• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권11호
• /
• pp.737-741
• /
• 2000

We fabricated resistive superconducting fault current limiters (SFCL) based on YBCO thin films grown on 2-inch diameter $Al_2O_3$ substrates. Two SFCLs with nearly identical properties were connected in series to investigate simultaneous quench. There was a slight difference in the rate of voltage increase between two SFCL units when they were operated independently. This difference resulted in significantly imbalanced power dissipation between the units. This imbalance was removed by connecting a shunt resister to an SFCL in parallel. The appropriate values of shunt resistance were 80 ${\Omega}$ at 75 $V_rms$ and 110 ${\Omega}$ at 120 $V_rms$, respectively. Increased power input at high voltages also reduced the initial imbalance in power dissipation, but with increase in film temperature to higher than 200 K.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 1999년도 제1회 학술대회논문집(KIASC 1st conference 99)
• /
• pp.109-112
• /
• 1999

The normal zone propagation (NZP) velocity and V-I characteristics of two Bi-2223 pancake coils with different Ag/SC ratio were investigated by experiment. Non-uniformity of Ic and broad restive transition was oberserbed in two coils. The NZP velocity of azimuth direction is faster than radius direction, and the NZP velocity of coil with higher Ag/SC ratio is faster than another coil with lower Ag/SC ratio.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 1999년도 High Temperature Superconductivity Vol.IX
• /
• pp.343-347
• /
• 1999

YBCO film을 이용한 meander 형태의 저항형 한류기에서 고장이 발생하였을 때 초기의 과도상태에서 볼수 있는 첨두전류를 억제하기 위하여 shunt 저항을 병렬로 취부한 경우의 전기적특성을 살펴보았다. 인가전압을 16.5 V$_{peak}$로 가하고 R$_0$는 1 ${\omega}$,R$_L$을 7.7 ${\omega}$으로 하고 shunt 저항을 5 ${\omega}$으로 하였을 때 약 12.2 A$_{peak}$의 전류값에서 최초quench가 발생하였으며 초전도 한류소자에 quench 발생으로 인한 저항이 발생함과 동시에 I$_1$으로 흐르던 사고전류의 일부가 shunt 저항이있는 I$_2$으로 서서히 분로하여 첨두전류가 거의 발생하지 않았다. 이때 초전도 한류기를 적용하지 않은 경우 최대 사고전류는 약 16.5 A$_{peak}$이었으며 초전도 한류기를 적용한 경우는 최대 한류전류값이 9 A$_{peak}$에서 4주기후에는 5.8 A$_{peak}$이었다. 인가전압 V$_0$=113 V$_{peak}$이고 표준저항 R$_0$는 1${\omega}$, 그리고 R$_L$을 7.7 ${\omega}$으로 하고 shunt 저항을 5 ${\omega}$으로 하였을 때 사고각 0 $^{\circ}$에서 사고전류값이 최고 23.0 A$_{peak}$까지 상승하고 이후 일정한 값을 유지하였다. 일반적으로 사고발생 직후에는 전류변화율에 의하여 전류값의 급격한 상승을 보이지만 shunt 저항이 전류분류의 역할을 수행하여 첨두전류는 거의 발생하지 않았다. 또한 상온의 gold층의 저항을 감안했을 때 사고발생후 약 36msec 후에 상온에 도달하였으며 shunt 저항이 없는 경우의 11 msec에 비하여 약 3배이상 길어졌다. 사고각 45 $^{\circ}$와 90 $^{\circ}$인 경우는 반복실험에 의한 시편의 특성저하(degradation)에 의하여 정상상태에서 초전도체에 흐르는 전류가 약간 발생하였다. 계통의 신뢰성이 중요한 요소로 작용하는 실제운전에서는 시편의 특성저하에 의한 quench전류의 감소를 감안하여 적절한 운전조건을 도출하여야 한다. 이상에서 앞으로는 장기간의 실제운전 조건을 고려하여 시편의 특성저하(degradation)와 가혹조건에 대한 전기적 특성에 대한 연구를 병행하고자 한다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 A
• /
• pp.41-43
• /
• 1996

This paper describes on concerning electromagnetical and thermal behaviors during normal transition in Bi-2223/Ag superconducting multifilamentary tapes by conduction cooling. Some experiments were carried with operating temperature, 10-40K, and transport current as parameters in zero magnetic field. Sample tapes are transited normally with heater to intiate a quench. The voltage and temperature properties which accord to normal transition are measured by voltage taps and thermocouples attached to sample tapes, we also calculated longitudinal and transverse directions normal-zone propagation velocities from the voltage traces.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.209-212
• /
• 1999

We studied the operating properties of resistive and inductive SFCLS with 100 $\Omega$ of quench impedance for a three-phase-fault in the 154 kV transmission system. The fault simulation at the phase angles 0$^{\circ}$ , 45$^{\circ}$ , and 90$^{\circ}$ showed that the resistive SFCL limited the fault current less than 16 kA without any DC component after one half cycle from the instant of the fault. On the other hand, the inductive SFCL suppressed the current below 11 kA, but with 3-4 kA of DC component which decreased to zero in 5 cycles. We concluded that the inductive SFCL had higher performance in current limiting but the resistive SFCL was better from the view point of DC components.

• 열처리공학회지
• /
• 제26권5호
• /
• pp.241-247
• /
• 2013

Hardenability and mechanical properties of boron-bearing steels containing C, Mo and Cr were investigated in this study. Using quench dilatometer, the steel specimens were cooled down to room temperature at different cooling rates to construct continuous cooling transformation diagrams and then the transformation products from austenite were examined. A critical cooling rate was introduced as an index to quantitatively evaluate the hardenability. The C addition to boron-bearing steels did not significantly affect hardenability compared to boron-free steels although it increases the hardenability. With the same content, the Mo addition largely increased the hardenability of boron-bearing steels than the Cr addition because it decreased both the transformation start and finish temperatures at low cooling rates. In particular, the Mo addition completely suppressed the formation of eutectoid ferrite even at the slow cooling rate of $0.2^{\circ}C/s$, whereas the Cr addition nearly suppressed it at the cooling rates above $3^{\circ}C/s$.

• 한국세라믹학회지
• /
• 제24권4호
• /
• pp.349-356
• /
• 1987

${\beta}$-Sialon powder was synthesized by the simultaneous reduction and nitridation of Hadong kaolin at 1350$^{\circ}C$ in N2-H2 atmosphere, using graphite as a reducing agent. The synthesized ${\beta}$-Sialon powder was pressurelessly sintered over 1450-1850$^{\circ}C$ in nitrogen atmosphere. The average particle size of ${\beta}$-Sialon powder was about 4.5$\mu\textrm{m}$. The relative density, M.O.R., fracture toughness and micro-hardness of ${\beta}$-Sialon ceramics sintered at 1800$^{\circ}C$ for 1 hour were 92%, 36 kpsi, 2.8MN/㎥/2 and 13.3 GN/㎡, respectively. The critical temperature difference (ΔT) in water quench thermal shock behavior showed about 375$^{\circ}C$ for the synthesized ${\beta}$-Sialon ceramics.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1355-1360
• /
• 2007

The use of high strength steels are gradually increasing to reduce the weight of automobile to improve the environmental problems and collision safety. To encounter the traditional disadvantages of high strength steels like as a poor formability and high springback, hot press forming has been developed. By this method, the strength of steel sheet is increased about three times of original one through die quenching process. In order to the design of hot press forming tools by using numerical simulation, the knowledge of mechanical and microstructural characteristics are required. This study show the mechanical and microstructural characteristics of a high strength boron-alloyed steel according to the various quenching conditions.

• 한국전기전자재료학회논문지
• /
• 제19권4호
• /
• pp.391-397
• /
• 2006

We present investigations of a hybrid type superconducting fault current limiter (SFCL), which consists of transformers and resistive superconducting elements. The secondary windings of the transformer were separated into several electrically isolated circuits and linked inductively with each other by mutual flux, each of which has a superconducting current limiting element of $YBa_2Cu_3O_7$ (YBCO) stripes as a current limiting element. Simple connection in series of the SFCL elements tends to produce ill-timed quenching because of power dissipation unbalance between SFCL elements. Both electrical isolation and mutual flux linkage of the elements provides a solution to power dissipation unbalance, inducing simultaneous quench and current redistribution of the YBCO films. This design enables to increase the voltage rating of SFCL with given YBCO stripes.

• 소성∙가공
• /
• 제23권8호
• /
• pp.475-481
• /
• 2014

Water quenching is one method of cooling after hot forming, which is presently being used for the manufacturing of automobile parts. The formed parts at room temperature are heated and then cooled rapidly in a water bath to produce high strength. The formed parts may undergo excessive thermal distortion during the water quench. In order to predict the distortion during water quenching, a coupled thermo-mechanical simulation is needed. In the current study, the simulation of heating and cooling of boron steel cylinders was performed. The material properties for the simulation were calculated from JMatPro, and the convective heat transfer coefficient was obtained from experimental tests. The results show that the thermal distortion and the residual stresses are well predicted by the coupled simulation.