• Transactions of Materials Processing
• /
• v.20 no.3
• /
• pp.206-213
• /
• 2011

A flexible die, which is composed of a number of punches with adjusted heights to form a three-dimensional curved surface, is a crucial part of a flexible forming technology. In this study, the punch and control system of the flexible die were designed. The flexible die is divided into three modules, namely, punch, control and joint, and the corresponding modules were developed. The punch module materializes a three-dimensional forming surface by the control module, which is composed of an AC servo motor set and a linear guide. The joint module is necessary for the sequential motion between the servo motor set and the punch module. A sequential motion algorithm for the AC servo motor set, that uses the data of the punch relative heights, was also proposed. Finally, a flexible stretch forming test was carried out using the presently designed flexible die.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.2
• /
• pp.440-449
• /
• 1996

Superplastic punch forming of sheets is simulated by a finite element method to obtain the optimal punch speed and the related deformed shapes. The punch forming has an advantage of guaranteeing the desired accuracy inside a product and controlling the thichness of a deformed sheet more accurately than blow forming. The finit element code developed is associated with the contact algorithm and the control algorithm of punch speed for the optimum forming. The simulation demonstrates that the variation of the thichness in a blank sheet affects the punch speed and the final distribution of the thichness in a product. The analysis proposes that a ring-typed thichness controller is very effective in controlling the thichness of a deformed sheet appropriately.

• Transactions of Materials Processing
• /
• v.13 no.2
• /
• pp.129-136
• /
• 2004

Recently, instead of a matched die forming method requiring a high cost and long delivery term, a multi-point dieless forming method using a pair of matrix type punch array as flexible dies has been developed. Since the conventional multi-point dieless forming method has some disadvantages of difficulty in precise punch control and high-cost of equipment, a new concept of multi-point dieless forming method combined with an elasto-forming method has been suggested in this study. For optimal selection of elastomers, compression tests of rubbers, polyethylene and foams were carried out together with FEM analysis of the deformation behavior during sheet forming process using a rigid punch and elastomers. Compressive strain was concentrated on the upper central area of the elastomer under the punch, and the rubber exhibited higher concentration of the compressive strain than foams. Two-dimensional curved surface was formed successfully by the multi-point elasto-dieless forming method using an optimal combination of rubber and foam materials.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.08a
• /
• pp.21-28
• /
• 2003

Recently, instead of a matched die forming method requiring a high cost and long deliverly ten a multi-point dieless forming method using a pair of matrix type punch array as flexible dies has been developed. As this multi-point dieless forming method has some disadvantage of difficulty in precise punch control and high-cost of equipment, a new concept of multi-point dieless forming method combined with elastomer forming was suggested in this study. For optimal selection of elastomers, compression tests of rubbers, polyethylene and foams were carried out together with FEM analysis of the deformation behavior during sheet forming process using a rigid punch and elastomers. Compressive strain was concentrated on the upper central area of the elastomer under the punch, and the rubber exhibited higher concentration of the compressive strain than foams. Two-dimensional curved surface was formed successfully by the multi-point elasto-dieless forming method using an optimal combination of a rubber and foam.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.18-21
• /
• 1999

In this study in order to make doubly-curved sheet metal effectively a sheet metal forming process has been developed by adopting the flexibility of the incremental forming process and the principle of bending deformation which causes slight deformation to thickness The developed process is an unconstrained forming process with no holder. For this study the experimental equipment is set up with the punch-set which consists of two pairs of lower support-punches and one upper center-punch. In the experiments using aluminum sheet it is found that the curvature of the formed sheet metal is determined by controlling the distance between supporting punches in pairs and the forming depth of the center-punch. and the edge-forming method is proposed for forming the sheet metal into the balanced shape. The equation using process variables such as the distance between supporting punches in pairs and the forming depth of the center-punch is proposed for the prediction of the radii of curvatures of the formed shape and it is corrected by the experimental results and the FEM simulation results about whether springback takes place. It is found that according o the simulation there is a certain set of the distance between a pair of supporting punches and the forming depth of the center-punch which causes a little springback. It is thus shown that the radii of curvatures of the formed sheet metal can be predicated by the corrected equation unless significant springback occurs.

• Design & Manufacturing
• /
• v.10 no.2
• /
• pp.44-49
• /
• 2016

The roll forming produces mass products using the continuous production process. Also we need the process that continuous long material or goods cutting into a desired length. Our study uses 3-D driving cutter and roll forming material as SPCC to investigate this. When we cut the material using the process of roll forming, the shear resistance is raised at the cutting punch's edge. The result is remained the trouble about burr and progressive deformation on the material. This study shows the method minimizing the above trouble. The material of punch was considering heat generated on the continuous production process. So we used the type of STD 61 for the material of punch and had the vacuum heat treatment for the surface hardness of HRC 53. The structure of the mold is designed with forming a double cam die at the upper punch and the both sides of central core. We conducted the experiment three times. In the result when had to make V-groove within the angle between 105 and 110 on the punch front end, we could get the minimum shear resistance on the punch front end. Also with the same condition we minimizes the material jams in the continuous production process.

• Transactions of Materials Processing
• /
• v.19 no.8
• /
• pp.486-493
• /
• 2010

A shape error of the sheet metal product made by a flexible stretch forming process is occurred by a various forming parameters. A die used in the flexible stretch forming is composed of a punch array to obtain the various objective surfaces using only one die. But gaps between the punches induce the shape error and the defect such as a scratch. Forming parameters of the punch size and the elastic pad to prevent the surface defect must be considered in the flexible die design process. In this study, tendency analysis of shape error according to the forming parameters in the flexible stretch process is conducted using a finite element method. Three forming parameters, which are the punch size, the objective curvature radius and the elastic pad thickness, are considered. Finite element modeling using the punch height calculation algorithm and the evaluation method of the shape error, which is a representative value for the formability of formed surface, are proposed. Consequently, the shape error is in proportion to the punch size and is out of proportion to the objective curvature radius and the elastic pad thickness.

• Transactions of Materials Processing
• /
• v.14 no.9 s.81
• /
• pp.772-778
• /
• 2005

This paper is concerned with the analysis of material flow characteristics of combined tube extrusion using pipe. The analysis in this paper concentrated on the evaluation of the design parameters for deformation patterns of tube forming, load characteristics, extruded length, and die pressure. The design factors such as punch nose radius, die corner radius, friction factor, and punch face angle are involved in the simulation. The combined tube extrusion is analyzed by using a commercial finite element code. This simulation makes use of pipe material and punch geometry on the basis of punch geometry recommended by International Cold Forging Group. Deformation patterns and its characteristics in combined forward and backward tube extrusion process were analyzed for forming loads with primary parameters, which are various punch nose radius relative to backward tube thickness. The results from the simulation show the flow modes of pipe workpiece and the die pressure at the contact surface between pipe workpiece and punch. The specific backward tube thickness and punch nose radius have an effect on extruded length in combined extrusion. The combined one step forward and backward extrusion is compared with the two step extrusion fer forming load and die pressure.

• Transactions of Materials Processing
• /
• v.10 no.3
• /
• pp.235-245
• /
• 2001

Deep drawing process, one of sheet metal forming methods, is very useful in the industrial field because of its efficiency The deep drawing is affected by many process variables, such as blank shapes, shape radii of the punch and die, formability of materials and so on. Especially, blank shape is very important formability factor. In this study, in order to investigate the effects of blank shape, we suggested three kinds of blank shapes and examined friction test about three conditions. We measured punch load distribution according to punch stroke under the conditions of each punch and die shape radii and observed punch load of elliptical cup forming.

• Journal of Institute of Convergence Technology
• /
• v.3 no.2
• /
• pp.31-37
• /
• 2013

This paper proposes a vision-based inspection algorithm for a punch which is used when forming the head of the small screws. To maintain good quality of punch, the precise inspection of its dimension and the depth of the punch head is important. A CCD camera and an illumination dome light are used to measure its dimensions. And a structured line laser is also used to measure the depth of the punch head. Resolution and visible area depend on setup between laser and camera which is determined using CAD-based simulation. The proposed method is successfully evaluated using experiment on #2 punch.