• 접착 및 계면
• /
• 제4권2호
• /
• pp.21-29
• /
• 2003

Hot AC anodising has been evaluated us pre-treatment for aluminium prior to structural adhesive bonding. Phosphoric and sulphuric acid hot AC anodising showed very promising adhesion promoter capabilities with durability comparable with the best standard DC anodising procedures. AC anodising does not required etching prior to anodising and offers u pre-treatment time down to 20 seconds. The interface/interphase between the aluminium substrate and the adhesive was investigated in order to get a better understanding of the involved adhesion mechanisms and to explain the long-tenn properties. The alkaline medium formed at the oxide layer/adhesive interface has been shown to induce a partial dissolution of the oxide layer leading to the formation of metallic ions which diffuse in the adhesive (EPMA measurements). The effect of diffusion of the Al ions on adhesion and joint durability is still uncertain but studies showed that pre-bond moisture affected the joints durability and to some extent the diffusion length. specially for DC anodised samples. So far no direct correlation could be established between the diffusion length d and the joints durability but new trials with better control over the elapsed time between bonding and adhesive curing are expected to help getting a better understanding of the involved mechanisms.

• Journal of Korean Neurosurgical Society
• /
• 제50권5호
• /
• pp.403-408
• /
• 2011

Objective : Contrary to some clinical belief, there were quite a few studies regarding animal models of intracerebral hemorrhage (ICH) $in$ $vivo$ suggesting that prior use of statins may improve outcome after ICH. This study reports the effect of 3-hydroxy-3-methyl-glutaryl-coenzyme A (HMG CoA) reductase inhibitor, simvastatin given before experimental ICH. Methods : Fifty-one rats were subjected to collagenase-induced ICH, subdivided in 3 groups according to simvastatin treatment modality, and behavioral tests were done. Hematoma volume, brain water content and hemispheric atrophy were analyzed. Immunohistochemical staining for microglia (OX-42) and endothelial nitric oxide synthase (eNOS) was performed and caspase-3 activity was also measured. Results : Pre-simvastatin therapy decreased inflammatory reaction and perihematomal cell death, but resulted in no significant reduction of brain edema and no eNOS expression in the perihematomal region. Finally, prior use of simvastatin showed less significant improvement of neurological outcome after experimental ICH when compared to post-simvastatin therapy. Conclusion : The present study suggests that statins therapy after ICH improves neurological outcome, but prior use of statins before ICH might provide only histological improvement, providing no significant impact on neurological outcome against ICH.

• 동의생리병리학회지
• /
• 제22권6호
• /
• pp.1537-1543
• /
• 2008

The purpose of this study was investigation to examine the prevention diabetic mellitus and treatment effect on Gastrodia Elata Blume(GEB) dieted at prior and after induced diabetic application. Prior induced diabetic 3 weeks ago application GEB dieted. It is to analysis changes in body weight, blood glucose, SOD, CAT and histopathological findings. For the fingding significantly concentration diabetic rats were divided into 3 different experimental groups and each groups were induced diabetic. Experimental group Ⅰ (STZ-induced diabetic rats; n=10), experimental group Ⅱ (after induced DM and GEB dieted rats; n=10), experimental group Ⅲ (Prior GEB dieted thereafter DM induced; n=10). Prior and After GEB dieted application was that body weight, blood glucose were increase in experimental group Ⅱ, Ⅲ. Specially, group Ⅲ was significantly change than group Ⅱ at 1st weeks. and the level of CAT were significantly decrease in experimental group Ⅱ, Ⅲ than group Ⅰ. but SOD level was increase in experimental group Ⅱ, Ⅲ than group Ⅰ. In histological observation; group Ⅰ showed decrease in the intensity and incidence of vacuolations, cellular infiltration and hypertrophy of in liver and kidney. The Gomori's stain result, group Ⅰ showed disruption ${\beta}$-cell in pancrease.

• Asian Pacific Journal of Cancer Prevention
• /
• 제15권5호
• /
• pp.2095-2100
• /
• 2014

Objective: Most patients with advanced breast cancer experience resistance to endocrine treatment and eventual disease progression. This meta-analysis was designed to compare the efficacy and tolerability of fulvestrant 250mg with anastrozole 1mg in postmenopausal women with advanced breast cancer. Methods: Electronic literature databases (Cochrane Library, Medline, and Embase) were searched for randomized controlled trials (RCTs) published prior to August 2013. Only RCTs that compared fulvestrant 250mg to anastrozole 1mg in postmenopausal women with advanced breast cancer were selected. The main outcomes were time to treatment failure (TTF), time to progression (TTP), duration of response (DOR), clinical benefit rate, and tolerability. Results: Four RCTs covering 1,226 patients (fulvestrant, n=621; anastrozole, n=605) were included in the meta-analysis. Fulvestrant increased the DOR compared to anastrozole (HR =1.31, 95% confidence interval [CI] 1.13-1.51). There was no statistically significant difference between fulvestrant and anastrozole in terms of TTF (HR=1.02, 95%CI 0.89-1.17), complete response (RR=1.79, 95%CI, 0.93-3.43), and partial response (RR=0.91, 95%CI 0.69-1.21). As for safety, there was no statistical significance between the two groups for common adverse events. Conclusion: Fulvestrant 250mg is as effective and well-tolerated as anastrozole 1mg treatment for advanced breast cancer in postmenopausal women whose disease progressed after prior endocrine treatment. Thus, fulvestrant may serve as a reasonable alternative to anastrozole when resistance is experienced in breast cancer cases.

• Asian-Australasian Journal of Animal Sciences
• /
• 제4권2호
• /
• pp.131-136
• /
• 1991

Four male swamp buffaloes weighing $460.5{\pm}44.6kg$ were used to study the effects of different cooling techniques on draught capacity. Each animal carted an 882 kg load on the same asphalt road for one hour during four different time periods: 9:00-10:00 A.M., 10:30-11:30 A.M., 2:00-3:00 P.M. and 3:30-4:30 P.M. Simultaneously, all animals were subjected to five different treatments on five days of similar environmental conditions. In Treatment 1, animals were put stationary in a field and did no work; in Treatment 2, animals were worked without any cooling method; in Treatment 3, fifteen-minute wallow was allowed to animals prior to working; in Treatment 4, animals were covered with wetted jute bags while working, and in Treatment 5, two buckets of water were poured over the buffaloes' trunks just prior to working. The experiment was conducted from April to July 1989, when the weather was very hot. It was found that cooling methods and working times did not affect the draught efficiency of buffaloes during the one hour, but did affect physiological traits. The work load had a larger partial effect on physiological responses of buffalo other than respiration rate than did climatic variables except on the respiration rate of the buffaloes. One cooling technique that seemed to slow the increase of body temperature while working was covering the buffalo's back with wetted jute bags. Animals working at different times had significant differences in the increase of physiological traits except pulse rate.

• 열처리공학회지
• /
• 제16권5호
• /
• pp.267-274
• /
• 2003

The effect of the thermo-mechanical treatment on the microstructural development and the electric conductivity of Cu-Ca alloys are studied for the thixoforming processed rotor of the induction motor The Cu-Ca alloys containing Ca less than 1.0wt% show the electrical conductivity higher than 80% IACS They also show broad melting range over $150^{\circ}C$ which is desirable for the thixoforming process The semi-solid microstructure of cast alloy changes from the dendrite structure to globular structure by prior deformation before reheating. The details of microstructural changes by the thermo-mechanical treatment are discussed.

• 한국염색가공학회지
• /
• 제13권1호
• /
• pp.32-37
• /
• 2001

Silk fabric was sputter-treated with Au, Cu, SUS, and Ti using poly(vinyl alcohol) (PVA) as a binder, and its changes in color, antielectrostatic property, airpermearbility, and rubbing fastness were investigated. Sputter-treated silk fabric had a natural color of metal target, which was deepened by treatment of PVA solution. The rubbing fastness of thin metal layer formed by sputtering was improved by PVA treatment. Au had highest rubbing fastness among the metal targets. In addition, PVA treatment posterior to sputtering resulted In higher rubbing fastness than the other treatment method. However, a reverse trend was found in antielectrostatic property. Air permeability of the sputter-treated silk fabric was improved by PVA treatment, which was highest when sputtering was conducted prior to PVA treatment.

• 한국염색가공학회지
• /
• 제9권6호
• /
• pp.87-95
• /
• 1997

Wool samples were treated by potassium tert-Butoxide(t-BuOK) in anhydrous tert-butanol to remove the bound surface lipid-layer, and the weight loss behaviors in protease solution and dyeabilities of the samples were studies. The C/N ratio of the surface of the t-BuOK-treated wool was shown to be 4.3 from XPS analysis. From SEM pictures any remarkable change in the shape of surface curticle during the proteasw treatment was not observed regardless of prior t-BuOK treatment. Dyeing rate and equilibrium adsorption of Orange II, a typical levelling type acid dye, on wool were not changed by protease or t-BuOK treatment, but those of Milling Cyanine 5R, a typical milling type acid dye, on wool were greatly enhanced by t-BuOK treatment in spite that, from alkali and urea-bisulfite solubilities, no damage on the inner part of wool fiber was expected by t-BuOK treatment.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.332-333
• /
• 2007

The effect of asymmetric rolling on the recrystallization texture of an AA 3003 Aluminum alloy was investigated by X-ray diffraction. It was found that the texture of asymmetrically rolled sheets prior to subsequent heat treatment promoted the formation of the <111>//ND textures, and remained after heat treatment at $275^{\circ}C$ during 20 min in salt bath condition.

• 산업기술연구
• /
• 제1권
• /
• pp.53-60
• /
• 1981

A study has been performed on the effect of TMT(thermomechanical treatment) on the mechanical properties of steel and aluminum alloys. Improvement of the mechanical properties on steel by HTMT is due to refinement of prior austenite grain size, martensite lath size and the distribution of fine carbide precipitates and on aluminum alloy by ITMT is due to grain size refinement, homogeneous distribution of small second phase particles and retardation of the recrystallization.