• The Journal of Korean Physical Therapy
• /
• 제32권1호
• /
• pp.52-57
• /
• 2020

Purpose: This study compared the muscle activities of the Vastus medialis oblique (VMO) and the Vastus lateralis (VL) at three different knee extension angles: 90°, 135°, and 180° in the sitting position. Methods: Twenty subjects between 20 and 30 years of age participated in the study. A mobile phone application called the Clinometer was used to measure the knee joint angle. Electromyography (EMG) was performed to measure the muscle activities of the VMO and VL muscles during knee isometric extension exercises. The pulling sensor was used to maintain 70% of the maximum strength of the knee extensor continuously in the sitting position. After attaching the EMG sensor, the subjects were asked to perform isometric knee extension exercises randomly among three knee extension angles (90°, 135°, or 180°) in the sitting position. One-way repeated measures analysis of the variance and a Bonferroni post hoc test was used to identify the VMO and VL muscle activity during knee extension angles among 90°, 135°, and 180°. Results: The VMO and VL muscle activities increased with increasing knee extension angle in the sitting position (p<0.01). Conclusions: Knee extension exercise at a 180° angle in the sitting position can be recommended to increase the muscle activity of the VMO and VL muscle activities efficiently.

• 동굴
• /
• 제74호
• /
• pp.73-77
• /
• 2006

기술과학기술시추동경제여사회발전적동력, 촉진국제과기교류여합작시추동동북아지구경제발전적중요도경지일. 정부화민간적과기교류여합작시국제과기교류여합작적양익, 양자상호보충(兩者相互補充), 결일불가(缺一不可), 위촉진동북아지구경제여사회적발전, 건의(建議) : 충분발휘대학재동북아지구과기교류여합작중적주도작용 ; 충분발휘요저성재동북아지구과기교류여합작중적중요작용.

• Corrosion Science and Technology
• /
• 제19권2호
• /
• pp.51-56
• /
• 2020

The objective of this study was to improve properties of plasma sprayed HAp layer to titanium substrate by introducing an intermediate layer with two different methods. Before applying Zn doped HAp coating on titanium substrate, an intermediate layer was introduced by titanium plasma spray or titanium anodization. Heat treatments were conducted for some samples after titanium intermediate layer was formed. Zn doped HAp top layer was applied by plasma spraying. Three-point bending test and pull-off adhesion test were performed to determine the adhesion of Zn doped HAp coatings to substrates. Long-term credibility of Zn doped HAp plasma sprayed coatings on titanium was assessed by electrochemical impedance measurements in Hanks' solution. It was found that both titanium plasma sprayed and titanium anodized intermediate layer had excellent credibility. Strong adhesion to the titanium substrate was confirmed after 12 weeks of immersion for coating samples with titanium plasma sprayed intermediate layer. Samples with titanium anodized intermediate layer showed good bending strength. However, they showed relatively poor resistance against pulling off. The thickness of titanium anodized intermediate layer can be controlled much more precisely than that of plasma sprayed one, which is important for practical application.

• Advances in concrete construction
• /
• 제14권5호
• /
• pp.299-307
• /
• 2022

Cement-based matrixes have low tensile strength and negligible ductility. Adding fibres to these matrixes will improve their mechanical properties and make these composites suitable for structural applications. Post-cracking tensile strength of steel fibers-reinforced cementitious composite materials is directly related to the number of transverse fibers passing through the crack width and the pulling-out behavior of each of the fibers. Therefore, the exact recognition of the pullout behavior of single fibers is necessary to understand the uniaxial tensile and bending behavior of steel fiber-reinforced concrete. In this paper, an experimental study has been carried out on the pullout behavior of 3D (steel fibers with totally two hooks at both ends), 4D (steel fibers with a total of four hooks at both ends), and 5D (steel fibers with totally six hooks at both ends) in which the fibers have been located either perpendicular to the crack width or in an inclined manner. The pullout behavior of the mentioned steel fibers at an inclination angle of 0, 15, 30, 45, and 60 degrees and with embedded lengths of 10, 15, 20, 25, and 30 millimetres is studied in order to explore the simultaneous effect of the inclination angle of the fibers relative to the alongside loading and the embedded length of fibers on the pullout response in each case, including the maximal pullout force, the slip of the maximum point of pullout force, pullout energy, fiber rupture, and concrete matrix spalling. The results showed that the maximum pullout energy in 3D, 4D, and 5D steel fibers with different embedded lengths occurs at 0 to 30° inclination angles. In 5D fibers, maximum pullout energy occurs at a 30° angle with a 25 mm embedded length.

• 한국수산과학회지
• /
• 제11권1호
• /
• pp.39-48
• /
• 1978

본 연구에서는 3-course 구조와 2-course 구조의 랏쉘그물감을 선정하여 그 강도 특성을 조사하고, 이를 구성 섬유의 재료가 같은 매듭그물감 및 관통 그물감의 강도와 비교했다. 실험으로 부터 얻어진 결과를 요약하면 다음과 같다. 1. 랏쉘그물실의 강도가 랏쉘마디에서 감소하느 원인은 장력에 의한 마디의 변형 및 마디에서의 yarn 간의 마찰력에 주로 기인한다고 간주되며, 강도 감소율은 종인에서 $13\%$, 횡인에서 $22\~26\%$ 정도이다. 2. 랏쉘마디는 3-course 구조의 것이 2-course 구조의 것보다 모든 방향의 인장에서 약간 강하고, 마디 형태의 변형도 적다. 3. 주름을 준 상태에서의 랏쉘마디의 강도 $T_R$는 인접하는 다리가 이루는 각을 $\varphi$라 하면 $T_R=T_{R0}-k\varphi$ 로 주어진다. 단, $R_{R0}$는 $\varphi$가 $0^{\circ}$때의 $T_R$의 값, k는 상수이다. 4. 랏쉘그물감의 항장력 ${\sigma}R$ 및 파단에 소요되는 일량 $E_R$는 인장하는 쪽의 그물코 수를 N라 하면 ${\sigma}R=KN$ 또는 ${\sigma}R=K_RN$ 및 $E_R=AN$으로 표시되고, 파단신도는 N에 관계없이 거의 일정하다. 단, K 및 A는 상수이다. 5. 몇개의 다리가 미리 절단되어 있는 경우의 랏쉘그물감의 파단은 미리 절단되어 있는 다리에 인접한 다리의 마디로부터 일어나며, 그때의 항장력, 파단에 소요되는 일량 몇 파단신도의 감소는 비록 하나의 다리가 미리 절단되어 있는 경우라 할지라도 상당히 크다. 6. 랏쉘그물감의 파열강도는 두개의 다리를 인장한 경우의 랏쉘마디의 강도와 거의 같다. 7. 현용의 주된 세 종류의 그물감에 대해 그들을 구성하는 다리의 denier 수를 기준으로 하면, 관통마디가 가장 강하고, 매듭의 강도는 관통마디의 강도의 $69\~76\%$ 정도이다. 랏쉘마디는 종인시는 관통마디 강도의 $71\~74\%$ 로서 매듭과 거의 같은 강도를 가지지만, 횡인시는 매듭의 강도보다 약하여 $62\~67\%$를 나타낸다.

• Composites Research
• /
• 제31권4호
• /
• pp.139-144
• /
• 2018

장섬유강화 복합재료는 기존의 연속섬유강화 복합재료에 비해 우수한 생산 효율성과 복잡한 형상의 성형성에 대해 장점을 가지고 있다. 하지만 지나치게 복잡한 복합재료 형상을 제작하거나 서로 다른 재료로 제작된 부품들을 조립/체결해야 하는 경우 다양한 접합 방법들이 필요하다. 일반적으로 LFPS(Long Fiber Prepreg Sheet)는 성형 후 탈형을 쉽게 하기 위해 LFPS안에 이형제가 포함되어 있다. 그러므로 적절한 접합 강도를 위해 접착법과 더불어 기계적인 체결이 요구된다. 본 연구에서 열성형 공정을 통해 LFPS를 경화하고 스테인레스 강 인서트를 접착하는 동시경화 접착을 위한 스테인레스 강 인서트를 제안하였다. 성형공정 동안 펼쳐지는 스테인레스 강 인서트의 날개는 접착력과 기계적인 고정(Mechanical wedging)의 효과를 유발하여 인발력에 저항할 수 있는 갈고리 역할을 한다. 복합재료에 삽입된 인서트 날개들의 펼쳐진 상태를 확인하기 위해 소각 방법을 사용하였다. 그리고 접합 강도를 정량적으로 평가하기 위해 인발시험(Pull-out test)을 수행하였다. 이러한 실험들을 통해 가장 적절한 접합 강도를 보장하는 조건을 도출하였다.

• 한국안전학회지
• /
• 제10권3호
• /
• pp.81-95
• /
• 1995

Now, safety assurance in construction sites should be accomplished by its own organization rather than control of the code or government. It is believed that the safety assurance can be considerably improved by a lecture or an education using the existing theories or literatures up to now, but it is thought that fundamental safety assurance we not able to be accomplished without developing safety devices '||'&'||' equipment or taking fundamental measures, based on the result analyzed from workers behaviors. There are various behaviors of the workers showed in construction site, but only tests for hammerusing works such as form, re-bar, stone workers directly related to the grip strength are mainly performed, investigated and measured here for the study. The above works are similar to power grip, 7th picture on seven items which are categorized for hand grip types(Ammermin 1956 ; Jones ; Kobrick 1958). Measurements of grip strength are commonly taken in anthropometric surveys. They are easy to administer but unfortunately it is rather dubious whether they yield any data that are of interest to the engineer. Very fewer controls of tools are grasped and squeesed studies showed very little overall correlation between grip strength and other measures of bodily strength (Laubach, Kromer, and Thordsen 1972), but hammer-using work which is practically progressed in construction site are mainly influenced with grip strength. According to the investigation on work measurement, it is shown that 77% of form worker are using hammer to be related to grip strength. In this study, it is particularly noticed that wearing safety gloves in construction site is required for workers safety but 20% difference between grip strength with safety gloves and without ones are commonly neglected in the site(Fig. 1). Nevertheless, safety operation with consideration of the above 20% difference is not considered in the construction site. Factors of age, kinds of work, working time, with or without safety gloves are in vestigated '||'&'||' collected at the sites for this study. Test, not at each working hour but at 14 : 00 when the almost all of the workers think the most tired, resulting from the questionaires, also when it is shown on the research report has been performed and compared for main kinds of works : form '||'&'||' re-bar work. Tests were performed with both left SE rightand of the workers simultaneously in construction site using Rand Dynamometer(Model 78010, Lafayette Instrument Co., Indiana, U.S.A) by reading grip strength on the gauge while they are pulling, and then by interviewing on their ages, works, experiences and etc., directly. The above tests have been performed for the dates of 15th march-26th May '95 with consideration of site condition. And even if various factors of ambient temperature on the testing date, working condition, individual worker's habit and worker's condition of the previous ate are concerned with the study. Those are considered as constants in this study. Samples are formwork 53, rebar 62, electrician 5, plumber 4, welding 1 from D construction Co., Ltd, ; formwork 12, re-bar 5, electrician 2, from S construction Co., Ltd, , formwork 78, re-bar 18, plumber 31, electrician 13, labor 48, plumber 31, plasterer 15, concrete placer 6, water proof worker 3, maisony 5 from B construction Co., Ltd. As In the previously mentioned, main aspect to be investigated in this study will be from '||'&'||' re-bar work because grip strength will be directly applied to these two kinds of works ; form '||'&'||' re-bar work, eventhough there are total 405 samples taken. It is thought that a frequency of accident occurrence will be mainly two work postures "looking up '||'&'||' looking down" to be mainly sorted, but this factor is not clarified in this study because It will be needed a lot of work more. Tests has been done at possible large scale of horizontally work-extended sites within one hour in order to prevent or decrease errors '||'&'||' discrepancies from time lag of the test. Additionally, the statistical package computer program SPSS PC＋has been used for the study.

• Current Photovoltaic Research
• /
• 제4권3호
• /
• pp.124-129
• /
• 2016

Recently industry has voiced a need for optimally designing the production process of low-cost, high-quality ingots by improving productivity and reducing production costs with the Czochralski process. Crystalline defect control is important for the production of high-quality ingots. Also oxygen is one of the most important impurities that influence crystalline defects in single crystals. Oxygen is dissolved into the silicon melt from the silica crucible and incorporated into the crystalline a far larger amount than other additives or impurities. Then it is eluted during the cooling process, there by causing various defect. Excessive quantities of oxygen degrade the quality of silicone. However an appropriate amount of oxygen can be beneficial. because it eliminates metallic impurities within the silicone. Therefore, when growing crystals, an attempt should be made not to eliminate oxygen, but to uniformly maintain its concentration. Thus, the control of oxygen concentration is essential for crystalline growth. At present, the control of oxygen concentration is actively being studied based on the interdependence of various factors such as crystal rotation, crucible rotation, argon flow, pressure, magnet position and magnetic strength. However for methods using a magnetic field, the initial investment and operating costs of the equipment affect the wafer pricing. Hence in this study simulations were performed with the purpose of producing low-cost, high-quality ingots through the development of a process to optimize oxygen concentration without the use of magnets and through the following. a process appropriate to the defect-free range was determined by regulating the pulling rate of the crystals.

• 대한관절경학회지
• /
• 제6권1호
• /
• pp.60-63
• /
• 2002

목적 : 네 겹의 슬괵건을 이용한 전방십자인대 재건술시 대퇴터널을 횡고정 핀과 흡수성 간섭나사로 함께 고정하는 수기를 소개하고자 한다. 수술 술기 : 반건양건과 박건을 채취하여 네 겹으로 준비하였다. 경골터널과 대퇴터널을 만드는데 대퇴터널의 깊이는 35 mm로 하였다. Rigidfix system의 가이드를 삽입하고 가이드의 위쪽 관에만 구멍을 내었다. 이식건을 통과시킨후 횡고정 핀 을 고정하였다. 이후 이식건을 경골쪽으로 당기면서 흡수성 간섭 나사로 고정하였다. 결론 : 슬괵건 전방십자인대 재건술시 횡고정 핀과 흡수성 간섭나사를 이용한 대퇴터널 고정은 강한 초기 고정과 이식건의 골통합을 촉진시킬 수 있는 좋은 방법으로 사료되어 소개하였다.

• International Journal of Concrete Structures and Materials
• /
• 제11권2호
• /
• pp.215-228
• /
• 2017

A new approach for measuring the specific fracture energy of concrete denoted modified disk-shaped compact tension (MDCT) test is presented. The procedure is based on previous ideas regarding the use of compact tension specimens for studying the fracture behavior of concrete but implies significant modifications of the specimen morphology in order to avoid premature failures (such as the breakage of concrete around the pulling load holes). The manufacturing and test performance is improved and simplified, enhancing the reliability of the material characterization. MDCT specimens are particularly suitable when fracture properties of already casted concrete structures are required. To evaluate the applicability of the MDCT test to estimate the size-independent specific fracture energy of concrete ($G_F$),the interaction between the fracture process zone of concrete andthe boundary of theMDCTspecimens at the end of the test is properly analyzed. Further, the experimental results of $G_F$ obtained by MDCT tests for normal- and high-strength self-compacting concrete mixes are compared with those obtained using the well-established three-point bending test. The procedure proposed furnishes promising results, and the $G_F$ values obtained are reliable enough for the specimen size range studied in this work.