• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.8
• /
• pp.692-700
• /
• 2001

Flow boiling heat transfer coefficients(HTCs) of R22, R134a, R407C, and R410A were measured experimentally for a horizontal plain and a microfin tube. Experimental apparatus was composed of 3 main parts: a refrigerant loop, a water loop and a water-glycol loop. The test section in th refrigerant loop was made of a copper tube of 9.52 mm outer diameter and 1 m length for both tubes. The refrigerant was heated by passing hot water through an annulus surrounding the test section. Tests were performed at a fixed refrigerant saturation temperature of $5^{\circ}C$ with mass fluxes of 100~300 kg/$m^2$s. Test results showed that at similar mass flux the flow boiling HTCs of R134a were similar to those of R22 for both plain and microfin tube. HTCs of R407C were similar to those of R22 for a plain tube but lower than those of R2 by 25~48% for a microfin tube. And HTCs of R410A were higher than those of R2 by 20~63% for a plain tube and were similar to those of R22 for a microfin tube. In general, HTCs of a microfin tube were 1.8~5.7 times higher than those of a plain tube.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.7
• /
• pp.595-603
• /
• 2003

R407C is considered as an alternative refrigerant to R22 for air conditioners. An experimental investigation was made to study the characteristics of the condensation heat transfer and pressure drop for R407C flowing in a fin-and-tube heat exchanger used for commercial air-conditioning units. Experiments were carried out under the conditions of inlet refrigerant temperature of 6$0^{\circ}C$ and refrigerant mass flux varying from 150 to 250 kg/$m^2$s for refrigerant side. The inlet air has dry bulb temperature of 35$^{\circ}C$ , relative humidity of 50% and air velocity varying from 0.8 to 1.6 m/s. Experiments show that air velocity increased by 25% is needed for R407C than that of R22 for subcooling temperature of 5$^{\circ}C$, which resulted in air-side pressure drop increase of 28.8% for R407C as compared to R22. As a consequence, in order to provide the same design condition of a condenser, the fan requires higher electric-power consumption with R407C than that with R22.

• Asian-Australasian Journal of Animal Sciences
• /
• v.13 no.12
• /
• pp.1681-1690
• /
• 2000

A study on energy and protein utilization, and milk production of Bali cows on grass-legume diets was carried out using 12 first lactation cows (initial BW $263.79{\pm}21.66kg$) during a period of 16 weeks starting immediately post calving. The animals were randomly allotted into 4 dietary treatment groups R1, R2, R3 and R4, receiving from the last 2 months of pregnancy onwards, graded improved rations based on a mixture of locally available grass and legume feed ad libitum. R1 contained on a DM basis 70% elephant grass (PP, Penisetum purpureum) plus 30% Gliricidia sepia leaves (GS), R2 was 30% PP plus 55% GS supplemented with 15% Hibiscus tilliactus leaves (HT, defaunating effect), R3 and R4 were 22.5% PP+41.25% GS+11.25% HT+25% concentrate, where R3 was not and R4 supplemented with zinc di-acetate. TDN, CP and zinc contents of the diets were 58.2%, 12.05% and 18.3 mg/kg respectively for R1, 65.05%, 16.9% and 25.6 mg/kg respectively for R2, 66.03%, 16.71% and 29.02 mg/kg respectively for R3 and 66.03%, 16.71% and 60.47 mg/kg respectively for R4. Milk production and body weight were monitored throughout the experimental period. In vivo body composition by the urea space technique validated by the body density method and supported by carcass data was estimated at the start and termination of the experiment. Nutrient balance and rumen performance characteristics were measured during a balance trial of 7 days during the 3rd and 4th week of the lactation period. Results indicated that quality of ration caused improvement of ruminal total VFA concentration, increments being 52 to 65% for R2, R3 and R4 above R1, with increments of acetate being less (31 to 48%) and propionate being proportionally more in comparison to total VFA increments. Similarly, ammonia concentrations increased to 5.24 to 7.07 mM, equivalent to 7.34 to 9.90 mg $NH_3-N/100ml$ rumen fluid. Results also indicated that feed quality did not affect DE and ME intakes, and heat production (HP), but increased GE, UE, energy in milk and total retained energy (RE total) in body tissues and milk. Intake-, digestible- and catabolized-protein, and retained-protein in body tissues and milk (Rprot) were all elevated increasing the quality of ration. Similar results were obtained for milk yield and components with mean values reaching 2.085 kg/d (R4) versus 0.92 kg/d (R1) for milk yield, and 170.22 g/d (R4) vs 71.69 g/d (R1), 105.74 g/d (R4) vs 45.35 g/d (R1), 101.34 g/d (R4) vs 46.36 g/d (R1) for milk-fat, -protein, and -lactose, respectively. Relatively high yields of milk production was maintained longer for R4 as compared to the other treatment groups. There were no significant effects on body mass and components due to lactation. From the relationship $RE_{total}$ (MJ/d)=12.79-0.373 ME (MJ/d); (r=0.73), it was found that $ME_{m}=0.53MJ/kgW^{0.75}.d$. Requirement of energy to support the production of milk, ranging from 0.5 to 3.0 kg/d, follows the equation: Milk Prod. ($Q_{mp}$, kg/d)=[-2.48+4.31 ME($MJ/kg^{0.75}.d$)]; (r=0.6) or $Q_{mp}$=-3.4+[0.08($ME-RE_{body\;tissue}$)]MJ/d]; (r=0.94). The requirement for protein intake for maintenance ($IP_m$) equals $6.19 g/kg^{0.75}.d$ derived from the relationship RP=-47.4+0.12 IP; (r=0.74, n=9). Equation for protein requirement for lactation is $Q_{nl}$=[($Q_{mp}$)(% protein in milk)($I_{mp}$)]/100, where $Q_{nl}$ is g protein required for lactation, $Q_{mp}$ is daily milk yield, Bali cow's milk-protein content av. 5.04%, and $I_{mp}$ is metabolic increment for milk production ($ME_{lakt}/ME_{m}=1.46$).

• The Korean Journal of Physiology and Pharmacology
• /
• v.7 no.6
• /
• pp.303-306
• /
• 2003

Metabotropic glutamate receptors (mGluRs), classified into three groups (group I, II, III), play a critical role in modulation of synaptic transmission at central and peripheral synapses. In the present study, extracellular field potential recording techniques were used to investigate effects of mGluR agonists on excitatory synaptic transmission at thalamic input synapses onto the lateral amygdala. The non-selective mGluR agonist t-ACPD ($100{\mu}M$) produced reversible, short-term depression, but the group III mGluR agonist L-AP4 ($50{\mu}M$) did not have any significant effects on amygdala synaptic transmission, suggesting that group I and/or II mGluRs are involved in the modulation by t-ACPD. The group I mGluR agonist DHPG ($100{\mu}M$) produced reversible inhibition as did t-ACPD. Unexpectedly, the group II mGluR agonist LCCG-1 ($10{\mu}M$) induced long-term as well as short-term depression. Thus, our data suggest that activation of group I or II mGluRs produces short-term, reversible depression of excitatory synaptic transmission at thalamic input synapses onto the lateral amygdala. Considering the long-term effect upon activation of group II mGluRs, lack of long-term effects upon activation of group I and II mGluRs may indicate a possible cross-talk among different groups of mGluRs.

• The Journal of Korean Academy of Prosthodontics
• /
• v.46 no.1
• /
• pp.12-21
• /
• 2008

Statement of problem: There have been many studies about marginal adaptation of Zirconia core fabricated with various CAD/CAM systems. But, the comparative study has not been conducted much. Purpose: This study was to compare marginal adaptations of zirconia cores fabricated with 3 different CAD/CAM systems. Material and methods: The in vitro marginal adaptations of zirconia cores fabricated with 3 different CAD/CAM systems($Adens^{(R)}$ system, $Lava^{(R)}$ system, and $Cerasys^{(R)}$ system) were evaluated and compared. In this study 30 zirconia cores were fabricated(10 zirconia cores per each system). The measurements of the marginal adaptatioin were carried out using microscope $L-150A^{(R)}$(Nikon, Japan). Measurements were recorded at 50 points. The measurements were analyzed using Kruskal-Wallis test and Wilcoxon rank sum test. Results: Within the limits of this study, the results were as follows. 1. Mean marginal gap values obtained were $284.5{\pm}152.9{\mu}m$ in Adens system, $99.0{\pm}73.0{\mu}m$ in Lava system, and $153.5{\pm}85.7{\mu}m$ in Cerasys system. 2. Zirconia core made by Lava system showed the smallest marginal gap(P<0.05). Conclusion: In the limitation of this study, we concluded that $Lava^{(R)}$ System was superior than other systems($Adens^{(R)}$ system and $Cerasys^{(R)}$ system) in the marginal adaptation.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.34 no.4
• /
• pp.378-383
• /
• 1989

For selection of mutants two rice varieties, Sangpungbyeo and Seomjinbyeo, were irradiated with 20 kR and 25 kR of gamma rays. One panicle per each plant was harvested in Ml, and single needling per hill was planted for M2 and M3 generations. Mutations for short culm, earliness and the major traits were examined. 1. The mutation rates were varied with the rice varieties and the doses of radiation, higher in Sangpungbyeo and 25kR than in Seomjinbyeo and 20 kR, respectively. 2. The rates in Sangpungbyeo with the 20 kR and 25 kR were 1.10％ and 1.47％. respectively and those of Seomjinbyeo were 0.51％ and 1.25％, respectively. 3. The culm lengths of short-culm mutants derived from Sangpungbyeo and Seomjinbyeo were reduced about 10％ compared to their mother varieties, especially it was possible to select the dwarf mutants reducing 57％ and 40％ of culm length in Sangpungbyeo and Seomjinbyeo, respectively with the dose of 25 kR irradiation. 4. The range of heading date of the mutant ion in the M3 generation was comparatively wide. Many earliness mutants shortened about 7 days were selected as compared with their mother varieties, some mutants of the irradiated group had early matured by 20 days and 30 days, respectively in both Seomjinbyeo and Sangpungbyeo.

• The Journal of Korean Academy of Prosthodontics
• /
• v.40 no.6
• /
• pp.545-559
• /
• 2002

There has been increasing use of IPS Empress $2^{(R)}$ owing to easy fabrication method, high esthetics similar to natural teeth, good marginal accuracy, and sufficient fracture strength. However, in clinical application, although a luting agent and the tooth cementation bonding procedure influence the marginal accuracy and fracture strength restoration, there has been a controversy in the selection of proper luting agent. This study was to measure the marginal fidelites and fracture strength of IPS Empress crowns according to three cement types, Protec $cem^{(R)}$, Variolink $II^{(R)}$ and Panavia $21^{(R)}$. After construction of 12 experimental dies for each group, IPS Empress $2^{(R)}$ crowns were fabricated and luted the metal master die prepartion of the maxillary right premolar. Marginal gaps before cementation and after cementation were measured. Buccal incline on the functional cusp of specimens were loaded until the catastrophic failure and fracture strength was measured. The results of this study were as follows: 1. The range of gap was $34.04{\pm}4.84{\mu}m$ before cementation and $37.88{\pm}5.00{\mu}m$ after cementation, which showed significant difference by paired t-test (p<0.05). The difference in the results from marginal accuracy according to measuring point proved to be not statistically significant by two-way ANOVA test (p>0.05). 2. The difference in the results from marginal accuracy according to three cement types Proved that The Variolink $II^{(R)}$ cement group had the least gap, $35.43{\pm}5.03{\mu}m$, and showed superior marginal accuracy while there existed statistic significance in Protec $cem^{(R)}$ cement group, $39.06{\pm}4.41{\mu}m$ or Panavia $21^{(R)}$ cement group, $39.16{\pm}4.39{\mu}m$ by two-way ANOVA test & multiple range test (p<0.05). 3. The difference in the results from fractures strength testing according to three cement type groups proved to be statistically significant (p<0.05). The Variolink $II^{(R)}$ cement group shows highest fracture strength of $1257.33{\pm}226.77N$, Panavia $21^{(R)}$ cement group has $1098.08{\pm}138.45N$, and Protec $cem^{(R)}$ cement group represents the lowest fracture strength of $926.75{\pm}115.75N$. 4. Three different cement groups of different components showed acceptable marginal fidelity and fracture strength. It is concluded that IPS Empress $2^{(R)}$ crowns luted using Variolink $II^{(R)}$ cement group had stronger fracture strength and smaller marginal gap than the other cement groups. Although Variolink $II^{(R)}$ resin cement seemed acceptable to clinical applications in IPS Empress $2^{(R)}$ system, the IPS Empress $2^{(R)}$ system still requires long-term research due to the lack of data in clinical applications.

• The Korean Journal of Mycology
• /
• v.21 no.1
• /
• pp.16-22
• /
• 1993

Morphological and cultural characteristics of fungi causing rice sclerotial diseases were examined. Hyphal widths of R. solani and R. oryzae were same and ranged $6.0-12.0\;{\mu}m$ with average $9.0\;{\mu}m$, the widest among those of the sclerotial fungi examined. Hyphal width of R. oryzae sativae ranged $6.0-9.0{\mu}m$ with average $7.4{\mu}m$. Hyphal width of R. cerealis was the narrowest among those of Rhizoctonia species examined, and the same was hyphal width of S. oryzae among those of Sclerotium species. Nuclear staining by HCL-Giemsa method showed that R. solani and R. oryzae had many nuclei within one hyphal cell, S. oryzae one nucleus, and the other sclerotial fungi mostly two nuclei. The nuclear number of R. solani was the largest, which ranged 2-17 with average 6.3. Average size of sclerotia of the sclerotial fungi except S. hydrophilum and S. oryzae produced in lesions ranged 1.0-2.0mm. Average size of sclerotia of S. hydrophilum and S. oryzae was 0.5mm and 0.24mm, respectively. Sclerotia of R. solani and R. oryzae produced in culture were more variable in size and larger than those produced in lesions. However, the sclerotial sizes of the other sclerotial fungi produced in culture were almost the same as those produced in lesions. Sclerotial colors of sclerotial fungi produced in lesions were similar to those produced in culture, but sclerotial shapes of some sclerotial fungi exhibited somewhat difference between the sclerotia produced in lesions and in culture. Optimum temperature for mycelial growth of R. cerealis was $23^{\circ}C$, and that of the other sclerotial fungi ranged from $27\;to\;33^{\circ}C$. Maximum temperature for mycelial growth of some sclerotial fungi was as high as $41^{\circ}C$, while that of R. cerealis was as low as $31^{\circ}C$. Minimum temperature for mycelial growth of R. cerealis was $2^{\circ}C$, and that of the other sclerotial fungi ranged from $6\;to\;10^{\circ}C$.

• Journal of Microbiology and Biotechnology
• /
• v.20 no.1
• /
• pp.30-38
• /
• 2010

The contribution of a type II restriction-modification system (R-M system) to genome integrity and cell viability was investigated. We established experimental conditions that enabled the achievement of hemimethylated and unmethylated states for the specific bases of the recognition sequences of the host's DNA. To achieve this, we constructed the MboII R-M system containing only one (i.e., M2.MboII) out of two functional MboII methyltransferases found in Moraxella bovis. Using the incomplete R-M system, we were able to perturb the balance between methylation and restriction in an inducible manner. We demonstrate that upon the SOS-induced DNA repair in mitomycin C treated cells, restriction significantly reduces cell viability. Similar results for the well-studied wild-type EcoRI R-M system, expressed constitutively in Escherichia coli, were obtained. Our data provide further insights into the benefits and disadvantages of maintaining of a type II R-M system, highlighting its impact on host cell fitness.

• Elastomers and Composites
• /
• v.29 no.1
• /
• pp.18-29
• /
• 1994

The purpose of this study is to investigate reinforced effect between silica treated by coupling agents and rubber matrix under the configuration chemical bonds, and the effect of silica particles coated by organic polymers using aluminum chloride as the catalyst. In vulcanization characteristies were tested by Curastometer. The M-series vulcanizates were reached to the fastest optimum cure $time(t_{90})$ and R-series vulcanizates with the same formula had the shorted optimum cure times. Tensile characteristics measuring with a tensile tester revealed that the M-series vulcanizate was the best in the physical properties, such as tensile strength. In 100% modulus, however, the S-series vulcanizates appeared to be better than the other vulcanizates. Also, hardness showed the following order : S-series>R-series>M-series with the order of elongation R-series>M-series>S-series. In SEM test, shapes of chemical treated silicas were observed. The dispersion of filler in the SBR composite appeard uniformly. In RDS test for the dynamic characteristics, G' indicates that S-3 shows the highest value with the next order M-3>R-3, and the order of damping values are as followe: M-3>M-3>R-3.