• Journal of the Korean Society of Propulsion Engineers
• /
• v.13 no.4
• /
• pp.1-8
• /
• 2009

Accumulated slag mass was predicted to estimate accurate performance of kick motor (KM) system. The validation of numerical analysis was performed with mass flow rate measured at the 4th ground test of the KM. The study described here includes the internal flow field of KM at various time steps during burning. Slag mass accumulation was analyzed through the aluminum oxide particle paths to predict slag mass deposition. Numerical analysis to solve both flow field and droplet accumulation was performed with Fluent 6.3 program. Analysing the effects of the acceleration, starting position and diameters of the aluminum oxide particles, total slag mass accumulation was obtained.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.3
• /
• pp.38-44
• /
• 2000

In general liquid rocket nozzles are protected from hot combustion gas by regenerative cooling techniques. But due to the complexity of the cooling system, it causes increase of system cost and frequently source of the system malfunction. Recently, instead of regenerative cooing, ablative material are used to protect combustion chamber wall and nozzle. To determine the nozzle material erosion rate and erosion shape, more than 500 hot fire test were performed by using 100 lb thrust experimental liquid rocket. Test variable were propellant feed sequence, injector, position of igniter and liquid oxygen supply temperature.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.213-217
• /
• 2017

Since more than 30% of the liquid rocket engine failures occur during the start-up process, and the Space Shuttle Main Engine (SSME) is especially sensitive to small changes in propellant conditions, a 2% error in the valve position or a 0.1sec timing error could lead to significant damage of the engine, simulation modeling of start-up process is important. However, there are many difficulties associated with engine start-up process caused by nonlinear mass flow and heat transfer characteristics associated with filling an unconditioned engine system with cryogenic propellants. In this paper, we modelled a SSME simulation model using partially Computational Fluid Dynamics (CFD) method to solve these problems and checked the performance by comparing with the performance of the simulation model using the lumped method under the state of normal condition.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.320-329
• /
• 2008

The influence of thermodynamic transition associated with transcritical nitrogen injection upon the flow structure was investigated to explore numerical simulation of the injectant dynamics of oxygen/hydrogen coaxial jet in liquid rocket engines. Single and coaxial nitrogen jets were treated by comparing the transcritical and perfect-gaseous conditions, wherein the numerical model was accommodative to the real-fluid thermodynamics and transport properties at supercritical pressures. The model was in the first place validated by comparing the results of transcritical nitrogen injection between calculations and available experiments. For a single jet under the transcritical condition, the nitrogen kept a relatively high density up to its pseudo-critical temperature inside the mixing layer, since it remains less expanding until heated up to its pseudo-critical temperature. Numerical analysis revealed that cryogenic jets exhibit strong dependence of specific enthalpy profile upon the associated density profile that are both dominated by turbulent thermal diffusion. In the numerical model, therefore, exact evaluation of turbulent heat fluxes becomes very important for simulating turbulent cryogenic jets under supercritical pressures. Concerning the coaxial jets due to transcritical/gaseous nitrogen injections, the density profile inside the mixing layer was again affected by the thermodynamic transition of nitrogen. However, hydrodynamic instability modes of the inner jet did not show significant differences by this thermodynamic transition, so that further study is needed for the mixing process downstream of the near injection position.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.3
• /
• pp.1-13
• /
• 2021

Effects of the nozzle wall angles on the supersonic flow field in a thrust optimized nozzle were numerically investigated. The combustor and operating condition of 30-tonf rocket engine was selected to study the optimum nozzle shape. The nozzle flow of combustion products was realized by the shifting equilibrium calculation for the propellant of kerosene-LOx. The change of nozzle wall angles induced different developing patterns of the internal and secondary shock wave. The optimum nozzle was obtained when the internal shock was in a specific position at the nozzle outlet. The nozzle wall angles of the optimum nozzle were very similar to those of the optimum nozzle which does not consider the shock wave.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.6
• /
• pp.979-985
• /
• 2011

This paper includes that there are results of designing the flash hider and analyzing fluid dynamics of a front area of the barrel to shorten the length of small arms. Generally, the muzzle flash can be generated out of the barrel by the reaction between the oxygen in the air and unburned gunpowder contained in the propellant gas if a barrel is not long enough to burn gunpowder fully inside of the barrel. Though, the hugh muzzle flash, which is a characteristic of small arms with short barrel length, caused a soldier to aim at the target at night by making the soldier blind for a while and endangers his life by revealing firing position to enemies. Besides, the heat of muzzle flash can weaken the performance of thermal sights, which are attached to small arms for night battlefield. In this paper, flash hiders with several different shapes were designed for a newly developed 5.56mm caliber rifle with short barrel length. The performance of each flash hider to reduce the muzzle flash was compared theoretically and experimentally. Through the authorized test procedure, a highly efficient design of flash hider for reducing the muzzle flash was identified. The result of the paper can be helpful when designing flash hiders for small arms with short barrel length.