• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.22 no.6
• /
• pp.383-391
• /
• 2010

In this study, HFC152a, HFC134a/HFC152a and HC290/HFC134a/HFC152a mixtures are studied for the supplementary and alternative refrigerants for HFC134a used in automobile air-conditioners. Due to the high global warming potential of HFC134a, it has to be phased out in the long run. Thermodynamic performance of these refrigerants are measured in a bench tester of 3.5 kW capacity with an open type compressor under both summer and winter conditions. Test results show that the coefficient of performance (COP) and capacity of pure HFC152a and HFC134a/HFC152a mixture are 9.1~12% and 7% higher than those of HFC134a. As for the HC290/HFC134a/HFC152a, the COP is up to 9.5% higher than that of HFC134a with 1~2% of HC290 while that is up to 6.1% lower than that of HFC134a with 5% HC290. The capacity of the ternary mixture, however, is 8.6% higher than that of HFC134a at all compositions tested. The compressor discharge temperatures of all refrigerants tested are $6{\sim}10^{\circ}C$ higher than that of HFC134a. For all refrigerants, the amount of charge is reduced up to 32% due to the decrease in liquid density. Overall, these refrigerants provide good performance with reasonable energy savings with less environmental problem and thus can be used as long term alternatives for automobile air-conditioners.

• Food Science and Preservation
• /
• v.21 no.3
• /
• pp.301-307
• /
• 2014

The purpose of this study was to examine the potential of turmeric (Curcuma longa L.) to inhibit 7,12-dimethylbenz[a]anthracene (DMBA)-induced mammary carcinogenesis in rats. Female Sprague Dawley rats were fed a control diet (NC and DC) or an ethanol extract of turmeric (DT) diet until the end of the experiment. The rats in the DC and DT groups were administered a single dose of DMBA (50 mg/Kg) by oral gavages at 50 days of age. The turmeric ethanol extracts decreased the incidence and multiplicity of DMBA-induced mammary tumor. The turmeric ethanol extract significantly decreased the tumor cell proliferation. The turmeric also significantly decreased the tumor grade based on the degree of the tubule formation. The results suggest that the ethanol extract of turmeric has an inhibitory effect against mammary carcinogenesis, and that such chemopreventive effect may be related to the inhibition of the initiation and the proliferation of tumor cells.

• Biomolecules & Therapeutics
• /
• v.8 no.1
• /
• pp.78-83
• /
• 2000

The objective of this study was to prevalidate the Organization for Economic Cooperation and Development's (OECD) rodent uterotrophic assay as a test method for screening of potential endocrine disrupting chemicals (EDCs). This study was conducted exactly as described in the OECD protocol documents. A positive control substance, 17$\alpha$-ethinyl estradiol (EE), was administered daily for three days to ovariectomized (OVX) Sprague-Dawley rats at various doses for determine the dose-response curve. Additionally, a pure antiestrogenic chemical, ZM189, 154 was administered to OVX rats at the same time EE to determine the effectiveness of the material against blocking the estrogenic effects of EE. At higher concentration of EE (10 $\mu\textrm{g}$/kg), a statistically significant difference in body weight gain and food consumption was observed compared to vehicle controls. In uterine responses, EE produced a dose-related increase in uterus weights compared to vehicle control. These increases were statistically significant at the >1.0 $\mu\textrm{g}$/kg doses. However, a similar dose-response relationship was not observed in vagina weight. A comparison of the two groups receiving ZM189,154 (0.1 and 1.0 mg/kg) with 0.3 $\mu\textrm{g}$/kg of EE and the group receiving only 0.3 $\mu\textrm{g}$/kg of EE showed dose-related decreases in uterus weights. However, statistical significance was shown in 1.0 mg/kg of ZM189,154. In conclusion, administration of EE produced a dose-related increase in uterine (wet and blotted) weights. Additionally, the 1.0mg/kg dose of ZM189,154 was effective in blocking the estrogenic activity of EE. These data suggest 3-day uterotrophic assay using OVX rats may serve as a good tool for EDCs screening.

• Advances in materials Research
• /
• v.1 no.4
• /
• pp.311-347
• /
• 2012

Infections are caused due to the infiltration of tissue or organ space by infectious bacterial agents, among which Staphylococcus aureus bacteria are clinically most relevant. While current treatment modalities are in general quite effective, several bacterial strains exhibit high resistance to them, leading to complications and additional surgeries, thereby increasing the patient morbidity rates. Titanium dioxide is a celebrated photoactive material and has been utilized extensively in antibacterial functions, making it a leading infection mitigating agent. In view of the property amelioration in materials via nanofication, free-standing titania nanofibers (pure and nominally doped) and nanocoatings (on Ti and Ti6Al4V implants) were fabricated and evaluated to assess their efficacy to mitigate the viability and growth of S. aureus upon brief (30 s) activation by a portable hand-held infrared laser. In order to gauge the effect of exposure and its correlation with the antibacterial activities, both isolated (only titania substrate) and simultaneous (substrate submerged in the bacterial suspension) activations were performed. The bactericidal efficacy of the IR-activated $TiO_2$ nanocoatings was also tested against E. coli biofilms. Toxicity study was conducted to assess any potential harm to the tissue cells in the presence of photoactivated materials. These investigations showed that the photoactivated titania nanofibers caused greater than 97% bacterial necrosis of S. aureus. In the case of titania-coated Ti-implant surrogates, the bactericidal efficacy exceeded 90% in the case of pre-activation and was 100% in the case of simultaneous-activation. In addition to their high bactericidal efficacy against S. aureus, the benignity of titania nanofibers and nanocoatings towards tissue cells during in-vivo exposure was also demonstrated, making them safe for use in implant devices.

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.9
• /
• pp.3753-3758
• /
• 2015

Background: Polymeric nanoparticles are attractive materials that have been widely used in medicine for drug delivery, with therapeutic applications. In our study, polymeric nanoparticles and the anticancer drug, chrysin, were encapsulated into poly (D, L-lactic-co-glycolic acid) poly (ethylene glycol) (PLGA-PEG) nanoparticles for local treatment. Materials and Methods: PLGA: PEG triblock copolymers were synthesized by ring-opening polymerization of D, L-lactide and glycolide as an initiator. The bulk properties of these copolymers were characterized using 1H nuclear magnetic resonance spectroscopy and Fourier transform infrared spectroscopy. In addition, the resulting particles were characterized by scanning electron microscopy. Results: The chrysin encapsulation efficiency achieved for polymeric nanoparticles was 70% control of release kinetics. The cytotoxicity of different concentration of pure chrysin and chrysin loaded in PLGA-PEG ($5-640{\mu}M$) on T47-D breast cancer cell line was analyzed by MTT-assay. Conclusions: There is potential for use of these nanoparticles for biomedical applications. Future work should include in vivo investigation of the targeting capability and effectiveness of these nanoparticles in the treatment of breast cancer.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.415-420
• /
• 2001

Water usage in the semiconductor industries is dramatically increased by not only using bigger wafer from 8 inches to 12 inches but also by adapting new process such as Chemical Mechanical Planarization (CMP) process invented by IBM in late '80. However, The document published by International Semiconductor Association suggests the decreasing ultra pure water (UPW) use from 22 gallon/in$^2$in 1997 to 5 gallon/in$^2$ in 2012. The criteria will possibly used as exporting obstacle in the future. Generally, Solid content of CMP slurry is about 15wt%. The slurry is diluted with UPW before fed to a CMP process. When the slurry is discharged from the process as waste, it contains 0.1~0.6wt% of solid content and 9~10 at pH. The CMP waste slurry is discharged to stream with minimum treatment. In this study, to find optimum condition of coagulation for water recovery from the waste CMP slurry various condition of coagulation were examined. After coagulation far 0.1 wt% solid content of waste CMP slurry, the sludge volume was 10~15% after 30 min of sedimentation time. For the 0.5 wt%, sludge volume was 50~55% after one hour of sedimentation time. For more than 80% of water recycling, the solid content should be in the range of 0.1 to 0.2wr%. Based on the result of the turbidity removal, the Zeta Potential and the analysis of heavy metals, the optimum condition for 0.1 wr% of waste CMP slurry was with 20 mg/L of PACI at 4 to 5 of pH. The result showed that the optimum conditions fer the 0.1 wt% waste CMP slurry were 100mg/L of Alum at 4~5 of pH, 100 mg/L of MgCI$_2$at pH 10 to 11 and 100 mg/L of Ca(OH)$_2$at pH 9 to 11, respectively.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.7
• /
• pp.2178-2182
• /
• 2011

Recently, the synthesis of ordered macroporous materials has received much attention due to its potential use as photonic band gap materials.$^1$ In this study, we have used the three-dimensional (3D) latex array template impregnated with benzenesulfonic acid (BSA), which is capable of catalyzing the reaction using tetraethyl orthosilicate (TEOS) as a precursor and distilled water. The polystyrene (PS) templates were reacted with TEOS in $scCO_2$ at 40 $^{\circ}C$ and at 80 bar. In the reactor, TEOS was filtrated into the PS particle lattice. After the reaction, porous silica materials were obtained by calcinations of the template. The stability test of the PS template in pure $CO_2$ was conducted before the main experiment. Scanning electron microscopy (SEM) images showed that the reaction in $scCO_2$ takes place only on the particle surface. This new method using $scCO_2$ has advantages over conventional sol-gel processes in its capability to control the fluid properties such as viscosity and interfacial tension. It has been found that the reaction in $scCO_2$ occurs only on the particle surface, making the proposed technique as more rapid and sustainable method of synthesizing inverse opal materials than conventional coating processes in the liquid phase and in the vapor phase.

• Archives of Pharmacal Research
• /
• v.29 no.3
• /
• pp.241-248
• /
• 2006

Angiotensin converting enzyme (ACE) inhibitors have cardioprotective effects in different species including human. This cardioprotective effect is mainly due to the inhibition of bradykinin (BK) degradation rather than inhibition of the conversion of angiotensin I to angiotensir. II. Bradykinin, a nonapeptide, has been considered to be the potential target for various enzymes including ACE, neutral endopeptidase 24.11, carboxypeptidase M, carboxypeptidase N, proline aminopeptidase, endopeptidase 24.15, and meprin. In the present study, the coronary vascular beds of Sprague Dawley rat isolated hearts were perfused (single passage) with Krebs solution alone or with different concentrations of BK i.e. $2.75{\times}10^{-10},\;10^{-7},\;10^{-6}\;and\;10^{-5}M$ solution. Percent degradation of BK was determined by radioimmunoassay. The degradation products of BK after passing through the isolated rat-hearts were determined using RP-HPLC and mass spectroscopy. All the four doses of BK significantly decreased the perfusion pressure during their passage through the hearts. The percentage degradation of all four doses was decreased as the concentration of drug was increased, implying saturation of a fixed number of active sites involved in BK degradation. Bradykinin during a single passage through the hearts degraded to give [1-7]-BK as the major metabolite, and [1-8]-BK as a minor metabolite, detected on HPLC. Mass spectroscopy not only confirmed the presence of these two metabolites but also detected traces of [1-5]-BK and arginine. These findings showed that primarily ACE is the major cardiac enzyme involved in the degradation of bradykinin during a single passage through the coronary vascular of bed the healthy rat heart, while carboxypeptidase M may have a minor role.

• Journal of the Korean Society for Heat Treatment
• /
• v.18 no.2
• /
• pp.91-98
• /
• 2005

Both commercially pure titanium and Ti-6Al-4V alloy have been widely used as biomaterials because of their excellent biocompatibility, corrosion resistance and mechanical properties. However, in recent years, vanadium has been found to cause cytotoxic effects and adverse tissue reactions, while aluminium has been associated with potential neurological disorders. A newly designed ${\alpha}+{\beta}$ type Ti alloy, Ti-10Ta-10Nb alloy showed superior properties to CP Ti and Ti-6Al-4V alloy in the point of biomaterial, and elucidated the future uses as a biomaterial. Microstructural changes of Ti-10Ta-10Nb alloy after hot-rolling, warm-rolling, solution and aging treatment were investigated. According to TEM results, the microstructures after solution treatment were composed of mostly ${\alpha}$ phase with a trace of ${\beta}$ phase due to adding ${\beta}$-phase stabilizer tantalum and niobium. The microstructures after warm-rolling is coarse and elongated ${\alpha}$ phase and hot rolling resulted in very fine ${\alpha}$ widmanst$\ddot{a}$tten. The highest value of hardness was obtained by aging treatment at $400^{\circ}C$ for 20hr in which microstructure consisted of very fine ${\alpha}$ phase in ${\beta}$ matrix.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.184-187
• /
• 2007

Hydrogen could be produced from any substance containing hydrogen atoms, such as water, hydrocarbon (HC) fuels, acids or bases. Hydrocarbon fuels couold be converted to hydrogen-rich gas through reforming process for hydrogen production. Even though fuel cell have high efficiency with pure hydrogen from gas tank, it is more beneficial to generate hydrogen from city gas (mainly methane) in residential application such as domestic or office environments. Thus hydrogen is generated by reforming process using hydrocarbon. Unfortunately, the reforming process for hydrogen production is accompanied with unavoidable impurities. Impurities such as CO, $CO_2$, $H_2S$, $NH_3$, and $CH_4$ in hydrogen could cause negative effects on fuel cell performance. Those effects are kinetic losses due to poisoning of electrode catalysts, ohmic losses due to proton conductivity reduction including membrane and catalyst ionomer layers, and mass transport losses due to degrading catalyst layer structure and hydrophobic property. Hydrogen produced from reformer eventually contains around 73% of $H_2$, 20% or less of $CO_2$, 5.8% of less of $N_2$, or 2% less of $CH_4$, and 10ppm or less of CO. Most impurities are removed using pressure swing adsorption (PSA) process to get high purity hydrogen. However, high purity hydrogen production requires high operation cost of reforming process. The effect of carbon dioxide on fuel cell performance was investigated in this experiment. The performance of PEM fuel cell was investigated using current vs. potential experiment, long run (10 hr) test, and electrochemical impedance measurement when the concentrations of carbon dioxide were 10%, 20% and 30%. Also, the concentration of impurity supplied to the fuel cell was verified by gas chromatography (GC).