• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.05a
• /
• pp.664-667
• /
• 2011

In this paper, threshold voltage characteristics have been analyzed as one of short channel effects occurred in double gate(DG)MOSFET to be next-generation devices. The Gaussian function to be nearly experimental distribution has been used as carrier distribution to solve Poisson's equation, and threshold voltage has been investigated according to projected range and standard projected deviation, variables of Gaussian function. The analytical potential distribution model has been derived from Poisson's equation, and threshold voltage has been obtained from this model. Since threshold voltage has been defined as gate voltage when surface potential is twice of Fermi potential, threshold voltage has been derived from analytical model of surface potential. Those results of this potential model are compared with those of numerical simulation to verify this model. As a result, since potential model presented in this paper is good agreement with numerical model, the threshold voltage characteristics have been considered according to the doping profile of DGMOSFET.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.22 no.1
• /
• pp.45-53
• /
• 1985

For the analysis of vertical vibrations of a ship's hull, the Timoshenko beam analogy is accepted up to seven or eight-node modes provided that the system parameters are properly calculated. As to the shear coefficient, it has been a common practice to apply the strain energy method or the projected area method. The theoretical objection to the former is that it ignores lateral contraction due to Poisson's ratio, and the latter is of extreme simplifications. Recently, Cowper's and Stephen's shear coefficient formulas have drawn ship vibration analysts' attentions because these formulas, derivation of which are based on an integrations of the equations of three-dimensional elasticity, take Poisson's ratio into account. Providing computer programs for calculation of the shear coefficient of ship sections modeled as thin-walked multicell sections by each of the forementioned methods, the authors calculated natural vibration characteristics of a bulk carrier and of a container ship by the transfer matrix method using shear coefficients obtained by each of the methods, and discussed the results in comparision. The major conclusions resulted from this investigation are as follows: (1) The shear coefficients taking account of the effects of Poisson's ratio, Cowper's $K_c$ and Stephen's $K_s$, result in higher values of about 10% in maximum as compared with the shear coefficient $K_o$ based on the conventional strain energy methods; (a) $K_c/K_o{\cong}1.05\;and\;K_s/K_o{\cong}1.10$ for ships having single skin side-shell such as a bulk carrier. (b) $K_c/K_o{\cong}1.02\;and\;K_s/K_o{\cong}1.05$ for ships having longitudinally through bulkheads and/or double side-shells in the portion of the cargo hod such as a container carrier. (2) The distributions of the effective shear area along the ship's hull based on each of $K_o,\;K_c\;and\;K_s$ are similar each another except the both end portions. (3) Natural frequencies and mode shapes of the hull based on each of $K_c\;and\;K_s$ are of small differences as compared each other. (4) In cases of using $K_c\;or\;K_s$ in ship vibration analysis, it is also desirable to have the bending rigidity be corrected according to the effective breadth concept. And then, natural frequencies and mode shapes calculated with the bending rigidity corrected in the above and with each of $K_o,\;K_c\;and\;K_s$ result in small differences as compared each another. (5) Referring to those mentioned in the above (3) and (4) and to the full-scale experimental results reported by Asmussen et al.[17], and considering laboursome to prepare the computer input data, the following suggestions can safely be made; (a) Use of $K_o$ in ship vibration analysis is appropriate in practical senses. (b) Use of $K_c$ is appropriate even for detailed vibration analysis of a ship's hull. (6) The effective shear area based on the projected area method is acceptable for the two-node mode.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.1
• /
• pp.47-52
• /
• 2015

In the slope stability analysis and design, Limit Equilibrium Method (LEM) and Shear Strength Reduction technique (SSR) are mainly used. Both methods are able to perform two and three dimensional analysis. SSR is considered to be more sensitive and more reasonable than LEM by many researchers. However, in practice LEM is still widely used because of the increase of analysis time and complexity of the model in SSR. In this study, three dimensional analysis of the protruding rock slope is performed by SSR in order to study the effects of protruding length using rock slope FLAC 3D. In this study, as results of analysis variations of the safety factor have been studied according to slope angle, slope height, the soil strength, protruding slope length projected variables. The results show that the factor of safety as more affected by the shapes of the protruding rock slope than the rock strength.

• Journal of the Korean housing association
• /
• v.23 no.5
• /
• pp.95-102
• /
• 2012

We studied in order to find out suitable amounts of board by visual effects to establish indoor boards and human psychological effects by several board designs. Thirty students of C university were tested in constant temperature/humidity room and interviewed after tests. The experimental visual images were projected from 54' TV. As a result, the board length that showed high preference and satisfaction was the 90cm both horizontal and vertical direction. We found that vertical board gave an impression of a linear and narrow shape and the horizontal board gave wide space and cool feeling from psychological analytical study. The factors affecting satisfaction in horizontal direction were refreshing, intimacy, beauty, area, splendor and those in vertical direction were a sense of security, beauty, texture, intimacy, continuity, extensity, natural feeling. We got 5 factors from the result of factor analysis in order to get psychological factor axis. Those were pleasantness, artificiality, openness, dynamics, refinement. By multiple regression analysis, the factor pleasantness had the highest impact on visual satisfaction on scenary. The study on psychological factor difference by analysis of variance showed that psychologically feeling amount about pleasantness, artificiality, dynamics, refinement, and openness had statistically meaningful difference despite of board direction. We found that the 90cm had a tendency as a changing point leading image change by the investigative analysis of board direction based on factor points.

• Structural Engineering and Mechanics
• /
• v.76 no.1
• /
• pp.1-15
• /
• 2020

The aim of this paper is to simply present live load factor calculation methodology formulation with the addition of a simple new future load projection procedure to previously proposed two methods. For this purpose, Oregon Weigh-in-Motion (WIM) data were used to calculate live load factors by using WIM data. These factors were calculated with two different approaches and by presenting new simple modifications in these methods. A very simple future load projection method is presented in this paper. Using four different WIM sites with different average daily truck traffic (ADTT) volume, and all year data, live load factors were obtained. The live load factors, were proposed as a function of ADTT. ADTT values of these sites correspond to three different levels which are approximately ADTT= 5,000, ADTT = 1,500 and ADTT ≤ 500 cases. WIM data for a full year were used from each site in the calibration procedure. Load effects were projected into the future for the different span lengths considering five-year evaluation period and seventy-five-years design life. The live load factor for ADTT=5,000, AASHTO HS20 loading case and five-year evaluation period was obtained as 1.8. In the second approach, the methodology established in the Manual for Bridge Evaluation (MBE) was used to calibrate the live load factors. It was obtained that the calculated live load factors were smaller than those in the MBE specifications, and smaller than those used in the initial calibration which did not convert to the gross vehicle weight (GVW) into truck type 3S2 defined by AASHTO equivalents.

• Korean Journal of Cognitive Science
• /
• v.18 no.3
• /
• pp.223-244
• /
• 2007

Two well known mis-localization effects, flash-lag effect (FLE) and the Pulfrich effect, have similar phenomena and theoretical explanations. In order to directly compare two phenomena, thereby examining the possibility that two phenomena have a common mechanism, the magnitudes of two effects were measured under the same experimental settings and stimuli. The Pulfrich depth was measured from each of four different brightness ratios of two moving stimuli, each of which was projected to each eye. The magnitude of FLE was measured from each of five different brightness levels, which were the same levels used in the Pulfrich experiment. The Pulfrich depth was increased with the increase of brightness ratio, whereas similar pattern was not found in the magnitude of FLE. Furthermore, actual Pulfrich depths were greatly different from those predicted from the difference of two FLEs. These results suggest that two phenomena may not have a common mechanism.

• Journal of the Society of Naval Architects of Korea
• /
• v.42 no.3
• /
• pp.259-267
• /
• 2005

The effects of hull flexibility on shaft alignment are growing as ship sizes are increased mainly for container carrier and LNG carrier. In order to consider hull flexibility on a propulsion shafting system, standardization of ship service conditions is necessary because hull deformation is continuously variable according to ship service conditions. How to summarize ship service conditions is suggested based on practically applicable four viewpoints : hull, engine, loading and sea status. Effects of the external forces acting on a ship propulsion shafting system are generally commented. Several design criteria regulated by classification societies are pointed at issue which seems to have Insufficient technical background. A qualitative verification is carried out to point out the invalidity of the assumption of effective supporting position. In this work, an elastic nonlinear multi-supporting bearing system is introduced as a key concept of the elastic shaft alignment. Hertz contact theory is proved to be more proper one than projected area method in calculation of the nonlinear elastic stiffness of the bearing, The squeezing and oil film pressure calculations in the long journal bearing like an after stern tube bearing are recognized as a necessary process for elastic shaft alignment design.

• Publications of The Korean Astronomical Society
• /
• v.30 no.2
• /
• pp.397-399
• /
• 2015

Recently, cosmic voids have been recognized as a powerful cosmological probe. A number of studies have focused on the effects of the gravitational lensing by voids on the temperature (and in some cases polarization) anisotropy of the Cosmic Microwave Background (CMB) background at relatively large to medium scales, l ~ 1000. Many of these studies attempt to explain the unusually large cold spot in CMB temperature maps and dynamical evidence of dark energy via detections of late-time integrated Sachs Wolfe (ISW) effect. Here, the effects of lensing by voids on the CMB temperature anisotropy at small scales, up to l = 3000, will be investigated. This work is carried out in the light of the benefits of adding large catalogues of cosmic voids, to be identified by future large galaxy surveys such as EUCLID and LSST, to the analysis of CMB data such as those from Planck mission. Our numerical simulation utilizes two methods, namely, the small-de ectionangle approximation and full ray-tracing analysis. Using the fitted void density profiles and radius (RV ) distribution available in the literature from N-body simulations, we simulated the secondary temperature anisotropy (lensing) of CMB photons induced by voids along a line of sight from redshift 0 to 2. Each line of sight contains approximately 1000 voids of effective radius $RV_{,eff}=35h^{-1}Mpc$ with randomly distributed radial and projected positions. Both methods are used to generate temperature maps. The two methods will be compared for their accuracy and effciency in the implementation of theoretical modeling.

• Journal of Climate Change Research
• /
• v.8 no.3
• /
• pp.213-220
• /
• 2017

The purpose of this study is to analyze effects of Greenhouse Gas (GHG) emission reduction in district energy business mainly based on Combined Heat and Power (CHP) plants. Firstly this paper compares the actual carbon intensity of power production between conventional power plants and district energy plants. To allocate the GHG from CHP plants, two of different methods which were Alternative Generation Method and Power Bonus Method, have been investigated. The carbon intensity of power production in district energy plants ($0.43tonCO_2e/MWh$) was relatively lower than conventional gas-fired power plants ($0.52tonCO_2e/MWh$). Secondly we assessed the cost effectiveness of reduction by district energy sector compared to the other means using TIMES model method. We find that GHG marginal abatement cost of 'expand CHP' scenario (-$134/ton$CO_2$) is even below than renewable energy scenario such as photovoltaic power generation ($87/ton$CO_2$). Finally the GHG emission reduction potential was reviewed on the projected GHG emission emitted when the same amount of energy produced in combination of conventional power plants and individual boilers as substitution of district energy. It showed there were 10.1~41.8% of GHG emission reduction potential in district energy compared to the combination of conventional power plants and individual boilers.

• Economic Analysis
• /
• v.27 no.1
• /
• pp.37-66
• /
• 2021

This paper examines the potential impacts of COVID-19 on poverty in ASEAN countries. The first estimate, adopted from Summer et al. (2020) and Nonvide (2020), configures three scenarios of contractions in per capita household income or consumption; the impact of each scenario on poverty is calculated using poverty lines at different thresholds. In the second estimate, poverty impacts in 2020 and 2021 were projected using regression models controlling for unobserved country effects, unbalanced data, and endogeneity. COVID-19 has been shown to have negative impacts on poverty reduction in the ASEAN Member States. To reduce poverty, concerted efforts are needed to implement policies for reducing income inequality and promoting economic growth. Such efforts will not only speed up the countries' return to pre-pandemic poverty levels but also contribute to further accelerating poverty reduction.