• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 학술대회 논문집 전문대학교육위원
• /
• pp.166-171
• /
• 2002

We are in transitional period of welding technique, which has changed from the stage of quantity and quality to the stage of future technique, imported and introduced from many advanced countries. Therefore, many researches and studies for development on high speeding and making welding machines with high effectiveness has been doing vigorously. In this dissertation, I have studied on a pulsed MAG welding machine, with which welding of thin plates may perform high speeding and effecting. First, I produced a phase shifted full bridge DC-DC convert, which is the type of reduced conduction loss and the power supply for welding machine. And then, I found out an output waveform control algorithm about one pulsed one droplet and short waveform control for thin plates with high speed by deriving the circuit model utilizing the circuit averaged method for full bridge converter.

• 한국표면공학회지
• /
• 제43권3호
• /
• pp.154-158
• /
• 2010

Numerical analysis is done to investigate the effects of pulse bias on the plasma processing characteristics like ion doping and ion nitriding by using fluid dynamic code with a 2D axi-symmetric model. For 10 mTorr of Ar plasma, -1 kV of pulse bias was simulated. Maximum sheath thickness was around 20 mm based on the electric potential profile. The peak electron temperature was about 20 eV, but did not affect the averaged plasma characteristics of the whole chamber. Maximum ion current density incident on the substrate was 200 $A/m^2$ at the center, but was decreased down to 1/10th at radius 100 mm, giving poor radial uniformity.

• 한국표면공학회지
• /
• 제53권6호
• /
• pp.343-350
• /
• 2020

The degradation of mechanical properties of nitride coatings to steel substrates is one of the main challenges for industrial applications. In this study, plasma nitriding treatment was used in order to increase the mechanical properties of Mo-Cu-N coating to the H13 tool steel. The nanostructured Mo-Cu-N coating was deposited using pulsed DC magnetron sputtering method with a single alloy Mo-Cu target. Mechanical properties of MoN-Cu coated samples after nitriding were found to be relatively better than non-nitrided MoN-Cu coating.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.1234-1235
• /
• 2011

A DC Power Distribution Systems(DC PDS) are widely used in telecommunication system, electric vehicle, aircraft, military system, etc. In the DC PDS, DC bus voltage instability may be occurred by the operation of multiple loads such as pulsed power load, motor drive system, and constant power loads. To damp the transients of the DC bus voltage, the Voltage Bus Conditioner(VBC) with the PI compensator is used. In this paper, the validity of the proposed VBC system is verified by PSIM simulation package.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2002년도 전력전자학술대회 논문집
• /
• pp.378-381
• /
• 2002

This paper describes a novel multilevel ad/dc power converter suitable for the protection of frequent output short-circuit. The output dc power of the proposed converter can be disconnected from the load within several hundred microseconds at the instant of short-circuit fault. The rising time of the dc load voltage is as small as several hundred microseconds, and there is no overshoot of the do voltage because the dc output capacitors keep undischarged state. Analysis and simulations are carried out to investigate the operation and usefulness of the proposed scheme.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 E
• /
• pp.2179-2181
• /
• 1999

This paper describes the composition technology of pulsed power system with high current. The capacitor bank, control cabinet, dc charging unit, closing switch and cable system etc. employed with the system components are described. Especially the development of the inverse pinch switch enabled the generation of the very high current.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제37회 하계학술대회 초록집
• /
• pp.406-406
• /
• 2009

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2014년도 추계학술대회 논문집
• /
• pp.274-274
• /
• 2014

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2005년도 제29회 학술발표회 초록집
• /
• pp.154-154
• /
• 2005

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.250-250
• /
• 2011

Pulsed DC magnetron sputter 진공 웹코팅 연속증착기를 사용하여 PET 또는 PEN 기판 위에 Al2O3 가스 배리어 박막을 형성 하였다. 주사전자현미경 측정으로 표면을 분석하였고, PERMATRAN-W3/33을 사용하여 투습률 값을 결정하였다. PEN과 PET 기판위의 가스 배리어 막 모두 O2 분압이 증가 할수록 투습률이 증가하였다. O2 분압이 증가함에 따라 결정립들 사이에 크랙이 발생하여 투습률값에 영향을 미치는 것을 확인하였다. PET 보다 PEN 기판위에 증착막이 더 O2분압이 증가할수록 크랙이 증가하였다. PET 위에 SiO2, SiOC 및 SiON 박막을 증착하여 SiO2는 두께에 따른 변화를 SiOC와 SiON는 부분압의 변화에 따른 투습률값과 투과도값을 측정하였다. SiO2 박막 두께가 500 nm일 때 최소의 투습률인 6.63 g/m2/day를 얻었고, SiO2 박막 두께가 $1{\mu}m$ 일 때 투습률값이 9.46 g/m2/day로 증가하였다. 투과도값은 두께가 증가할수록 감소하는 것을 보였다. 이러한 결과는 투습률값이 두께 변화에 따른 영향보다 표면의 결정립들의 영향에 더 민감함을 알 수 있었다. 부분압이 $6.6{\times}10^{-4}Torr$일 때 SiOC와 SiON의 최소의 투습률이 각각 7.85 g/m2/day 이고 8.1 g/m2/day 이며 SiOC 박막의 투습률 보다 작았다.