• Progress in Superconductivity
• /
• 제1권1호
• /
• pp.9-13
• /
• 1999

The influence of quenching temperature and annealing time on superconducting characteristics has been investigated for a $(Pb_{0.6}V_{0.4})Sr_2(Ca_{0.65}Er_{0.35})Cu_2O_z$ compound. From the resistivity measurements for samples annealed at $400^{\circ}C$ to $860^{\circ}C$ in oxygen and subsequently quenched, it is observed that $T_c$(zero) of the sample decreases with the increase of annealing temperature up to $600^{\circ}C$ and increases again beyond $700^{\circ}C$. Annealings of the sample at $860^{\circ}C$ show that $T_c$(zero) goes through a maximum of 62K with the increase of the annealing time. It is also found that $T_c$(zero) of the sample quenched from high temperature decreases when the sample is subjected to low temperature annealing below. $600^{\circ}C$ in oxygen. The experimental results indicate that the as-prepared samples contain excessive oxygen and removal of this excessive oxygen in as-prepared samples is a key factor in controlling the superconducting properties of the samples and are discussed in connection with thermal gravimetric measurements.

• 한국세라믹학회지
• /
• 제34권7호
• /
• pp.767-773
• /
• 1997

Thermal shock behavior of alumina ceramics were studied by quenching the heated alumina specimen into the water of various temperatures over 0~10$0^{\circ}C$. The critical thermal shock temperature difference ( Tc) of the specimen decreased almost linearly from 275$^{\circ}C$ to 20$0^{\circ}C$ with increase in the cooling water temperature over 0~6$0^{\circ}C$. It is probably due to the increase of the maximum cooling rate which is dependent of the convection heat transfer coefficient. The convection heat transfer coefficient is a function of the temperature of the cooling water. However, the critical thermal shock temperature difference( Tc) of the specimen increased at 25$0^{\circ}C$ over 80~10$0^{\circ}C$ due to the film boiling of the cooling water. The maximum cooling rate, which brings about the maximum thermal stress of the specimen in the cooling process, was observed to increase linearly with the increase in the quenching temperature difference of the specimen due to the linear relationship of the convection heat transfer coefficient with the water temperature over 0~6$0^{\circ}C$. The critical maximum cooling rate for thermal shock fracture was observed almost constant to be about 260$\pm$1$0^{\circ}C$/s for all water temperatures over 0~6$0^{\circ}C$. Therefore, thermal shock behavior of alumina ceramics is greatly influenced by the convection heat transfer coefficient of the cooling water.

• Transactions on Electrical and Electronic Materials
• /
• 제1권3호
• /
• pp.6-9
• /
• 2000

Selectively excited photoluminescence(PL) spectroscopy has been carried out on the ~1540 nm $^{4}$I$_{13}$ 3/ to $^{4}$I/wub 15/2/ emissions of the multiple Er$^{3+}$ centers observed in Er-implante undoped and Mg-doped GAN at temperatures ranging from 6K to 295K. The temperature dependence of the Er$^{3+}$ PL spectra selectively excited by below -gap light demonstrates different quenching rates for the distinct Er$^{3+}$ centers, and indicates that the PL spectra with the most rapid thermal quenching rats do not contribute to the room temperature, above-p-pumped Er$^{3+}$ spectrum. In addition, selective PL spectroscopy has ben carried out on the Er$^{3+}$ emission in Er-implanted undoped and Mg-doped GaN at temperatures ranging 6K to 295K. The results indicate that the previously reported enhancement of the violet-pumped centers contribution to the low temperature above excited Er$^{3+}$ PL in Mg-doped GaN is also evident at room temperature.temperature.

• 열처리공학회지
• /
• 제24권6호
• /
• pp.327-337
• /
• 2011

Effects of microstructural change, tensile properties and impact property according to the change of austenitizing temperature and tempering temperature of AISI 51B20 steel were examined. Regardless of austenite grain size, lath martensite with needle and packet shapes was found at tempering temperature of $300^{\circ}C{\sim}400^{\circ}C$. The needles of lath martensite changed to parallel packet at tempering temperature of $450^{\circ}C{\sim}600^{\circ}C$. As tempering temperature increased, tensile strength, yield strength and hardness decreased, while elongation, ratio of reduction area and Charpy impact energy increased. Grain size increased when quenching temperature was $930^{\circ}C$. Grain size had prominent effect on the mechanical properties of AISI 51B20 steel. Ratio of tensile strength/yield strength and yield strength autenitized at $880^{\circ}C$ followed by tempering at $350^{\circ}C{\sim}450^{\circ}C$ showed higher values than that of autenization at $930^{\circ}C$ due to fine grain size.

• 소성∙가공
• /
• 제22권2호
• /
• pp.101-107
• /
• 2013

The heat transfer characteristics between die and sheet and die and coolant are important parameters in hot press forming process. The determination of the quenching time that guarantees full martensitic transformation requires proper understanding of these heat transfer characteristics. The contact area changes drastically during the quenching process due to volume changes of both die and sheet by temperature drop as well as phase transformation. Several types of modeling techniques are tested in order to select the most suitable. The effect of quenching time as well as die heat conductivity on martensitic transformation is investigated and predictions are compared to experimental results.

• 대한전기학회논문지:전력기술부문A
• /
• 제53권2호
• /
• pp.73-79
• /
• 2004

Nowadays, one of the serious problems in KEPCO system is the larger fault current than the SCC(Short Circuit Capacity) of circuit breaker. There are many alternatives to reduce the increased fault current such as isolations of bus ties, enhancement of SCC of circuit breaker, applications of HVDC-BTB(Back to Back) and FCL(fault current limiter). However, these alternatives have some drawbacks in viewpoints of system stability and cost. As the superconductivity technology has been developed, the HTS-FCL(High Temperature Superconductor-Fault Current Limiter) can be one of the attractive alternatives to solve the fault current problem. Under this background, this paper presents the EMTDC model for resistive type HTS-FCL considering the nonlinear characteristic of final resistance value when quenching Phenomena occur.

• 열처리공학회지
• /
• 제18권2호
• /
• pp.112-118
• /
• 2005

Study was focused on the effect of the cooling rate on the embrittlement behavior of Zircaloy-4 cladding simulated Loss Of Coolant Accident (LOCA) environment. Claddings were oxidized at given temperature and given time followed by various water quenching in the range of $0.6^{\circ}C$ and $100^{\circ}C$ per second. Cladding failed after water quenching above the threshold oxidation. Threshold oxidation was decreased as the cooling rate increased, which is due to the matensite structure formed during fast cooling rate.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제53권2호
• /
• pp.73-73
• /
• 2004

Nowadays, one of the serious problems in KEPCO system is the larger fault current than the SCC(Short Circuit Capacity) of circuit breaker. There are many alternatives to reduce the increased fault current such as isolations of bus ties, enhancement of SCC of circuit breaker, applications of HVDC-BTB(Back to Back) and FCL(fault current limiter). However, these alternatives have some drawbacks in viewpoints of system stability and cost. As the superconductivity technology has been developed, the HTS-FCL(High Temperature Superconductor-Fault Current Limiter) can be one of the attractive alternatives to solve the fault current problem. Under this background, this paper presents the EMTDC model for resistive type HTS-FCL considering the nonlinear characteristic of final resistance value when quenching Phenomena occur.

• 한국재료학회지
• /
• 제19권6호
• /
• pp.293-299
• /
• 2009

The microstructures and mechanical properties of Dual Phase (DP), Transformation-Induced Plasticity (TRIP), and Quenching & Partitioning (Q&P) steels were investigated in order to define the strengthening mechanism of 0.2 C steel. An intercritical annealing between Ac1 and Ac3 was conducted to produce DP and TRIP steel, followed by quenching the DP and TRIP steel being quenched at to room temperature and by the TRIP steel being austemperingaustempered-air cooling cooled the steel toat room temperature, respectively. The Q&P steel was produced from full austenization, followed by quenching to the temperature between $M_s$ and $M_f$, and then enriching the carbon to stabilize the austenite throughout the heat treatment. For the DP and TRIP steels, as the intercritical annealing temperature increased, the tensile strength increased and the elongation decreased. The strength variation was due to the amount of hard phases, i.e., martensite and bainite, respectively in the DP and TRIP steels. It was also found that the elongation also decreased with the amount of soft ferrite in the DP and TRIP steels and with the amount of the that was retained in the austenite phasein the TRIP steel, respectively for the DP and TRIP steels. For the Q&P steel, as the partitioning time increased, the elongation and the tensile strength increased slightly. This was due to the stabilized austenite that was enriched with carbon, even when the amount of retained austenite decreased as the partitioning time increased from 30 seconds to 100 seconds.

• 소성∙가공
• /
• 제22권3호
• /
• pp.123-132
• /
• 2013

Hot stamping, which is the hot pressing of special steel sheet using a cold die, can combine ease of shaping with high strength mechanical properties due to the hardening effect of rapid quenching. In this paper, a thermo-mechanical analysis of hot stamping using the finite element method in conjunction with phase transformations was performed in order to investigate the plastic deformation behavior, temperature history, and mechanical properties of the stamped car part. We also conducted a fully coupled thermo-mechanical analysis during the stamping and rapid quenching process to obtain the mechanical properties with the consideration of the effects of plastic deformation and phase transformation on the temperature histories at each point in the part. The finite element analysis could provide key information concerning the temperature histories and the sheet mechanical properties when the phase transformation is properly considered. Such an analysis can also be used to determine the effect of cyclic cooling on the tooling.