cement(Fuji-II LC), flowable compomer(Dyract Flow), flowable composites(Filtek Flow) in comparison with total bond restorations. In addition, for sandwich restorations, influence of different sandwich techniques was also evaluated. Large butt-joint box typed class II cavites with cervical margins 1mm below the cemento-enamel junction were cut into 70 extracted human molars. The cavities(7 groups, n=10) were filled using a closed/open sandwich restoration or total bond restoration technique with materials according to the manufacturer's recommandation using the single-component bonding agent for each system. Teeth were thermocycled 500 times between 5$^{\circ}C$ and 55$^{\circ}C$ with 30-second dwell time. The teeth were then coated with nail polish 1mm short of the restoration, placed in a 2% methylene blue for 24 hours, and sectioned with diamond wheel. Sections were examined with a stereoscope to determine the extent of microleakage. Dentine /Cementum margins were analyzed for microleakage on scale of 0(no leakage) to 4(entire axial wall) and interface between materials, on scale of 0(no leakage) to 3(axial wall). Results were evaluated with Kruskal Wallis Test, corrected for ties, to determine whether there were statistically significant differences among the seven groups. Pairs of groups were analyzed using the Student-Newman-Keuls Method and Dunn s Method. The results were as follows : 1. All groups showed some micoleakage in cervical portion. But there were no microleakage in interface between materials. 2. Closed sandwich restorations with Fuji-II LC and Filtek Flow had significantly lower leakage rating than total restorations with only P-60. However, open sandwich restorations with Dyract Flow showed significantly higher (P<0.05) 3. Closed sandwich restorations had significantly lower leakage rating than total restorations. However open sandwich restoration s showed significantly higher (P<0.05). 4. Sandwich restorations with Fuji-II LC were iou$.$or leakage than only P-60. Filtek Flow, Dyract Flow. But there were no statistically differences among the materials. From the results above, it could be concluded, closed sandwich restorations was effective in reducing microleakage of class II restorations. The best results showing the least microleakage were for the closed sandwich technique with Fuji-II LC and Filtek Flow.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.51 no.5
• /
• pp.217-224
• /
• 2002

This paper presents an algorithm to obtain an approximate optimal solution for the service restoration and load balancing of large scale radial distribution system in a real-time operation environment. Since the problem is formulated as a combinatorial optimization problem, it is difficult to solve a large-scale combinatorial optimization problem accurately within the reasonable computation time. Therefore, in order to find an approximate optimal solution quickly, the authors proposed an algorithm which combines optimization technique called cyclic best-first search with heuristic based feeder loadings balance index for computational efficiency and robust performance. To demonstrate the validity of the proposed algorithm, numerical calculations are carried out the KEPCO's 108 bus distribution system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.540-545
• /
• 1997

This paper is to evaluate the stress distibution and displacements around the single implant restoration in dentisry. The computer simulation technique using FEM was applied to the analysis, and four londing inclination were studied: verical(0 .deg.),15 .deg.,30 .deg.,45 .deg. with respect to implant axis. The magnitudes of occlusal force were 100N, 200N, 300N, 400N, and 500N. The computed result shows that the stress on a single implant restoration increases as the load or the inclined angel increases, and that the change in loading inclination has a greater effect on the stress distribution than that of the load magnitude.

• Journal of the Korean Society of Safety
• /
• v.20 no.1 s.69
• /
• pp.7-12
• /
• 2005

In heavy industrial fields such as power plant and chemical plant, it is often necessary to restore a damaged part of large machinery or structure which is installed in the hazard working place. In this paper, to evaluate the safety of plastic deformed cylindrical beam a finite element technique has been used. The variations of residual stresses on the process of damaging and restoring for surfaces and cross-sections have been examined. The results show that the maximum von Mises stresses occur outer cylinder surfaces of boundary between cylindrical beam support md cylindrical beam when deformation procedure and restoring force is applied. The maximum residual stress remains 158.6MPa in the inner wall and this value correspond to $53\%$ of yield stress then restoration procedure is finished.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.52 no.9
• /
• pp.513-520
• /
• 2003

Service restoration is an emergency control in distribution constrol centers to restore out-of-service area as soon as possible when a fault occurs in distribution networks. therefore, it requires fast computation time and high quality solutions for load balancing. In this paper. a load balance index and heuristic guided best-first search are proposed for these problem. The proposed algorithm consists of two parts. One is to set up a decision tree to represent the various switching operations available. Another is to identify the most effective the set of switches using proposed search technique and a load balance index. Test results on the KEPCO's 108 bus distribution system show that the performance is efficient and robust.

• The Journal of the Korean dental association
• /
• v.49 no.2
• /
• pp.85-94
• /
• 2011

In the filed of Dentistry, minimally invasive treatment modalities are new trend for conservation of natural teeth. Of them, laminate veneer and resin bonded fixed partial denture belong to restoration procedures. In this review, survival rates of each modalities and cause of unserviceability are analyzed, and criteria for success are presented. To get successful results of minimally invasive restoration, plenty of enamel layer, thin and strong materials, and high bonding strength are essential under cyclically loaded wet oral condition. Newly tried design of minimally invasive technique nowadays have to be evaluated only on the basis of requirement for long-term success.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.9 no.5
• /
• pp.10-21
• /
• 2006

For analyze of the bearing capacity, skin friction and settlements of pile on axial compressive loading, both Load transfer tests of pile and pile loading test in field have application to commonly before pile installing. A bearing capacity of pile was affected by the characteristics of surrounding ground of pile. Especially, that is very different because of evaluation of settlement due to each soil conditions of ground depths. The ground characteristics using evaluation of bearing capacity of pile through load transfer analysis depends on N values of SPT, and then a bearing capacity of pile installed soft ground and refilled area may be difficult to rational evaluation. An evaluation of bearing capacity on pile applied axial compressive loading was effected by strength of ground installed pile, unconfined compressive strength at pile tip, pile diameter, rough of excavated surface, confining pressure and deformation modules of rock etc and these are commonly including the unreliability due to slime occurred excavation works. Load transfer characteristics considered ground conditions take charge of load transfer of large diameter pile was investigated through case study applied load transfer tests. To these, matrix analytical technique of load transfer using finite differential equation developed and compared with the results of pile load test.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.4
• /
• pp.67-77
• /
• 1995

In modern industry the requirement of automation of manufacturing process increases so that unmanned system has been popular as an ultimate goal of modern manufacturing process. In unmanned manufacturing process the tool fracture is a very serious problem because it results in the damage of workpieces and can stop the operation of whole manufa- turing system. In this study, image processing technique is used to detect the fracture of insert tip of face milling using multi-point-tool. In order to acquire the image information of fracture shape of rotation insert tip. We set up the optical system using a light beam chopper. In this system we can reduce the image degradation generated from stopped image of rotating insert tip using image restoration technique. We calculated the mean square error to diagnose the condition of tool fracture, and determind the criteria of tool fracture using experimental and staticstical method. From the results of this study we've developed non- contact detection technique of tool fracture using image processing method and proposed the fracture direction of automation and unmanned system considering the optimal time of tool change milling.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.6
• /
• pp.56-62
• /
• 2014

This study aims to investigate the applicability of supercritical fluid extraction as a dewaxing technique to restore the beeswax-treated volume of the Annals of the Joseon Dynasty in various deterioration and damage conditions. Thus, this study analyzed the dewaxing efficiency and changes in physical and morphological properties before and after dewaxing, by applying the optimal supercritical fluid extraction dewaxing condition ($70^{\circ}C$, 40 MPa, $CO_2$, Co-solvent 20% DCM, 2 hour) to 3 kinds of beeswax-treated paper with different deterioration rates (dry artificial aging of 10, 20 and 30 days at $120^{\circ}C$). After dry artificial aging at $120^{\circ}C$ for 30 days, the average molecular weight of the beeswax-treated specimen was $1.856{\times}10^5g/mol$, showing deterioration about 80% of the beeswax-treated paper before dewaxing. It was a similar level to the molecular weight of the bees-waxed volume of the Annals of the Joseon Dynasty that has a higher degree of damage. As a result of analyzing the dewaxing efficiency through FT-IR analysis, this study discovered that it was possible to effectively dewax beeswax-treated paper in the range of deterioration 20 to 80% with this supercritical fluid extraction dewaxing technique applied. As a result of analyzing changes in the physical and morphological properties before and after dewaxing, the viscosity tended to decrease to a slight degree, and since no morphological deformation or damage of stencil fibers was found, it was concluded possible to conduct stable dewaxing through this supercritical fluid extraction technique.

• Journal of Conservation Science
• /
• v.30 no.3
• /
• pp.307-315
• /
• 2014

The gold textile is Korean traditional weaving technique using the gold thread since 5th century. The making technique of gold thread was written in various references, but it is severed because the gold thread weaving equipment and sumptuous moods were forbidden in the early 18th century. There are some studies of traditional gold thread which are mainly about conservation treatment of cleaning and strength. To restore traditional gold thread, investigation of material and manufacturing technique is vitally required. The gold threads are composed of gold leaf, adhesive and base sheet. Gold leaf and base sheet are available for investigation because they are exposed to the surface, whereas adhesive is not easy to investigate because it is not exposed to the surface. In this study, samples are made of pure and impure gold, animal glue and lacquer, and various types of Hanji based on domestic and foreign references to compare materials for gold threads. As a result of morphological character and stability evaluation, the optimum materials for the restoration of gold threads are pure gold, animal glue and Dochimji(smoothing paper by beating). This study is expected to be basic data for manufacturing gold threads techniques and modernization of traditional gold threads hereafter research.