• The Korean Journal of Pain
• /
• v.12 no.1
• /
• pp.21-26
• /
• 1999

Background: Preoperative blocking of surgical nociceptive inputs may prevent sensitization of central nervous system (CNS) and reduce postoperative pain. The stress responses to surgical trauma consist of increase in catabolic hormones and decrease in anabolic hormones. We studied whether preoperative low dose epidural bupivacaine and morphine could affect postoperative pain, changes plasma cortisol, and serum glucose. Methods: Thirty patients undergoing total abdominal hysterectomy were randomly assigned to one of three groups. General anesthesia was induced in all patients and after that, epidural blocks were done except the control group (n=10) patients. Preoperative block group (n=10) received 0.5% bupivacaine 50 mg and morphine 2 mg epidurally as a bolus before operation and followed by 0.1% bupivacaine $5\;mghr^{-1}$ and morphine $0.2\;mghr^{-1}$ for 10 hours. Postoperative block group (n=10) received the same doses of bupivacaine and morphine under the same method postoperatively. Postoperative pain relief was provided with i.v. fentanyl through Patient-Controlled-Analgesia Pump. Postoperative pain by visual analogue scores (VAS), analgesic requirement (first requirement time, total amounts used), side effects, plasma cortisol level and serum glucose level were compared. Results: Until postoperative 6 hrs, VAS of control group was higher than those of the epidural groups. No difference was observed in VAS between the two epidural groups. First analgesics requirement time and total amounts of used analgesics were not different between the two epidural groups, but first analgesic requirement time of preoperative block group was significantly prolonged compared with control group. Plasma cortisol and serum glucose levels were not different among groups. Conclusions: Low dose preoperative epidural bupivacaine and morphine could not reduce postoperative pain, plasma cortisol level and serum glucose level compared with postoperative block group.

• Fire Science and Engineering
• /
• v.32 no.5
• /
• pp.57-66
• /
• 2018

A sports center fire in Jecheon that caused 29 deaths and 40 injuries was analyzed based on initial response and management in order to investigate the causes of the casualties. The aspects of initial response included delay of reporting 119, not being guided to the exit for the body scrubber on the $2^{nd}$ floor for escape, opening the fire doors of the exits on the $1^{st}$ floor and $3^{rd}$ floor, not closing the fire door of the main stairs on the $3^{rd}$ floor, and not doing an emergency broadcast. The management aspects included closing the alarm valve of the sprinkler system on the $1^{st}$ floor, starting-stop of the fire pump controller, neglecting leakage of water and electricity between the false ceiling and ceiling in the parking lot, hiding the exit light in the ladies bathroom lounge on the $2^{nd}$ floor and piling up things in the exit, neglecting the button of an automatic door on the $2^{nd}$ floor, conventional fire safety management, insufficient inspection of fire equipment, and not working fire shutters and smoke exhaust windows.

• Nuclear Engineering and Technology
• /
• v.46 no.5
• /
• pp.633-640
• /
• 2014

In this research, the surface roughness affecting the pressure drop in a pipe used as the steam generator of a PWR was studied. Based on the CFD (Computational Fluid Dynamics) technique using a commercial code named ANSYS-FLUENT, a straight pipe was modeled to obtain the Darcy frictional coefficient, changed with a range of various surface roughness ratios as well as Reynolds numbers. The result is validated by the comparison with a Moody chart to set the appropriate size of grids at the wall for the correct consideration of surface roughness. The pressure drop in a full-scale U-shaped pipe is measured with the same code, correlated with the surface roughness ratio. In the next stage, we studied a reduced scale model of a U-shaped heat pipe with experiment and analysis of the investigation into fluid-structure interaction (FSI). The material of the pipe was cut from the real heat pipe of a material named Inconel 690 alloy, now used in steam generators. The accelerations at the fixed stations on the outer surface of the pipe model are measured in the series of time history, and Fourier transformed to the frequency domain. The natural frequency of three leading modes were traced from the FFT data, and compared with the result of a numerical analysis for unsteady, incompressible flow. The corresponding mode shapes and maximum displacement are obtained numerically from the FSI simulation with the coupling of the commercial codes, ANSYS-FLUENT and TRANSIENT_STRUCTURAL. The primary frequencies for the model system consist of three parts: structural vibration, BPF(blade pass frequency) of pump, and fluid-structure interaction.

• Nuclear Engineering and Technology
• /
• v.48 no.5
• /
• pp.1083-1095
• /
• 2016

The design of Prototype Gen-IV Sodium-Cooled Fast Reactor (PGSFR) has been developed and the validation and verification (V&V) activities to demonstrate the system performance and safety are in progress. In this paper, the current status of test activities is described briefly and significant results are discussed. The large-scale sodium thermal-hydraulic test program, Sodium Test Loop for Safety Simulation and Assessment-1 (STELLA-1), produced satisfactory results, which were used for the computer codes V&V, and the performance test results of the model pump in sodiumshowed good agreement with those in water. The second phase of the STELLA program with the integral effect tests facility, STELLA-2, is in the detailed design stage of the design process. The sodium thermal-hydraulic experiment loop for finned-tube sodium-to-air heat exchanger performance test, the intermediate heat exchanger test facility, and the test facility for the reactor flow distribution are underway. Flow characteristics test in subchannels of a wire-wrapped rod bundle has been carried out for safety analysis in the core and the dynamic characteristic test of upper internal structure has been performed for the seismic analysis model for the PGSFR. The performance tests for control rod assemblies (CRAs) have been conducted for control rod drive mechanism driving parts and drop tests of the CRA under scram condition were performed. Finally, three types of inspection sensors under development for the safe operation of the PGSFR were explained with significant results.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.12
• /
• pp.842-849
• /
• 2007

For a $CO_2$ two-stage twin rotary compressor used for heat pump water heater system, changes of $CO_2$ solubility in PAG oil were investigated along the gas passages from the first stage suction to final discharge. Only slight changes in solubility took place in suction chambers for both of the first and second stages, but for compression chambers, solubility variation ranged from 0.115 to 0.136, and from 0.133 to 0.182, respectively for the first and second stages. Calculation of gas flashing in parts of leakage oil flows and of oil contained in control volumes due to solubility changes was conducted and included in gas pressure calculation. For the second stage, gas flashing amounts to around $5%\sim6%$ for most leakage flows. Cooling capacity, compressor input, and COP obtained by calculation were well compared to the experimental results. Effects of operation speed on the compressor performance was also studied: as the shaft speed increased, adiabatic efficiency decreased rapidly due to increased over-compression loss.

• Korean Journal of Optics and Photonics
• /
• v.17 no.3
• /
• pp.223-230
• /
• 2006

We demonstrate a distributed fiber sensor system based on spatially-selective Brillouin scattering, using a single laser diode as a light source whose optical frequency is directly modulated by the injection current. The pump and the counter-propagating probe lights, which are sinusoidally frequency-modulated, are superposed in the fiber so that stimulated Brillouin scattering takes places only at a specific location along the fiber. Brillouin gain peak position is controlled by varying the modulation frequency. Distributions of Brillouin shift frequency are measured for the case of concatenated optical fibers of two different kinds and also for the case of temperature distribution. The temperature coefficient of the Brillouin shift frequency is measured to be $1.33MHz/^{\circ}C$.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.4
• /
• pp.25-32
• /
• 2001

A microwave vacuum (MW/V) dryer was developed for drying short roundwoods, from which woodcraft souvenirs in Korean market are mostly made, and which were hardly dried without defects in a conventional kiln. It consisted of three 1.5 kW magnetrons of 2,450 MHz, a vacuum pump, a load cell of 100 kg and a cavity of $580{\times}580{\times}1,360\;mm^3$. A computer program was developed to switch on or off the magnetrons according to drying schedules, those were based on microwave injection time or the average of wood temperatures. To evaluate the new MW/V dryer the roundwood specimens of rigida pine, poplar and birch were dried. Their log diameters and lengths ranged from 125 to 25 em and from 25 to 50 cm, respectively. In spite of the presence of minor drying defects, the MW/V drying is found to be an effective method for drying short roundwoods. Wooden turneries made of red alder and ash logs were also MW/V dried from green to 4%MC without any degradation. The rates of the MW/V drying were examined for three different lengths of poplar logs.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.9 no.4
• /
• pp.504-516
• /
• 1997

Recently scientists and engineers are developing a system to get waste heat of low-temperature level with advanced heat pump, which have not been used up to now. As the reason, it is necessary to examine capability of using waste heat which is raised up in the tunnel of subway out of widely distributed low-temperature waste heat in large cities. Therefore we surveyed thermal environment of the tunnel of subway in $S\check{o}my\check{o}n$, downtown of Pusan, from November 1995 to December 1996 and developed a program to predict the thermal environment of subway on the basis of experimental data and the geometries of tunnels. This paper has proved availability of waste heat of subway when the measured results obtained in subway in the winter time and the simulated results of thermal environment prediction program are compared, as well as has reported results of estimating reliability of the simulation program. As the result, the charateristics of thermal environment in the tunnel of subway in $S\check{o}my\check{o}n$ station in the winter time are to be followed; 1) temperature in the tunnel is about $10^{\circ}C$ higher than outside air temperature, 2) temperature change in the tunnel is less than that in the platform so that we may obtain stable heat source, 3) and when the measured results obtained in subway in the winter time and the simulated results of thermal environment prodiction program is compared, both results show similar tendency. Therefore, we confirm estimating reliability of the simulation program.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.1475-1486
• /
• 2008

Bentonite-based grouting has been popularly used to seal a borehole installed for a closed-loop vertical ground heat exchanger in a geothermal heat pump system (GHP) because its high swelling potential. However, if the bentonite-based grouting is conducted in coastal areas, the salinity of groundwater changes in the mineral fabric of bentontie. In order words, an increase of cation concentration in groundwater leads to a reduction in the diffuse double-layer thickness in the bentonite mineral structure, and thus the volume of bentointe-based grouts will decrease proportional to the salinity of groundwater. In this paper, the effect of salinity (i.e., NaCl 0.5M, 0.25M, and 0.1M) on the change of swelling potential for bentonite-based grouts has been quantitatively evaluated for seven bentonite grouts from different product sources. In addition, in case of using addictives such as a silica sand to increase the thermal conductivity of bentonite-based grouts, the possibility of particle segregation has been studied considering the viscosity of grouts and salinity of groundwater.

• Journal of the Korean Institute of Gas
• /
• v.16 no.2
• /
• pp.38-44
• /
• 2012

In recent years, the need for more fuel-efficient and lower-emission vehicles has driven the technical development of alternative fuels such as LPi (Liquid phase LPG injection) which uses pump for the high pressure supply of liquid LPG fuel and is able to meet the limits of better emission levels while it has an advantage of higher power. Although it has the advantage of power and lower emission levels, the characteristics of LPG, such as high vapor pressure, lower viscosity and surface tension than gasoline fuels makes it difficult design system. Therefore most fuel pumps and injectors are imported. In the present study, in order to domestically develop LPG injector which guarantees flow rates and optimal operation, the experimental investigation on leakage and flow rate characteristics of developed prototype injector was carried out at the bench test rig for developed injector.