• Korean Journal of Applied Biomechanics
• /
• v.28 no.4
• /
• pp.237-244
• /
• 2018

Objective: Flat-footed people struggle with excessive ankle joint motion during walking and running. This study aimed to investigate the effects of customized three-dimensional 3D-printed insoles on the kinematics of flat-footed people during daily activities (walking and running). Method: Fifteen subjects (height, $169.20{\pm}2.61cm$; age, $22.87{\pm}8.48years$; navicular bone height, $13.2{\pm}1.00mm$) diagnosed with flat feet in a physical examination participated in this study. Results: The customized 3D-printed insoles did not significantly affect 3D ankle joint angles under walking and running conditions. However, they shifted the trajectory of the center of pressure (COP) laterally during fast walking, which enhanced the load distribution on the foot during the stance phase. Conclusion: The customized 3D-printed insoles somewhat positively affected the pressure distribution of flat-footed people by changing the COP trajectory. Further research including comparisons with customized commercial insoles is needed.

• Design & Manufacturing
• /
• v.13 no.2
• /
• pp.17-21
• /
• 2019

In this study, selective laser sintered 3D printing mold core and metal core were used to investigate the difference of the thickness shrinkage from the gate of the injection molded part at a constant interval. SLS 3D printing mold core was made of nylon-based PA2200 powder and the metal core was manufactured by conventional machining method. As the PA2200 powder material has low strength, thermal conductivity and high specific heat characteristics compared with metal, molding conditions were set with the consideration of molten temperature and injection pressure. Crystalline resin(PP) and amorphous resin(PS) with low melting temperature and viscosity were selected for the injection molding experiment. Cooling time for processing condition was selected by checking the temperature change of the cores with a cavity temperature sensor. The cooling time of the 3D printing core was required a longer time than that of the metal core. The thickness shrinkage of the molded part compared to the core depth was measured from the gate by a constant interval. It was shown that the thickness shrinkage of the 3D printing core was 2.02 ~ 4.34% larger than that of metal core. In additions, in the case of metal core, thickness shrinkage was increased with distance from the gate, on the contrary, in the case of polymer core showed reversed aspect.

• Journal of the Korean Society of Radiology
• /
• v.13 no.7
• /
• pp.947-953
• /
• 2019

The purpose of this study was to manufacture a wrist brace using a computerized tomography system, clinical design software (MediACE 3D Program), and 3D printer. After acquiring the Dicom file of the upper limb with a computed tomography, the wrist brace was designed using the MediACE 3D Program to create a "stereolithography" file. The designed wrist brace was printed using a 3D printer. To verify the effectiveness of wrist assistive device manufactured by 3D printing technology, the stress distribution of the pressure and orthosis applied to bone and skin is represented by finite element analysis. It is expected that the wrist brace can be manufactured by reinforcing the part where the damage caused by pressure and breakage of the brace frequently occurs with the result of finite element analysis when producing the wrist brace.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.8
• /
• pp.675-685
• /
• 2016

A research area on liquid rocket engine has been suggested. Downsizing through combustion pressure rise and low price are major issues to gas generator cycle engines. A very high pressure turbopump and material against oxidizer rich environment may be necessary technologies for staged combustion cycle engines. Integrated analysis saving computing time is the trend of rocket engine systems analysis area. Other important research topics are the methane engine for reusable booster to reduce the cost, 3D printing and materials for high temperature or oxidizer rich environment.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.34 no.5
• /
• pp.39-48
• /
• 2002

The water retention of coating colors can be accurately measured by devices such as an AA-GWR water retention meter whose principle of measurement Is based on pressure filtration of coatings under an externally applied air pressure over a certain period of time. It was hypothesized that such devices could be also used to determine the immobilization solids (IMS) of coating colors by determining a sudden drop in the rate of dewatering, that is, a sudden change in the drainage curves. To test this hypothesis, the immobilization solids of coating colors containing various thickeners and water retention additives at different levels were first accurately measured by a modified immobilization tester based on the well-known gloss drop method, and then their values were compared with those obtained by an AA-GWR water retention tester. They agreed very well and showed that the standard deviation is only 0.14% in the IMS points between both methods. This good agreement was not surprising because both test methods are based on the same end-point, that is, the immobilization solids point at which menisci begin to form at the coating surface. Theoretical considerations supporting this new method for measuring the immobilization solids of coating colors are presented and some recommendations for the test method are discussed. Also, the effect of various thickeners and water retention additives on the properties and printability of coated papers is discussed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.366-366
• /
• 2012

현재 사용되고 있는 투명전극재료 중에 ITO(Indium Tin Oxide)가 가장 투명하면서 전기도 잘 통하고 생산성도 좋다. 투명전극은 비저항이 $1{\times}10^{-3}{\Omega}/cm$이하, 면 저항이 $10^3{\Omega}/sq$이하로 전기전도성이 우수하고 380에서 780 nm의 가시광선 영역에서의 투과율이 80%이상이라는 두 가지 성질을 만족시키는 박막이다. 본 연구에서 X-ray Film을 제작하기 위하여 상용화된 ITO Glass 전극 기판에 X-ray가 조사되면 직접 전자 전공 쌍(electron-hole pair)을 발생시켜 전기적 신호를 발생하는 광도전체 물질(Photoconductor)인 PbO, $PbI_2$, $HgI_2$를 스크린 프린팅(Screen Printing)법을 이용하여 각각 제작하였다. 상부 전극으로 마그네틱 스퍼터링(Magnetic Sputtering) 진공 증착 장치를 사용하여 전류, 전압, 아르곤 및 산소 유입량등을 조절하면서 상부 전극을 증착하였다. 이때 타켓으로 $In_2O_3;SnO_2$ (조성비:90:10wt%)를 사용 하였고, base pressure는 $9{\times}10^{-7}torr$, deposition pressure는 $3{\times}10^5torr$를 고정하였다. 또한 전류와 전압은 각각 0.4A, 800V로 유지하고, $O_2$:0.3 ppm, Ar의 경우 4.9 ppm에서 70 ppm까지 올려 플라즈마를 활성화 시킨 후 90초 동안 ITO를 증착하였다. 본 실험에 제작된 박막으로 X-ray을 조사하여 검출기로써 특성 평가를 실시하였으며, 실험결과 X-선 투과와 전도성 등 두가지 특성이 동시에 만족 될 만한 성능을 가질 수 있음을 확인 할 수 있었다.

• Journal of the Korean Ceramic Society
• /
• v.41 no.1
• /
• pp.30-35
• /
• 2004

PMW-PZT thick films of about $30{\mu}m$ thickness were fabricated on Pt/$TiO_2$/$SiN_x$Si substrate by the hybrid method of screen printing and PZT sol application. With the increase of the number of the sol application times, the sintered density and electrical properties of PMW-PZT thick films were evidently increased. For the PMW-PZT thick film with PZT sol application of 10-times, the dielectric constant ($\varepsilon_r$) was 745 at the frequency of 100 KHz and thepiezoelectric coefficient ($d_33$) was 155 pC/N at the applied pressure of 1 atm.

• Journal of the Korean institute of surface engineering
• /
• v.40 no.4
• /
• pp.190-196
• /
• 2007

Dye sensitized solar cells(DSSC) are the most promising future energy resource due to their high energy efficiency, low production cost, and simple manufacturing process. But one problem in DSSC is short life time compared to silicon solar cells. This problem occurred from photocatalytic degradation of dye material by nanometer sized $TiO_2$ particles. To prevent dye degradation as well as to increase its life time, the transparent coating film is needed for UV blocking. In this study, we synthesized nanometer sized $TiO_2$ particles in sols by increasing its internal pressure up to 200 bar in autoclave at $120^{\circ}C$ for 10 hrs. The synthesized $TiO_2$ sols were all formed with brookite phase and their particle size was several nm to 30 nm. Synthesized $TiO_2$ sols were coated on the backside of fluorine doped tin oxide(FTO) glass by ink jet printing method. With increasing coating thickness by repeated ink jet coating, the absorbance of UV region (under 400 nm) also increases reasonably. Decomposition test of titania powders dispersed in 0.1 mM amaranth solution covered with $TiO_2$ coating glass shows more stable dye properties under UV irradiation, compared to that with as-received FTO glass.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.6
• /
• pp.583-588
• /
• 2015

Flexible tactile sensors can provide valuable feedback to intelligent robots regarding the environment around them. This is especially important when robots such as, service robots share a workspace with humans. This paper presents a contact force measurement algorithm of a flexible tactile sensor. This sensor is manufactured by a direct-writing technique, which is one 3D printing method, using multi-walled carbon nano-tubes. An analog signal processing circuit has been designed and implemented to reduce noise contained in the sensor output. In addition, a digital version of the Butterworth filter was implemented by software running on a microcontroller. Through various experiments, characteristics of the sensor system have been identified. Based on three traits, an algorithm to detect the contact and measure the contact force has been developed. The entire system showed a promising prospect to detect the contact over a large and curved area.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.14 no.3
• /
• pp.1-10
• /
• 2012

This study has purpose to understanding recent trends and image effect of textile in fashion by looking to dyeing technique and aesthetics of diffusing image pattern. Further the study will hope to provide basic data for fashion and textile designer fashion. The methods of this study are academic literatures as well as practical study through case studies about actual works. Dyeing techniques and aesthetics of diffusing image pattern since 2000 fashion collection and their results are as follows. First, Dyeing techniques of diffusing image pattern are wet-dyeing and printing. There are plangi dyeing, salt dyeing, alcohol dyeing and ikat dyeing in the wet-dyeing and spray dyeing, discharge dyeing in the printing. There are tie-dyeing, rumpling-dyeing and plank-dyeing in the plangi. Second, Forming of the diffusing image pattern are due to uneven seeping and the contingency of a chemical reaction by reducing the pressure and intensity. Third, Aesthetics of diffusing image pattern are extracted purity missing childhood, fantasy escaping facts of the situation and abstraction representing informal world from formative characteristics of diffusing image pattern.