• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.6
• /
• pp.28-36
• /
• 2018

A study was conducted to apply open-loop control to the combustion instability in a dump combustor using gaseous hydrocarbon fuels. Control power and frequency were varied by employing a loudspeaker under combustion conditions with similar characteristic chemistry times of the fuels. In the case of open-loop control where the frequency was identical to the combustion instability frequency, the open-loop control power affected the control performance. Results obtained from conducted open-loop control tests, where the frequency was different from the combustion instability frequency, show that setting the open-loop control frequency similar to the combustion instability frequency is effective.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.11
• /
• pp.1640-1646
• /
• 2013

Conventional power conversion unit that is a major part of the propulsion system has applied GTO thyristor as a switching semiconductor device of main circuit since introduction of the 8200 electric locomotive. But problem that quick maintenance is difficult and its cost is increasing occurs because major components of the power conversion unit are slowly discontinued. To solve these, in this paper, it was analyzed the response characteristic of the propulsion system modeling of the 8200 electric locomotive using IGBT which is applied recently to ensure propulsion control technology. As results of response for a Propulsion system modeling, it show that a power conversion unit is controlled by PLL(Phase-locked loop) and SVPWM(Space Voltage PWM) respectively.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.4 s.247
• /
• pp.306-313
• /
• 2006

Automated material handling system is being used as a method to reduce manufacturing cost in the semiconductor and flat panel displays (FPDs) manufacturing process. Those are considering switch-over from the traditional cassette system to single-substrate transfer system to reduce raw materials of stocks in the processing line. In the present study, the wafer transportation speed has been evaluated by numerical and experimental method for three propulsion nozzle array (face, front, rear) in an air levitation system. Test facility for 300 mm wafer was equipped with two control tracks and a transfer track of 1,500mm length. The diameter of propulsion nozzle is 0.8mm and air velocity of wafer propulsion is $50\sim150m/s$. We found that the experimental results of the wafer transportation speed were well agreed with the numerical ones. Namely, the predicted values of the maximum wafer transportation speed are higher than those values of experimental data by 16% and the numerical result of the mean wafer transportation speed is higher than the experimental result within 20%.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.437-441
• /
• 2008

A non-toxic Post Boost Stage(PBS) with LOX/Ethanol engine was successfully demonstrated at the Tomioka Facility of IHI Aerospace. IHI Aerospace has researched and developed the nontoxic propulsion systems and the LOX/Ethanol is one of the most attractive non-toxic bipropellant candidates. ${\rho}ISP$ of LOX/Ethanol is higher than ${\rho}ISP$ of the other non-toxic bipropellants as LOX/HC or $LOX/LH_2$. The authors studied the combustion characteristics of LOX/Ethanol propellant with the engine designed for LOX/LNG propellant. Also the injector with a built-in igniter was designed and examined its feasibility, ignition and combustion characteristics. We have demonstrated Post Boost Stage with future LOX/Ethanol engines. This propulsion system is targeted for expandable vehicle upper stage to accelerate delta-V to reach the required orbit. PBS Demonstration Model is designed as a test stand to evaluate feed system for integrated propulsion system and also to demonstrate Integrated Vehicle Health Management(IVHM) technique using local valve control and also valve behavior-monitoring capability.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.10
• /
• pp.992-997
• /
• 2010

The Propulsion Control Module(PCM) of Hall-thruster Propulsion System(HPS) for Science and Technology Satellite-3 (STSAT-3) has the flow control accuracy of less than ${\pm}$3% and the pressure control accuracy of less than ${\pm}$5%. The pressure controller adjusts pressure around the set point by using a Proportional Flow Control Valve (PFCV) and a high pressure transducer, while the flow controller regulates the flow rate using PFCV and the anode current telemetry of the Hall Thruster. The controllers are chosen as the Proportional and Integral(PI) type, and the PI gains are tuned based on the Matlab simulations. The result of the PCM test had the flow control accuracy of less than ${\pm}$1.87% and the pressure control accuracy of less than ${\pm}$5%. This paper describes the design, realization, and performance test results of the PCM.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.1
• /
• pp.55-62
• /
• 2011

In this study, we tried to improve the thrust control performance through the thrust control combustion experiment of the hybrid rocket. We constructed the system which controls the oxidizer flow by combining a needle valve with a stepping motor and controlling the stepping motor drive according to the thrust control command order. Gas oxygen was used as the oxidizer for two different propellants, PE(Polyethylene), PC(Polycarbonate), respectively. To improve the slow response time and the oscillation phenomenon in the beginning stage of the thrust control combustion experiment, we measured and analyzed the change of the flow speed of the propellant pipe. The revised thrust control combustion experiment showed that the thrust was stably controlled with the margin or error from the thrust command within ${\pm}1$ N.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.734-741
• /
• 2004

Boundary layer ingestion in airframe-integrated scramjet engines causes engine stall (“engine un start” hereafter) and restricts engine performance. To improve the unstart characteristics in engines, boundary layer bleed and a two-staged injection of fuel were examined in Mach 4 and Mach 6 engine tests. A boundary layer bleed system consisting of a porous plate, an air coolers, a metering orifice and an ON/OFF valve, was designed for each of the engines. First, a method to determine bleed rate requirements was developed. Porous plates were designed to suck air out of the Mach 4 engine at a rate of 200 g/s and out of the Mach 6 engine at a rate of 30 g/s. Air coolers were then optimized based on the bleed airflow rates. The exhaust air temperature could be cooled below 600 K in the porous plates and the compact air coolers. The Mach 4 engine tests showed that a small bleed rate of 3% doubled the engine operating range and thrust. With the assistance of two-staged fuel injection of H2, the engine operating range was extended to Ф0.95 and the maximum thrust was tripled to 2560 N. The Mach 6 tests showed that a bleed of 30 g/s (0.6% of captured air in the engine) extended the start limit from Ф0.48 to Ф1 to deliver a maximum thrust of 2460 N.

• Journal of the Korea Society of Computer and Information
• /
• v.28 no.9
• /
• pp.149-158
• /
• 2023

With the global paradigm shift towards climate change, the shipbuilding industry is also considering propulsion systems that utilize eco-friendly fuels various propulsion systems are gaining attention as a result. In conventional propulsion systems, typically consisting of propellers and rudders, have evolved into a diverse range of systems due to the development of a special propulsion system known as the azimuth thruster. While azimuth thrusters were previously commonly installed on tugboats, they are now extensively used on offshore plant operation ships equipped with dynamic positioning systems. However, these azimuth thrusters require different steering methods compared to conventional propulsion systems, leading to a significant learning curve for the crew members boarding such vessels. Furthermore the availability of education related to these special propulsion systems is limited. This study aims to analyze accidents caused by inadequate control of vessels equipped with azimuth thrusters using the STAMP technique. And it proposes the necessity of standard steering commands for the safe operation of vessels equipped with special propellers.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.1
• /
• pp.429-435
• /
• 2015

This study proposes a re-adhesion algorithm that has stable traction effort for rolling stock slip/slide minimization when deliverable traction decreases by slip. The proposed scheme estimates appropriate reference speed using two encoders for reducing slip and controls traction effort stably and has stable control characteristics for disturbance. The algorithm which uses the maximum adhesive effort by instantaneous estimation of adhesion force stably controls traction effort and gives rolling stock excellent acceleration and deceleration characteristics. And a slip sensing element that can quickly detect slip is used. Load motor and inverter were checked in various slip conditions for creating various line conditions.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.8-13
• /
• 2011

본 연구에서는 대형 로켓엔진시스템의 시동 시 안정적인 유량공급을 위한 제어기 설계가 이루어졌다. 펌프, 오리피스, 제어밸브, 파이프, 인젝터 및 재생 냉각채널과 같은 엔진시스템 구성품들에 대한 동특성 모델링을 수행하였고 유량공급 제어가 가능한 밸브의 구동신호를 조절 가능한 PID 제어기를 설계하였다. 시동 시 안정적인 유량공급을 위하여 실험을 통해 얻은 밸브의 적정 개도율을 적용시켰으며, 이를 기준으로 하여 제어밸브의 작동신호를 조절하여 유량비를 제어하였다. 시뮬레이션 한 결과 제어기를 통해 시동 시 정상추력까지 유량공급을 제어 하는 방법이 적절함을 확인하였다.