• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.5
• /
• pp.548-553
• /
• 2015

The conventional ejector-diffuser system makes use of high pressure primary stream to propel the secondary stream through pure shear action for the purposes of transport or compression of fluid. It has been widely used in many industrial applications such as seawater desalination, solar refrigeration, marine engineering, etc. The present study is performed numerically to study the performance of a two-stage ejector-diffuser system. The detailed flow phenomenon of the ejector-diffuser system has been critically predicted by means of the numerical approach using compressible Reynolds averaged Navier-Stokes (RANS) equations. The axi-symmetric supersonic ejector-diffuser flow has been solved by a fully implicit finite volume scheme with a two-equation k-omega turbulence model. The numerical results are validated with existing experimental data. Detailed flow physics and their contributions on ejector performance are detected to compare both single-stage and two-stage ejectors. The performance improvement on the ejector-diffuser system is discussed in terms of the mass flux ratio and the coefficient of power.

• Membrane and Water Treatment
• /
• v.1 no.2
• /
• pp.159-169
• /
• 2010

The effect of external recycle on the performance of dialysis in countercurrent-flow rectangular membrane modules was investigated both theoretically and experimentally. Theoretical analysis of mass transfer in parallel-flow device with and without recycle is analogous to heat transfer in parallel-flow heat exchangers. Experiments were carried out with the use of a microporous membrane to dialyze urea aqueous solution by pure water. In contrast to a device with recycle, improvement in mass transfer is achievable if parallel-flow dialysis is operated in a device of same size with recycle which provides the increase of fluid velocity, resulting in reduction of mass-transfer resistance, especially for rather low feed volume rate.

• Solar Energy
• /
• v.18 no.1
• /
• pp.91-98
• /
• 1998

The study of mixed convection in a room with heated bottom surface and various partitions has been numerically investigated using a finite volume method. The parameters studied here are, 50$\overline{Nu}=\overline{Nu_n}{\cdot}(1+c(Re/Gr^{1/2})^d)$, where $\overline{Nu_n}$ corresponds to pure natural convextion.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.7 s.94
• /
• pp.1751-1760
• /
• 1993

The squeeze casting process is considered as an attractive way to form the primary product of near net shape metal matrix composites for wide use in automobile industry. To understand for infiltration limit in squeeze casting processes, the SAFFIL short fiber preform of volume fraction $10%{\sim}23%$ were fabricated by vaccum pumping and speed control press, and the optimal condition for fiber preform fabrication had been experimentally obtained. The composite materials were fabricated by forced infiltration of molten metals such as Al6061, Al7075, pure Al, AC8A, and Al2024. The infiltration distance and deformation of fiber preform are observed, and tensile strength were measured from at the room temperature.

• Microbiology and Biotechnology Letters
• /
• v.24 no.5
• /
• pp.540-545
• /
• 1996

A facultative anaerobe Enterococcus faecium 19-46-4 was used to study the production of an antimicrobial substance in anaerobic conditions. Major part of the antibiotic activity was found in the culture filtrate of the bacterium. The active compound was extracted by an equal volume of iso-butanol and concentrated in vacuo (at 50$\circ$C) before purification by C-18 liguid column chromatography and HPLC. A chromatographically pure compound was obtained by two passages of HPLC columns, The compound appeared as a pale-yellow powder. The yield was about 2.5 mg 1$^{-1}$ culture filtrate. The compound was named as KIST 194. KIST 194 were identified as cholic acid (3$\alpha$, 7$\alpha$, 12$\alpha$-trihydroxy-5$\beta$-cholan 24-oic acid) based on its physico-chemical properties determined by UV, IR, $^{1}H-NMR, $^{13}$C-NMR, El-MS and LC-MS.

• Journal of Korea Foundry Society
• /
• v.20 no.6
• /
• pp.407-418
• /
• 2000

The effect of various factors on the results of degassing of AC4C aluminum alloy melt by using rotary degasser were investigated. The difference between the effects of nitrogen gases of commercial pure and high purity grades on the degassing results was not significant. The optimum degassing condition was obtained. The effect of holding and degassing temperature was not significant, either. The result of degassing was deteriorated by the modification treatment of eutectic silicon, meanwhile improved by the grain refining. The effect of the latter was stronger than that of the former when the melt was treated simultaneously. The volume fractions of hydrogen porosity of the castings obtained from the molds with water moisture such as natural and green sand molds were much higher than those from the molds without that such as pep-set and $CO_2$ molds.

• Journal of Korean Society for Atmospheric Environment
• /
• v.16 no.6
• /
• pp.565-572
• /
• 2000

To quantitatively estimate mass contribution of long-range transported yellow sand, their sources should be separated independently from various local soil sources having similar elemental compositions. While it is difficult to estimate total mass loadings of pure yellow sand by traditional bulk analysis, it can be clearly solved by an particle-by-particle analysis. To perform this study, two yellow sand samples and three local soil samples were collected by a mini-volume sampler. These samples were three analyzed using a scanning electron microscope(SEM) equipped with an energy dispersive x-ray analyser (EDX) was used to obtain basic chemical information of individual yellow san particles. A total of 19 elements in a single particle were measured to develop a source profile with newly created homogeneous particle classes (HPCs) as chemical variables. The present study showed that the yellow sand samples as well as three local soil samples were characterized with reasonably well created HPCs. Finally the mass fraction of each HPC in each sample was calculated and then compared each other.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1061-1062
• /
• 2006

This paper presents a new approach for analyzing the microstructure of $SiC_p$-reinforced aluminum matrix composites from digital images. Various samples of aluminum matrix composite were fabricated by hot pressing the powder mixtures with certain volume and size combinations of pure Al and SiC particles. Microstructures of the samples were analyzed by computer-based image processing methods. Since the conventional methods are not suitable for separating phases of such complex microstructures, some new algorithms have been developed for the improved recognition and characterization of the particles in the metal matrix composites.

• Journal of Korea Foundry Society
• /
• v.14 no.1
• /
• pp.62-74
• /
• 1994

The concentration and particle size distribution of non-metallic inclusions which suspended in the molten aluminum at $700^{\circ}C$ were measured by using LiMCA apparatus. The result revealed that the number of inclusions increased with increasing the applied current or decreasing the orifice diameter, while decreased with increasing the purity of aluminum. And also, it was found that the number of inclusions increased with increasing the amount of boron added to molten aluminum. This was found to be attributed to the formation of the inclusions of TiB and $V_3B_2$. It was investigated that the average concentration of inclusions in a constant volume of 20ml of molten aluminum was increased in the order of pure molten aluminum, molten aluminum containing 20ppm of boron and molten aluminum used repeatly in the experimental casting in this study.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.05a
• /
• pp.112-113
• /
• 2019

Recently, supplementary cementitious materials such as blast-furnace slag, fly ash and silica fume have been widely used as substitutes for cementitious materials. In this study, the deformation behavior of compressive loading of C₃S paste with 50% fly ash was analyzed by X-ray scattering data and pair distribution function analysis. The obtained results were compared with 131-day-old pure C₃S paste. The Ca(OH)₂ of the C₃S-FA paste showed almost complete elastic behavior, consistent with the deformation behavior of the r-range of 20 to 40, and the C-S-H phase contributed to the range of PDF r-range of less than 20. In addition, C-S-H of C₃S-FA showed greater deformation resistance than C₃S paste.