• Journal of Mechanical Science and Technology
• /
• 제17권10호
• /
• pp.1475-1484
• /
• 2003

The EDM processing characteristics of one of the nickel-based heat resistant alloys, Hastelloy- X, were investigated under the various EDM conditions and analyzed in terms of surface integrity. This alloy is commonly used as a material for the hot gas path component of gas turbines and it is difficult to machine by conventional machining methods. The primary EDM parameter which was varied in this study were the pulse-on time. Since the pulse-on time is one of the main factors that determines the intensity of the electrical discharge energy, it was expected that the machining ratio and the surface integrity of the specimens would be proportionally dependent on the pulse-on duration. However, experimental results showed that MRR (material removal rate) and EWR (electrode wear rate) behaved nonlinearly with respect to the pulse duration, whereas the morphological and metallurgical features showed rather a constant trend of change by the pulse duration. In addition the heat treating process affected the recast layer and HAZ to be recrystallized but softening occurred in recast layer only. A metallurgical evaluation of the microstructure for the altered material zone was also conducted.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제2C권6호
• /
• pp.304-308
• /
• 2002

We demonstrate a simple pulsed $CO_2$ laser with millisecond long pulse duration in a tube at a low pressure of less than 30 Torr. The novel power supply for our laser system switches the voltage of the AC power line (60Hz) directly. The power supply doesn't need elements such as a rectifier bridge, energy-storage capacitors, or a current-limiting resistor in the discharge circuit. To control the laser output power, the pulse repetition rate is adjusted up to 60Hz and the firing angle of SCR(Silicon Controlled Rectifier) gate is varied from 30。 to 150。. A ZCS (Zero Crossing Switch) circuit and a PIC one-chip microprocessor are used to control precisely the gate signal of the SCR. The maximum laser output of 35 W is obtained at a total pressure of 18 Torr, a pulse repetition rate of 60 Hz, and a SCR gate firing angle of 90。 . In addition, the resulting laser pulse width is approximately 3㎳(FWHM). This is a relatively long pulse width, compared with other repetitively pulsed $CO_2$ lasers.

• 한국통신학회논문지
• /
• 제19권1호
• /
• pp.1-9
• /
• 1994

In general, when IIR digital filter are designed from analog filters, the bilinera transformation and the impluse invariant tramsformation are commonly used. It is known, however, that high frequency response of digital filters designed by these transformations can not be well approximated to the sampled analog signals. In this paper, the symbol pulse invariant transformation is analyzed theoretically so that the symbol pulse invariant transformation which was originally application to a rectangular pulse is newly applied to double rate pulse signals and generic shape pulse signals. Also, the relation of spectra between a transfer function of digital filter and one of analog filter is considered. Further, we apply to design the digital high pass filters using the symbol pulse invariant transformation method.

• Journal of Communications and Networks
• /
• 제5권4호
• /
• pp.365-373
• /
• 2003

This paper investigates the performance of M-ary pulse position modulation (PPM) multiuser ultra-wideband (UWB) communication systems in terms of symbol error rate (SER) over fading and additive white Gaussian noise (AWGN) channel. Based on Gaussian approximation for the multiple access interference, an expression for the signal-to-noise ratio (SNR) is derived for the UWB system. This expression is used to derive exact SER expressions for coherent UWB receivers. The effect of pulse selection on the SER of multiuser UWB system is studied. In addition to rectangular pulse, the 2nd derivative Gaussian waveform and Rayleigh pulses were considered. We show that the system capacity and/or SER performance can be significantly increased by using the monocycle pulse in fading channels.

• 대한기계학회논문집
• /
• 제12권2호
• /
• pp.389-396
• /
• 1988

본 연구에서는 위의 세가지 보간 알고리즘 가운데서 가장 속도의 균일성이 좋은 DDA방식을 채택하였다. 그리고 윤곽제어에서 가공경로는 대개 직선과 원호 구간의 조합으로 구성되어질 수 있기 때문에, 본 연구에서는 직선 및 원호보간만 고려하기로 한다.

• 한국전자파학회논문지
• /
• 제14권2호
• /
• pp.139-147
• /
• 2003

본 논문에서는 FCC에서 제정한 허용 주파수 대역 내에서 100 Mbps급 M-ary PPM/TH UWB 시스템 설계를 위한 특성 파라미터의 규격을 제안하고, AWGN 채널에서 제안된 시스템의 성능을 분석하였다. 성능 분석 결과, 이 시스템에 적용 가능한 펄스 주기는 매우 한정적이며, 시스템의 데이터 전송률을 일정하게 할 경우, M과 펄스반복 개수가 증가할수록 시스템 성능은 개선되고, 사용자 수는 감소됨을 관측하였다.

• 전기학회논문지
• /
• 제63권7호
• /
• pp.962-967
• /
• 2014

In this paper, through a digital potentiometer and exponentially weighted moving average filter, pulse and PPG waveform measurable device was fabricated in radial artery. If this device is not proper about signal size in analog part, MCU can judge easily by adjusted amplification through digital potentiometer, using exponentially weighted moving average filter is able to filter out more clear value of ADC. I presumed pulse rate as value of measuring time between point of maximum contraction from sensing signal in radial artery of wrist. Therefore, this means can measure stable pulse rate and PPG waveform, finger as well as radial artery, whether signal size of each person is different finger as well as radial artery.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.827-831
• /
• 1997

Conductive veramic matrix composite(CMC) workpiece of TiC 33%/Al /sab 2/O /sab 3/ 66% Y /sab 2/ O /sab 3/ was machined by die sinking electrical discharge machining(EDM) according to different pulse duration and suty factor for reverse polarity of electrode. Material removal rate(MRR) was examined by process under various operating conditions. The surface morphology was evaluated by surface roughness values and scanning electron microscopy(SEM) research. The more MRR was obtained according to increase pulse duration and duty factor. Also the maximum surface roughness(Rmax) of EDMed surface was slightly changed with increased pulse duration and duty factor. The SEM photographs of EDMed surface showed wide recast wide recast distribution region of melting materials in purse duration 0.130(ms) than 0.048(ms).

• Journal of Welding and Joining
• /
• 제15권6호
• /
• pp.85-95
• /
• 1997

This study is to investigate the optimum conditions of Nd:YAG laser beam welding for Zircaloy-4 end cap closure by optical fiber transmission. Laser welding parameters which affect the penetration depth and bead width were experimentally examined using the various beam radius by the beam quality analyzer, joint geometries of end cap and the laser parameters which mean pulse width, repetition rate and pulse energy. Also, an optimum welding speed and the effect of assistant gas with varying the flow rate of He were investigated. We found that the laser average power for the end cap welding will be 230W and rotation speed must not exceed 8 RPM, the best position of focus using optical fiber with 600.mu.m will be 2 to 3mm below the surface of the material.

• 한국통신학회논문지
• /
• 제31권6C호
• /
• pp.569-574
• /
• 2006

PPM(Pulse Position Modulation)을 기반으로 하는 초광대역(ultra-wide bandwidth) 무선전송 시스템의 일반적인 전력 밀도 함수(power spectral density function)를 유도한다. 또한 개선된 선 스펙트럼(line spectrum) 특성과 우수한 BER(Bit Error Rate) 성능을 갖는 초광대역 무선전송 시스템을 제안한다.