• Journal of the Society of Naval Architects of Korea
• /
• v.38 no.4
• /
• pp.1-10
• /
• 2001

A numerical solution method of the incompressible Reynolds-Averaged Navier-Stokes equations is applied for calculating turbulent flows and performances of a marine propeller in open-water, four-quadrant conditions. Computed propeller flows of the model propeller P4381, for which the experimental data of the open-water performances exist, reveal complex viscous-flow characteristics including three-dimensional flow separations in various off-design conditions and also computed propeller thrusts and torques agree quite well with experimental data except some cases for which severe propeller cavitations occurred in the experiment.

• Journal of the Society of Naval Architects of Korea
• /
• v.54 no.1
• /
• pp.10-17
• /
• 2017

This paper deals with a comparison of performance between tip rake propeller and normal propeller in P.O.W condition. In comparison with normal propeller, tip rake propeller is good at preventing occurring negative effect: tip vortex, etc. But, officially formulated information about tip rake propeller doesn't become known. So this paper makes design variables about rake factors and applies them to propeller geometry. And propellers applied design variables are compared with each other about open water propeller efficiency. Also this paper confirms a vorticity reduction at propeller tip.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.3
• /
• pp.296-303
• /
• 2014

The Axiom propeller is a unique 3 bladed propeller and it enables to generate the same amount of thrust going ahead as it does going astern because of its 's' type skew-symmetric blade section. A earlier variant of the design (Axiom I propeller) performed a low propeller efficiency, maximum 35 % efficiency, and further blade outline design was carried out to achieve a higher efficiency. The optimized new blade outline (Axiom II propeller) has more conventional Kaplan geometry shape than Axiom I propeller. Model tests of open water performance and propeller cavitation for both propellers were conducted at Emerson Cavitation Tunnel in order to compare their performances. Experiment results revealed that Axiom II propeller provides a maximum 53 % efficiency and provides better efficiency and cavitation performance over the Axiom I propeller under similar conditions.

• Journal of Ocean Engineering and Technology
• /
• v.21 no.3 s.76
• /
• pp.40-45
• /
• 2007

This study was performed to investigate the effect of various propeller tunnel shapes on the propulsion performance of a fishing boat. The propeller tunnel reduces the problem resulting from the open propeller accidentally catching the waste net and cable on the sea, as well as increasing the cruising speed. For 3 different tunnel geometries, the model test is conducted in the circular water channel, and the potential based panel method was applied to analyze the hydrodynamic characteristics of propeller. Also, both results are compared with each other to represent the difference between results of the model scale test and the potential theory. It is expected that these results could be referenced in the design of the propeller tunnel in consideration of the hydrodynamic interaction between the propeller and the tunnel.

• 한국전산유체공학회:학술대회논문집
• /
• 2009.11a
• /
• pp.77-83
• /
• 2009

In this study, we conducted resistance and propulsion performance test of ship composed of the Resistance Test, Propeller Open Water Test and Self Propulsion Test using the CFD(Computational Fluid Dynamics). We used commercial RANS(Reynolds Averaged Navier Stokes equation) solver, as a calculating tool. The unstructured grids were used in a bow and stern of ship, having complex shape, for a convenience of generating grids, and the structured grids were adopted in a central hull and rest of hull having a relatively simple shape which is called hybrid grid method. In addition, The sliding mesh method was adopted to rotate a propeller directly in the Propeller Open Water and Self Propulsion Test. The Resistance Test and Self Propulsion Test were calculated using Volume of Fluid (VOF) model and considering a free surface. And all The three cases were applied realizable k-epsilon model as the turbulence model. The results of calculations were verified for the suitability of calculations by comparing MOERI's EFD results.

• Journal of computational fluids engineering
• /
• v.20 no.2
• /
• pp.1-6
• /
• 2015

In this study, a numerical prediction on propulsive performance of a ducted propeller in open water condition was carried out by solving Reynolds averaged Navier-Stokes(RANS) equation using computational fluid dynamics(CFD). A configuration of propeller Ka-470 inside duct 19A was considered. Hexahedral grid system was generated by dividing whole computational domain into three separate regions; propeller, duct and outer flow region. A commercial CFD software, ANSYS-CFX was used for numerical simulations. Results were compared with experimental data and showed considerable improvement in accuracy, in comparison to those from surface panel method which is based on potential flow assumption. The results also exhibited the importance of grid system within the gap between the inner surface of duct and blade tip for accurate prediction of propulsive performance of ducted propeller.

• International Journal of Ocean System Engineering
• /
• v.3 no.2
• /
• pp.77-89
• /
• 2013

The propeller performance has been investigated using a benchmark Duisburg Test Case ship with RANSE. First, the hydrodynamic characteristics of propeller in case of open water have been analyzed by a commercial CFD program and the results are compared with those of experimental data. Later, the flow around the bare hull has been solved and the frictional resistance value and form factor of the ship have been obtained and compared with those of ITTC57 formulation and experimental results for validation. The free surface effect has been ignored. A good agreement has been obtained between the results of RANSE and experiments at both stages. Then the ship - propeller interaction problem was solved by RANSE and the differences in thrust, torque and efficiency of propeller as compared with the open-water numerical results have been discussed.

• Journal of the Society of Naval Architects of Korea
• /
• v.39 no.3
• /
• pp.8-17
• /
• 2002

In this paper, the computational analysis of open-water characteristics for three model propellers(P4119, P4842 and 3 podded propeller of KRISO) is done by using a viscous-flow method based on Reynolds-Averaged Navier-Stokes equations. The results are presented for open-water performances, blade-section pressures, and circumferentially-averaged velocity profiles for the all three propeller models. Overall close agreements with available experimental data are shown. However, some discrepancies are also found in the pressure near the leading edge of the propeller blade and the open-water performance of the podded propellers.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.1
• /
• pp.123-128
• /
• 2016

The effect of propeller surface roughness condition on ship performance is very significant even the influence of fouling on propeller performance is not well established compared to biofouling on the hull surface. In present study, predictions of open water efficiency of propeller are made for three different fouling conditions, and its application is given for the 7m full-scale propeller of a medium-size tanker in open water condition. The numerical predictions of propeller efficiency loss due to fouling are based on the results from laboratory-scale drag measurements and boundary layer similarity law analysis presented in Schultz (2007) together with an in-house unsteady lifting surface code which is an appropriate tool to predict the effect of propeller surface roughness on propeller performance. The results of this study indicate that the subject propeller with the small calcareous fouling ($k_s=0.001$) can lead to as high as 15 % loss at the propeller operating condition (J=0.5) and the loss of propeller efficiency due to fouling should be evaluated while the ship is operating.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.8 no.1
• /
• pp.22-37
• /
• 2016

This article investigates numerical modeling of surface piercing propeller (SPP) in unsteady open water condition using boundary element method. The home code based on BEM has been developed for the prediction of propeller performance, unsteady ventilation pattern and cross flow effect on partially submerged propellers. To achieve accurate results and correct behavior extraction of the ventilation zone, finely mesh has generated around the propeller and especially in the situation intersection of propeller with the free surface. Hydrodynamic coefficients and ventilation pattern on key blade of SPP are calculated in the different advance coefficients. The values obtained from this numerical simulation are plotted and the results are compared with experiments data and ventilation observations. The predicted ventilated open water performances of the SPP as well as ventilation pattern are in good agreement with experimental data. Finally, the results of the BEM code/experiment comparisons are discussed.