• International Journal of Highway Engineering
• /
• v.17 no.3
• /
• pp.49-58
• /
• 2015

PURPOSES : The use of environmentally friendly construction methods has been recently encouraged to reduce fuel consumption and the effects of global warming. For this purpose, the roller compacted concrete pavement (RCCP) construction method has been developed. RCCP is more environmentally friendly and economically efficient than general concrete by reducing the amount of CO2 generated through the application of a smaller amount of cement. RCCP has a number of advantages such as an easy construction method, low cost, high structural hydration performance, and aggregate interlocking. However, mix design standards and construction guidelines of RCCP are required for domestic application. In addition, a study on aggregate selection, which has an effect on the characteristics of RCCP, is necessary owing to a limited number of researches. Thus, the aggregate effect on the performance of RCCP in securing the required strength and workability was evaluated in consideration of domestic construction. METHODS : Sand and coarse aggregates of both 19mm and 13mm in maximum size were used in this study. Four types of aggregate gradations (s/a = 30%, 58%, and 70% for the sand and coarse aggregate of 19mm in maximum size, and s/a = 50% for a combination of the three types of aggregates) were set up to investigate the effects of the PCA band on the RCC characteristics. The conditions of s/a = 30% and 70% were evaluated to check the gradation effect outside of the recommended band. The conditions of s/a = 58% and 50% were used because they are the optimum combination of the two and three types of aggregates, respectively. RCCP gradation band was suggested gradation with a proper construction method of RCCP by synthetically comparing and analyzing the correlation of optimum water content, maximum dry density, and strength of requirements through its consistency and compaction test. RESULTS : The lower and upper limit lines are insufficient to secure a relatively strong development and workability compared to an aggregate gradation in the RCCP gradation band region. On the other hand, the line in the RCCP gradation band and the 0.45 power curve in the RCCP gradation band region were satisfactory, ensuring the required strength and workability. CONCLUSIONS : The suitable aggregate gradation on RCCP process should meet the RCCP gradation band area; however, fine particles passing through a #60 sieve do not need to be within the recommended gradation band because the influence of this region on such fine particles is small.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.24 no.6
• /
• pp.599-615
• /
• 2022

In order to excavate underground tunnel most safely such as Han river, the slurry shield TBM method is applied to cope with face of high water pressure for many metro projects. In downtown subway project most of excavated soil is discharged externally whereas in road construction excavated soil is used as filling materials so it becomes important factor for success of the project. After excavated soil, weathered rock and soft rock are discharged with bentonite through discharge pipe to slurry treatment plant then those soils are separated in separation plant according to those size. Fine grained soil has been discarded together with filter cake but it is not toxic and can be mixed with coarse aggregate in proper ratio so this study is performed to find use of qualified filling material to meet quality standard. Therefore, in this study, legal standards and quality standards for the utilization of excavated soil of the slurry shield TBM method were examined and test was conducted to derive recycling way for filter cake and aggregate. And a plan for using it as a filling material for road construction was derived. Because bentonite is a clay composed of montmorillonite, and the excavated soil in the tunnel is also non-toxic, disposal of this material can waste social cost so it is expected to be helpful in the underground space development project that carries out the TBM project by recycling it as a valuable resource.

• The Journal of Fisheries Business Administration
• /
• v.33 no.1
• /
• pp.43-68
• /
• 2002

In the fisheries industry, the cost of oil Is the greatest factor, contributing 25% 40% of the cost of production. In order to support fisheries, the government has supplied large amounts of money for oil to the fisheries industry. However, the elimination and restriction against the subsidy of fisheries has been actively discussed throughout international organizations Including the WTO. The purpose of this thesis is to study the existing issue of subsidies on the fisheries Industry, which is currently disputed in international organizations, and predict a future policy about the oil supply that considers the most important factors on fisheries. In chapter 2, the paper begins by outlining the tendencies of discussion in relation to the subsidy on fisheries among international organizations, and categorizes them on the basis of their types. Chapter 3 defines the current conditions and characteristics of the Korean subsidy on fisheries and analyzes which portions of the subsidy on fisheries should be eliminated first when it is prohibited. In chapter 4, procedures and problems for producing tax-free oil are discussed, because tax-free oil has a higher possibility of being ruled out. Chapter 5 proposes a reasonable plan concerning oil supply policies for maintenance or enrichment of the fishing industries, post the elimination of subsidies. Conclusions were drawn in eight areas as a result of this study: 1) securing the large storage of oil, 2) extending customers of oil to include non-fishermen, 3) coordinating the segmentation of marketing area, 4) diversification of the sales goods, 5) producing oil sales experts, 6) developing original brands, 7) expanding the purchasing area to buy oil in the international market, and 8) operating funds to stabilize oil price. It would not be appropriate to wait until international organizations decide to ban the subsidy of fisheries. Corresponding plans ( such as securing the large storage of oil) tend to be large scale and long-term projects because they take a number of years, from designing the oil storage tank to selecting the proper region and initiating the construction. Therefore, it is strongly suggested that any extensive and time consuming projects including preparation for the tax-free oil should be completed in new actions before the ban by the international organizations.

• Journal of Korean Society of Steel Construction
• /
• v.24 no.1
• /
• pp.109-117
• /
• 2012

This study seeks to devise a design application for a beam structure with partially restrained composite connection to a CFT column. A cost-efficient and stable component is applied by adjusting the stiffness ratio of the column connection through partially restrained composite connection. Based on a review of the structure's stability, it was confirmed that in the case of a low-rise building as a moment frame, resistance without bracing is feasible because stiffness increased by virtue of the partial restrained composite connection by composite action. In the case of a high-rise building, lateral resistance load of moment frame was approximately 10% when proper partial restrained rate was at around 60%. With considerations related to economic efficiency, the partial restriction effect of the beam component was significantly activated by the uniform load, but that of the beam activated by concentrated load was not significantly indicative. The analysis indicated that 60% partial restrained girder at the connection was the most economical in the case of uniform load. It also showed that end moments can be reduced by approximately 25%.

• Journal of Korea Port Economic Association
• /
• v.31 no.3
• /
• pp.107-120
• /
• 2015

International logistics systems for cross-border trading aim not only to reduce costs and time, but also to maximize added value. For accuracy of shipping time, cost reduction, rapidity, and safety improvement, demand for Ro-Ro shipping as a global supply chain operating system has increased. To anticipate these demands, this study estimates the optimal demand and scale of Ro-Ro berth construction by analyzing shipping volumes between Korea and Japan. Based on Ro-Ro shipping speeds and distances between Korea and Japan, the shipping volume (container and general cargo) of Busan port is sorted into two separate zones. After analyzing the ratio of items that have great potential benefits from using Ro-Ro shipping, we estimate possible shipping volumes using Ro-Ro berth provision. The results reveal that two berths for 20,000t vessels are additionally required to accommodate the estimated volume. Results suggest the construction of an exclusive Ro-Ro berth in Busan port. This would not only accommodate the demand between Korea and Japan, but also provide a way to avoid the lean-to-one-side port policy.

• Steel and Composite Structures
• /
• v.19 no.2
• /
• pp.277-292
• /
• 2015

Previous research has shown that steel plate shear walls (SPSWs) are efficient lateral force-resisting systems against both wind and seismic loads. A properly designed SPSW can have high initial stiffness, strength, and energy absorption capacity as well as superior ductility. SPSWs have been commonly designed with unstiffened and stiffened infill plates based on economical and performance considerations. Recent introduction and application of corrugated plates with advantageous structural features has motivated the researchers to consider the employment of such elements in stiffened SPSWs with the aim of lowering the high construction cost of such high-performing systems. On this basis, this paper presents results from a numerical investigation of the hysteretic performance of SPSWs with trapezoidally corrugated infill plates. Finite element cyclic analyses are conducted on a series of flat- and corrugated-web SPSWs to examine the effects of web-plate thickness, corrugation angle, and number of corrugation half-waves on the hysteretic performance of such structural systems. Results of the parametric studies are indicative of effectiveness of increasing of the three aforementioned web-plate geometrical and corrugation parameters in improving the cyclic response and energy absorption capacity of SPSWs with trapezoidally corrugated infill plates. Increasing of the web-plate thickness and number of corrugation half-waves are found to be the most and the least effective in adjusting the hysteretic performance of such promising lateral force-resisting systems, respectively. Findings of this study also show that optimal selection of the web-plate thickness, corrugation angle, and number of corrugation half-waves along with proper design of the boundary frame members can result in high stiffness, strength, and cyclic performances of such corrugated-web SPSWs.

• Journal of the Korea Institute of Building Construction
• /
• v.20 no.2
• /
• pp.155-162
• /
• 2020

Since the third industrial revolution has been started in the 1980s, the form of buildings has been varied and atypical by the development of building technology. Such free-form building has a curved shape unlike the existing standard buildings, and to realize this, it is necessary to manufacture the free-from panel. The shape of the free-form panel must satisfy a limited error ratio compared with the design shape, and the technology to produce free-form panels is very difficult. However, there are many problems such as enormous cost and construction waste generation when implementing free-from construction. Therefore, the development of free-form panel manufacturing technology should be made to solve the problems caused by the free-form construction. In this study, the error rate analysis of the mixed mortar panel was conducted by selecting the proper mixing ratio of the mixed mortar for the shape of the free-form panel.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.7 no.1
• /
• pp.53-66
• /
• 1999

Limited landfill area and finance as well as a large generation of food wastes, have called for systematic approaches towards potential cost savings. In this study, the regional management system of food wastes generated from the residential and commercial sources was considered in three cities bounded each other; Changwon, Masan, and Jinhae city. Total thirteen alternatives were established and compared by applying the WRAP (Waste Resource Allocation Program). The following results were obtained: 1. While relatively small amounts were generated from the commercial sources such as cafeteria, restaurants, and market facilities, almost 80% of food wastes were generated from the residential sources. 2. Unit costs for food waste management in three cities were different according to their present situation such as the type and location of major generation sources and treatment facilities. Especially, the highest cost appeared in Jinhae city due to the most expensive construction of coastal landfill site. 3. Considering proper revenue, the whole conversion of food waste into animal feed was selected as the optimal alternative and represented 60% to 74% of the management cost of the whole landfill alternative in all cities. Comparing the other alternatives, composting of food waste was more economical than landfill alternative and the incineration was the most expensive alternative. 4. Some of the regional management systems using common food waste processing facilities together in three cities showed to be more economical than the single management system. Therefore, more detailed research for the regional management systems of food waste was recommended.

• Journal of Environmental Policy
• /
• v.9 no.1
• /
• pp.83-107
• /
• 2010

Urbanized environments are constructed to estimate peak flow and cost savings in response to possible BMP allocation at a watershed scale. The main goal is to explore the proper allocation of sub-watershed level BMPs for peak flow attenuation at a watershed scale. Since several individual site scale BMPs work as a form of aggregated BMPs at a sub-watershed scale, it is a question as to how to properly allocate the sub-watershed level BMPs at a watershed scale. The Hydrological Simulation Program-FORTRAN (HSPF) is set up for a hypothetically urbanized watershed. A peak flow is determined to be the primary variable of interest and targeted to characterize the spatial distribution of aggregated BMPs. Construction cost of a regional pond forms the basis of the economic valuation. The results indicate that when total size of BMPs is constant in the entire watershed, (1) it is most effective to have aggregated BMPs in some upper sub-watersheds while the BMPs in either the mainstem sub-watershed or a single sub-watershed are the least effective choices for peak flow attenuation at a watershed scale; (2) savings exist between allocation differences and reduced peak flow increases cost savings. The largest saving is found in the strategy of aggregated BMPs in some upper sub-watersheds. These findings, however, call for follow-up site specific case studies revisiting the watershed scale impacts of BMP allocation. Then, it will be argued that location and extent of decentralization are considerable policy variables for an alternative stormwater management policy at a watershed scale.

• Korean Journal of Construction Engineering and Management
• /
• v.16 no.4
• /
• pp.118-128
• /
• 2015

Recently BIM technology has been expanded for using in construction project. Due to the high-cost of BIM infrastructure development, lack of regulations, lack of process and so forth, usage of BIM has been delayed than initial expectations. In design phase, especially, collaboration based on BIM system has been a key factor for successful next generation building project. Through the analysis of current research trends about IT technologies, virtualization and BIM service, data exchange such as drawings, 3D model, object data, properties using cloud computing and virtual server system is defined as a most successful solution. The purpose of this study is to enable the cloud computing BIM server to provide several main functions such as editing models, 3D model viewing and checking, mark-up and snapshot in high-performance quality by proper design of VDI system. Concurrent client connection performance is a main technical index of VDI. Through testing of test-bed server client, developed VDI system's multi-connect control is evaluated. Performance-test result of BIM server VDI effect to development direction of cloud computing BIM service for commercialization.