• 한국표면공학회지
• /
• 제33권2호
• /
• pp.107-114
• /
• 2000

In this study, we investigated the possibility of the application of the EzROBO system to direct shaping techniques which can make arbitrary shapes without any specific mold. We formed arbitrary shapes using raw materials of EH-260D (Epoxy＋Binder) with the conditions of $250\mu\textrm{m}$ layer thickness, 0.2MPa working pressure, 20mm/sec working velocity, and 1.8mm needle thickness. The developed Spatial Printing Technique showed enhanced working velocity and lower cost than existing 3DP process, and is expected to replace the existing process through the process optimization in the future.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 1999년도 제1회 학술대회논문집(KIASC 1st conference 99)
• /
• pp.22-25
• /
• 1999

A well oriented Bi-2212 superconductor thick films were fabricated by screen printing with a Cu-free Bi-Sr-Ca-Cu-O powder on a copper plate and heat-treating at 820- $880^{\circ}C$for several minute in low oxygen pressure or are. At minute in low oxygen pressure of air. At , the printing layer partially melted by reaction between the Cu-free precursor by reaction between the Cu-free$870^{\circ}C$ precursor and CuO of the oxidizing copper plate. It is believed that the solid phase is Bi : Sr : Ca : Cu = 2 : 2 : 0 : 1. It is likely that the Bi-2212 superconducting phase is formed at Bi-2212 superconducting phase is formed at Bi-free phase/liquid interface by nucleation and grows.

• 마이크로전자및패키징학회지
• /
• 제16권3호
• /
• pp.53-59
• /
• 2009

PCB 표면 개질 및 세정에 있어서 저압 수은 램프를 이용한 UV 장비가 널리 사용되어왔다. 본 연구에서는 공정의 생산성을 향상 시키기 위하여 기존 UV 장비를 대체하여 리모트 DBD 방식의 대기압플라즈마 장비를 새로이 개발하였다. 두 장비의 생산성 비교는 처리 시간 증가에 따른 표면 접촉각의 변화를 측정함으로써 정량적으로 비교할 수 있었다. 측정 결과 대기압 플라즈마 장비의 생산성이 UV 장비에 비하여 매우 우수한 것으로 확인 되었다. 또한 XPS를 이용한 표면 조성 측정 결과 동일한 접촉각 수준에서 UV 및 대기압 처리의 효과는 유사한 것으로 파악되었다. 즉, 유기 오염 수준이 감소되었으며 표면 일부 표면 원소가 산회되었다. 최종적으로 대기압 플라즈마를 BGA제조의 플럭스 도포 공정에 적용하였는데, 대기압 플라즈마를 처리함으로써 도포 공정의 균일도가 향상되는 결과를 얻을 수 있었다.

• 대한기계학회논문집B
• /
• 제38권8호
• /
• pp.709-714
• /
• 2014

리버스 옵셋 인쇄는 인쇄전자를 위한 미세 패터닝기술 중 하나로서 수 ${\mu}m$ 이하의 선폭을 구현할 수 있다. 옵셋 인쇄의 특성상 잉크는 PDMS 재질의 블랑켓에 전사된 후 음각으로 패턴된 클리쉐에 접촉하여 불필요한 패턴을 제거하게 되는데, 이 때 블랑켓은 압력에 의하여 음각 패턴 내부로 침투하는 변형이 발생한다. 이러한 변형은 인쇄 압력에 비례하며, 과도한 인쇄 압력은 넓은 면적의 패턴을 인쇄할 때 클리쉐 패턴의 바닥에 블랑켓이 닿는 불량을 일으키게 된다. 이 논문에서는 리버스 옵셋 인쇄에서 가압변위에 따른 PDMS 블랑켓의 변형을 유한요소기법을 이용하여 모델링하고 접촉압력 대비 변형량을 예측함으로써 실제 인쇄 장비의 실험 결과와 비교하여 인쇄결함이 발생하지 않도록 하는 클리쉐의 제작조건을 제시하고자 한다.

• 펄프종이기술
• /
• 제39권2호
• /
• pp.31-37
• /
• 2007

Lithography like off-set printing is processed using the repellent properties between water and oil, so all inks for off-printing must work with dampening solution(water). The dampening water may cause the emulsification of ink by the printing pressure in the printing nip. This study aimed to investigate the effect of emulsified inks on print mottle. The cyan ink was emulsified artificially with the different IPA(isopropyl alcohol) content in this study. We evaluated the print mottle by densitometer and image analysis method. The print mottle phenomenon was directly affected by IPA content. The emulsification of inks also had an influence on flow properties of inks and it increased ink transfer rate. It, however, caused low ink density. Moreover the emulsified inks were spreaded to around dots and cause the thinning density on the non-printing area like print mottle. The trial printing showed that the emulsified inks also cause scumming on the printing result with little mistake of adjusting dampening solution and mostly decreasing dot reproduction. We could, therefore, find out the obvious effect of emulsified inks on print mottle.

• 한국인쇄학회지
• /
• 제26권2호
• /
• pp.1-13
• /
• 2008

Printed mottle of coated paper is one of the most common phenomenon and the most difficult problem in offset printing. Offset printing is processed mainly processed by the attractive properties between water and oil, so all inks for off-printing must work with dampening solution(water). It may cause the emulsion on the printing nip from the printing pressure. This study aimed to investigate the effect of emulsified inks on print mottle from emulsified cyan ink by force with each different IP A contents. We measured the print mottle by densitometer and image analysis method. The emulsified inks also give effect to now properties of inks and it caused more ink transfer rate, however, it caused low density of inks. Moreover the emulsified inks were spreaded to around of dots and cause the thinning density on the non-printing area like print mottle. The results showed that the emulsified inks also cause scumming on the printing result with little mistake of adjusting dampening solution and mostly decreasing dot reproduction. So we could find out the obvious effect of emulsified inks to print mottle.

• 한국인쇄학회지
• /
• 제28권1호
• /
• pp.1-13
• /
• 2010

Gravure printing and manufacturing of advanced electronic components in a way that is going extra hold position. It is to print the electronic components of the rapid productivity improvements as well as cost-saving and environment-friendly industries such as the transition is a big advantage. However the mechanism of gravure is difficult to study scientifically because of high speed and excessively small size of the cell. To approach the mechanism we experimented using gravure printability. The condition of variables of IGT is pressure and velocity. By using Flow-3D simulation software, we built up the theoretical model under the constant variables. Then, we compared the real test with the simulation results. Therefore, it is studied the mechanism of gravure scientifically and it can be analysed the effect of the variable conditions.

• 한국인쇄학회:학술대회논문집
• /
• 한국인쇄학회 2001년도 국제학술발표회
• /
• pp.135-140
• /
• 2001

Laboratory test method which determines the emulsification rate of dampening solution and ink has been described In lithography using the mutual repellence of oil and water, the emulsification is produced by dispersion of dampening water and ink because of the printing pressure on a practical press. Rheological properties of Ink-Water balance are the important factors in lithographic printing. The emulsification theory and laboratory test method deduced from Surland and Kim. It is shown that the emulfisication curves relate to the rates of change in the emulsifide ink\`s flow properties, to the shear stability of the emulsion formed To study on the factors determining the emulsion velocity, we have measured water pickup and calculated emulsification velocity constant \`k\` and activation energy.

• 전기학회논문지P
• /
• 제65권2호
• /
• pp.142-150
• /
• 2016

This paper developed new manufacture process technology of slim type flexible flat lighting product used lower power white LED. Flexible flat lighting is applied to letter sign lighting, traffic lighting, interior wall lighting, flat lighting, aquarium back lighting, wreath light etc. Main manufacture process technology were developed drawing software for electronics circuit, inkjet electronic circuit pattern and inkjet white ink coating. For pattern printing it was utilized for piezoelectonic inkjet head printing technology. Also high vacuum pressure laminating technology was waterproofing for LED flat lighting protection. Hence, form process technology we were manufactured for flexible flat lighting product of the power 12 W, input voltage 48 V and plane size $480{\times}480mm$. It acquired a these validity from experiment results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1450-1451
• /
• 2008

To investigate the reliability of the conductive lines patterned by ink-jet printing, we evaluated the reliability of the ink-jet printed silver (Ag) patterns according to the guide lines built up as assessments methods in the production of conventional rigid printed circuit boards. The assessment methods include the uniformity of line width and space, adhesive strength, dielectric withstand, solder float, thermal shock test and pressure cooker test (PCT). To prepare assesment vehicles, different regular test patterns were created by Ag ink-jet printing on the same polyimide substrate for each of assessment methods.