• 동력기계공학회지
• /
• 제7권1호
• /
• pp.68-73
• /
• 2003

The purpose of this study is to develop a new proportional pressure reducing valve and to verify the validity of a new mechanism with pressure control pin. The dynamic characteristics of the object pressure reducing valve was studied by numerical analysis of the mathematical model. Also, static and dynamic characteristics of the new pressure control valve were tested with a testing system based on the test standard.

• 한국자동차공학회논문집
• /
• 제2권3호
• /
• pp.75-84
• /
• 1994

In general direct-operated pressure reducing valves have been gardly applied to a dynamic control system such as active suspension control because of their poor control stability. But they are more robust than pilot-operated type and do not need pilot control flow. In this paper development of a new direct-operated proportional pressure reducing valve for low-band type active suspension control is reported. By means of a special damper directly linked to the valve spool, the control stability could be effectively improved without drawback in response time. The linearity error was less than $\pm$3.5%. Applied to an experimental active suspension system the new valve showed the $-90^{\circ}$ phase delay at 4Hz with 20% sinusoidal signal input and could control the suspension system with almost same performance as that with a pilot-operated type valve.

• 드라이브 ㆍ 컨트롤
• /
• 제18권4호
• /
• pp.1-8
• /
• 2021

An electro proportional pressure control valve is mainly used to control the clutch of an agricultural tractor's automatic transmission. During transmission, the operating, hydraulic oil is mix with many kinds of contaminants. The contaminants can be trapped between the valve body and spool of the proportional pressure control valve leading to abnormal operating conditions and finally critical damage to the transmission hydraulic system. The present study aimed to verify the valve control algorithm as a basic study of developing control logic that removes contaminants between the spool and the body of the proportional pressure control valve. To develop the algorithm, MATLAB/SIMULINK was used. PWM method was used to control the applied solenoid coil current. The effectiveness of the algorithm was verified by comparing the actual pressure of the normal valve with the actual pressure of the abnormal valve. Based on the present study findings, when the algorithm was applied, the response of the valve pressure according to the current became stable and oil contaminated particles were removed. In the future study, the control algorithm will be optimized for the stability of the proportional pressure reducing valve, and it will be verified in consideration with the driving of the clutch.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.1305-1306
• /
• 2010

• 한국정밀공학회지
• /
• 제5권3호
• /
• pp.81-90
• /
• 1988

In recent, the requirement of remote control of hychaulic system is in- creasing. The actuator unit whose output position is proportional to input electrical signal needs a pressure reducer and a dump valve. The pressure reducer provides a constant regulated pressure and filters contaminants. The dump valve supplies proper pressure to the pressure reducer and unloads when the system is not operated. In this thesis, dump valve and pressure reducer with auxiliary function are studied. The choke in the pressure reducer prevents actuator from supplying higher pressure than necessary pressure at beginning, and the spring constant affects on the dynamic characterisics. In dump valve, it is proved that diameter of servo-slide hold and choke diameter of dump plunger affects on damping response.

• 드라이브 ㆍ 컨트롤
• /
• 제16권2호
• /
• pp.30-35
• /
• 2019

EPPR (Electro-hydraulic Proportional Pressure Reducing) valves are pressure control valves. In this study, an independent metering valve (IMV), which is a combination of a spool valve opened and closed with the help of an EPPR valve, was discussed. The overall performance of the valve (IMV) was obtained by the respective modeling and simulation of the system. The valve investigated in this study is to be used for independent metering of hydraulic excavator actuator e.g. boom, arm, bucket etc. To design the model, continuity equations and force balance equations were used. The set of differential equations were then simulated in Simulink using ODE45 option in the configuration toolbox. The valve has to be able to control the flow rate going in and out of the cylinder separately, which is why the particular configuration was needed and selected.

• 드라이브 ㆍ 컨트롤
• /
• 제15권2호
• /
• pp.46-51
• /
• 2018

Many research studies have been carried out related to saving energy and environmental pollution in the field of construction machinery. The best solution for reducing the related environmental pollution is to reduce fuel consumption by upgrading the energy efficiency of machinery used in this field. An efficiency upgrade in the field of construction machinery would mean minimizing the pressure loss in hydraulic pipe lines or achieving optimal operating conditions while responding to a load. One way to achieve this is to make an equivalent circuit, like an electrohydrostatic actuator, or to improve the spool type valve using the 4/3 way method. This study deals with an electrohydraulic proportional flow control valve. SimulationX software is used as a simulation tool for analyzing the dynamic characteristics. The analysis results, including the performance and characteristics of design parameters, are discussed and the validity of the theoretical analysis is also evaluated.

• 한국자동차공학회논문집
• /
• 제14권6호
• /
• pp.160-170
• /
• 2006

If hydraulic pump controlled by mechanical type regulator has more than one control function, the construction of regulator will be very complicated and control performance falls drastically. It is difficult to have more than one control function for hydraulic pump controlled by electronic type hydraulic valve due to the inconsistency of controllers. This paper proposes a multi-function control technique which controls continuously flow, pressure and power by using EPPR(Electronic Proportional Pressure Reducing) valve in swash plate type axial piston pump. Nonlinear mathematical model is developed from the continuity equation for the pressurized control volume and the torque balance for the swash plate motion. To simplify the model we make the linear state equation by differentiating the nonlinear model. A reaction spring is installed in servo cylinder to secure the stability of the control system. We analyze the stability and disturbance by using the state variable model. Finally, we review the control performances of flow, pressure and power by tests using PID controller.

• 한국자동차공학회논문집
• /
• 제5권5호
• /
• pp.20-26
• /
• 1997

A System for reducing vehicle body roll by active control is developed. The stabilizer bar with hydraulic rotary actuator produces anti-roll moment which suppresses roll tendency. This reduction of roll improves the driving safety as well as the ride comfort. Vehicle test data shows considerable reduction of roll angle during steady-state turning. Also improvement of ride comfort is achieved by making the actuator freely rotatable, i.e. by connecting all chambers of actuator in normal driving conditions. A control algorithm using steering wheel angle and vehicle speed signal as input valve is applied. It is compared with signal of the G-sensor.

• 한국정보통신학회논문지
• /
• 제7권5호
• /
• pp.1026-1031
• /
• 2003

자동 급수펌프는 압력스위치에 의해 운전 및 정지를 하게 된다. 따라서 수량 증감에 따른 펌프의 빈번한 운전 및 정지로 인해 지속적인 정격 및 정압 운전이 불가능하다. 또한 빈번한 작동으로 인해 지속적으로 일정한 압력을 얻을 수 없으며, 펌프의 소손과 에너지의 낭비가 심한 단점을 가지고 있다. 본 논문에서는 이러한 단점을 해결하고자 급수밸브, 유량센서, 제어장치로 구성되는 정압 급수장치를 설계 제작하였다. 급수밸브는 유출되는 물의 양과 관계없이 항상 일정한 양의 물을 유입하여 펌프의 부하를 줄이는 역할을 한다. 유량센서는 적외선 다이오드를 사용하여 유출되는 물의 양의 측정하며, 제어장치는 8 비트 마이크로프로세서를 이용하여 설계하였으며, 특별한 제어 알고리듬에 의해 펌프의 운전과 정지를 제어하게 하였다. 본 논문에서 개발한 장치는 토출 압력이 일정하게 유지되고 펌프의 작동 및 정지 동작이 부드럽게 이루어지며, 펌프의 지속적인 정압운전이 가능하므로 기존의 단점을 보완하는 장치로 사료된다.