• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.16 no.9
• /
• pp.862-876
• /
• 1991

In this theses, the procedure for finding the equivalent immittance of an n-line coupled structures is presented in terms of the normal mode parameters of the n-line coupled system. The above generalized equations can be applied to the various Coupled structures including directional couplers, DC blocks, bandpass/band elimination filters, and various other uniformly coupled filters. The design equations are based on a simplified TEM(Quasi TEM) mode. The obtained results and the definition of the scattering parameters for a general coupled line four port with arbitrary terminations are used to present the procedure to determine the optimum physical dimensions matching the given load impedances connected to input, output port. Multiple coupled rnicrostrip two-port with three lines circuit designed shows little discrepancy between the conventional method and this one. Four port with five lines were fabricated on teflon substrate($e$r=2.55) with its thickness h=l.588mm designed at the center frequency, 4 GHz. Their measured results are fairly close to the ones by computation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.8
• /
• pp.1173-1182
• /
• 2001

Recent noticeable advances of CNC machine tools have considerably improved productivity and precision in manufacturing processes. However, in the respect of productivity some defects still remain because selection of machining conditions entirely depends on the experiences of programmers. Usually, machining conditions such as feed rate and spindle speed have been selected conservatively by considering the worst cases, and it has brought the loss of machining efficiency. Thus, the improvement of cutting force controller has been done to regulate cutting force constantly and to maximize feedrate simultaneously in case that machining conditions change variously. In this study, sliding mode control with boundary layer is applied to milling process for cutting force regulation and in a commercial CNC machining center data transfer between PC and PMC (programmable machine controller) of CNC machine is done using a standard interface method. And in the cutting force measurement, an indirect cutting force measuring system using current signal of AC servo is adopted in order not to use high-priced equipment like tool dynamometer. The purpose of this study is to maximize the productivity in milling process, thus its results can be applied to cases such as rough cutting process.

• Journal of Internet Computing and Services
• /
• v.12 no.3
• /
• pp.111-117
• /
• 2011

In this paper, the BER(Bit Error Rate) performance of a DVB-T2(Second Generation Digital Terrestrial Television Broadcasting System) in MISO(Multiple Input Single Output) transmission mode is evaluated by the computer simulation. In the DVB-T2 receiver, an IDD(Iterative Demapping and Decoder) technique is employed that exchanges extrinsic information between the demapper and the LDPC decoder. Simulation results show that the IDD-based DVB-T2 receiver in MISO transmission mode provides 2dB gain at BER of $10^{-4}$ but suffer from the frequency offsets between transmit antennas.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.387-388
• /
• 2006

This article provides a dynamic analysis model for huge marine engine that examined analytically variation effects of frequency response by fitting of transverse stays such as hydraulic type. First, vibration analysis using the three dimensional finite element models for the huge marine engine has performed in order to find out the dynamic characteristics. Second, three dimensional finite elements model for the huge marine engine was modifued so that generate forcing nodes in crosshead part and top bracing nodes in cylinder frame part. Third, a system matrix and output matrix was derived for the general siso(single input single out) state space model. Finally, developed state space model for the three dimensional finite elements model for the huge marine engine without the additional modifying process.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.3
• /
• pp.511-519
• /
• 2016

This paper is proposed control algorithm for the using thyristor of the parallel dual converter for Urban railway power supply in order to return the regenerative power generated by regenerative braking in urban railway train. Conventional control algorithm of Thyristor dual converter for urban railway power supply has voltage variation within a control range of hysteresis band. The purposed control algorithm of the parallel thyristor dual converter is to maintain a constant voltage without voltage variation in accordance with variable load through the Sequential mode change. And the control algorithm need calculating optimum initial firing angle to consider magnitude of the load current slope. For this purpose, Proposed algorithm for sequential conversion mode of the dual converter was verified by applying for the simulation.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.2
• /
• pp.118-126
• /
• 2020

A solar array simulator is a special power supply that regulates the output voltage and current to simulate the characteristics of a photovoltaic panel. The operating point of the panel is difficult to control with a single controller because of the non-linearity of the output curve, which is determined by the amount of irradiation, temperature, and panel material. In the conventional method, the output curve is divided into sections through the current and the voltage mode controls. It reduces the overall performance of the system due to the interchanging control mode. By using the single mode controller, the noise interference of the measured value and the stability of the control around the maximum power point were demonstrated. To solve these issues, this study proposes a new unified controller. The stability of the controller was analyzed along with operating principles, and performance improvement was experimentally verified.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.3
• /
• pp.82-87
• /
• 2013

In this work, the 1L grade integrated metal DOC/DPF filter that can install in engine manifold position was developed to investigate the effect of platinum-coating amount of filter on the improvement of filter activation temperature and reduction of particulate matter (PM). This filter was installed in 2.9L CI engine which meets the EURO-4 emission regulation. Tests for PM reduction efficiency of filter were conducted under ND-13 mode with full-load test condition. It was revealed that the time to reach the activation temperature of metal filter ($280^{\circ}C$) was shorter as the amount of platinum-coating increased. This short activation time can be helpful for the reduction of CO and HC emissions during cold start condition. At the same time, PM reduced as the coating amount increased. The reduction percentage of $DOC_{40}$, $DOC_{20}$, and $DOC_0$ were 96.7% (2.34 mg/kW'h), 95.1% (3.47 mg/kW'h), and 94.5% (3.69 mg/kW'h) compared to previous result (71.4 mg/kW'h), respectively.

• Nuclear Engineering and Technology
• /
• v.45 no.3
• /
• pp.323-334
• /
• 2013

During a hypothetical core-disruptive accident (CDA) in a sodium-cooled fast reactor (SFR), degraded core materials can form roughly conically-shaped debris beds over the core-support structure and/or in the lower inlet plenum of the reactor vessel from rapid quenching and fragmentation of the core material pool. However, coolant boiling may ultimately lead to leveling of the debris bed, which is crucial to the relocation of the molten core and heat-removal capability of the debris bed. To clarify the mechanisms underlying this self-leveling behavior, a large number of experiments were performed within a variety of conditions in recent years, under the constructive collaboration between the Japan Atomic Energy Agency (JAEA) and Kyushu University (Japan). The present contribution synthesizes and gives detailed comparative analyses of those experiments. Effects of various experimental parameters that may have potential influence on the leveling process, such as boiling mode, particle size, particle density, particle shape, bubbling rate, water depth and column geometry, were investigated, thus giving a large palette of favorable data for the better understanding of CDAs, and improved verifications of computer models developed in advanced fast reactor safety analysis codes.

• Proceedings of the Korea Society for Industrial Systems Conference
• /
• 2000.11a
• /
• pp.333-351
• /
• 2000

In this paper, for DBR scheduler development I have designed prototype by using methodology and gave you some research about system integration to apply DBR sch onto the plan establishment phase of SNS system. DBR manage the constraints and the working speed of each product resource t frequently and today its role is tend to be much expanded by inserting mode information system such as MRPⅡ, ERP and SCM. So in this paper I have analyzed designed the business and inner processor for DBR scheduler development then on t of the analyzed data I have developed the simulator And moreover I will suggest method to insert it into SNS system modules. For system development I have used Delphi 4.0, Microsoft Access(DBMS) and QuickR for making report such as ordering, working directions, progress chart and inventor

• Journal of IKEEE
• /
• v.26 no.2
• /
• pp.249-256
• /
• 2022

The prosthetic leg is a device that performs walking instead of a amputated lower limb, and require a change in locomotion mode by providing the user's intention to respond to a discontinuous locomotion environment. Research has been conducted to detect the users' intentions through biomechanical features inside the socket that directly contacts the cut site in demand for natural locomotion mode changes without external control equipment. However, there is still a need for a sensor system that is suitable for the internal environment of the main body and socket of the cut site. Accordingly, this paper proposed a film-type sensor system that is suitable for the main body characteristics of the cut site, is not affected by the temperature and humidity conditions inside the socket, and is easy to manufacture in various sizes. The proposed sensor is manufactured base on Velostat film and takes into account the pressure measurement characteristics that vary with size. Through the experiment, the change in the internal pressure of the socket due to the intentional posture performance of the wearer was measured, and the possibility of detecting the intention to change the locomotion mode was confirmed.