• Journal of the Korean Society of Clothing and Textiles
• /
• v.45 no.1
• /
• pp.155-167
• /
• 2021

The latest innovation in the field of fashion comes in the form of 3D-printed clothing. This study explores the composition and characteristics of the shapes in the architecture of Zaha Hadid, a representative architectural designer who expresses space in three dimensions. Hadid applies his aesthetic to fashion design using these distinctive geometric shapes to create design motifs as well as develop new clothing material with 3D printing technology. The research was conducted as follows. First, the lines and arrangement of the geometric shapes in Zaha Hadid's architecture were analyzed so that his design principles could be used as a theoretical basis for this study. The study also reviewed geometric fashion designs using 3D printing technology over the last ten years. Second, we developed triangular modules with rods and tongs that could be fashioned into clothing using fused deposition modeling (FDM) 3D printers. Lastly, the 3D printing fashion design was developed to explore new silhouettes, textures, and a novel way of producing clothing. This study hopes to serve as a stepping-stone for further research on innovations that combine fashion with technology.

• Journal of the Korean Orthopaedic Association
• /
• v.56 no.2
• /
• pp.103-116
• /
• 2021

The use of 3-dimensional (3D) printing is becoming more common, and its use is increasing in the orthopedic surgery. Currently, there are four major methods of using 3D printing technology in orthopedic surgery. First, surgical planning simulation using 3D printing model; second, patient-specific surgical instruments; third, production of customized prosthesis using 3D printing technique; fourth, patient-specific prosthesis produced by 3D printing. The areas of orthopedic surgery where 3D printing technology can be used are shoulder joint, spine, hip and pelvis, knee joints, ankle joint, and tumors. Since the diseases and characteristics handled by each area are different, the method of using 3D printing technology is also slightly different in each area. However, using 3D printing technology in all areas can increase the efficiency of surgery, shorten the surgery time, and reduce radiation exposure intraoperatively. 3D printing technology can be of great help in treating patients with particularly complex and difficult orthopedic diseases or fractures. Therefore, the orthopedic surgeon should make the most of the benefits of the 3D printing technology so that patient can be treated effectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.11
• /
• pp.802-809
• /
• 2017

3D printing technology is a manufacturing process for products, in which polymer and metal materials are laminated to form structures. It is advantageous for manufacturing parts requiring a high degree of design freedom and functionality. In addition, it would be a suitable technology for the production of parts for railway vehicles in the future, due to the need to produce parts in small quantities. In order to fully exploit the advantages of 3D printing technology, it is necessary to consider the process characteristics during the design of the product. In this study, the redesign and manufacturing technology of the product considering the performance and process conditions were studied for the heat exchanger in the air compressor of railway vehicles, as a trial application of the 3D printing technique. First of all, the design concept to improve the performance of the heat exchanger was defined, and the design range was specified to satisfy the performance of the present heat exchanger analyzed experimentally. Then, the detailed design was revised considering the characteristics of the metal 3D printing process, such as the manufacturing restrictions and production time. Based on the final design, the product was fabricated by the 3D printing process using aluminum material, and it was confirmed that the dimensional accuracy was satisfied. The weight of the final product was reduced by 41% compared with the existing products. The results of this study will make it possible to develop an efficient product design process for 3D printing technology.

• Korean Journal of Food Science and Technology
• /
• v.53 no.1
• /
• pp.29-33
• /
• 2021

The fish cake industry is attempting to overcome the standstill by adopting new production technologies, such as 3D printing technology. The characteristics of food 3D printing ink, including viscosity, hardness, and adhesiveness, are essential in food 3D printing technology. Therefore, in this study, the effect of salt on the gelation of surimi 3D ink and its texture for 3D printing were examined. After adding salt (1-4%) to fish meat, the viscosity and adhesiveness of fish meat was found to be increased by gelation. Among the fish surimi with various salt contents, surimi with 3% salt showed the most suitable characteristics, including viscosity, adhesiveness, and hardness, for a whirlwind and λ 3D printing model. Scanning electron microscopy showed that the addition of 3% salt resulted in the most adhesive surimi and less porous spaces. Overall, our study found that 3% salt would be suitable for 3D printing ink using fish surimi.

• Resources Recycling
• /
• v.27 no.1
• /
• pp.3-13
• /
• 2018

3D printing, also known as Additive Manufacturing (AM), is being positioned as a new business model of revolutionizing paradigms of existing industries. Launched in early 2000, 3D printing technology for architecture has also advanced rapidly in association with machinery and electronics technologies mostly in the United States and Europe. However, 3D printing systems for architecture require different mechanical characteristics from those of cement/concrete raw materials used in existing construction methods. Accordingly, in order to increase utilization of raw materials produced in the cement and resource recycling industry, it is necessary to develop materials processing and utilization technology, to secure new property evaluation and testing methods, and to secure database related to environmental stability for a long period which aims to reflect characteristics of an architectural 3D printing technology.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.3.1-3.1
• /
• 2011

Over the past decade, the major efforts for lowering the cost of electronics has been devoted to increasing the packaging efficiency of the integrated circuits (ICs), which is defined by the ratio of all devices on system-level board compared to the area of the board, and to working on a larger but cheaper substrates. Especially, in flexible electronics, the latter has been the favorable way along with using novel nanomaterials that have excellent mechanical flexibility and electrical properties as active channel materials and conductive films. Here, the tool for achieving large area patterning is by printing methods. Although diverse printing methods have been investigated to produce highly-aligned structures of the nanomaterials with desired patterns, many require laborious processes that need to be further optimized for practical applications, showing a clear limit to the design of the nanomaterial patterns in a large scale assembly. Here, we demonstrate the alignment of highly ordered and dense silicon (Si) NW arrays to anisotropically etched micro-engraved structures using a simple evaporation process. During evaporation, entropic attraction combined with the internal flow of the NW solution induced the alignment of NWs at the corners of pre-defined structures. The assembly characteristics of the NWs were highly dependent on the polarity of the NW solutions. After complete evaporation, the aligned NW arrays were subsequently transferred onto a flexible substrate with 95% selectivity using a direct gravure printing technique. As proof-of-concept, flexible back-gated NW field effect transistors (FETs) were fabricated. The fabricated FETs had an effective hole mobility of 0.17 $cm2/V{\cdot}s$ and an on/off ratio of ${\sim}1.4{\times}104$. These results demonstrate that our NW gravure printing technique is a simple and effective method that can be used to fabricate high-performance flexible electronics based on inorganic materials.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.386-392
• /
• 2020

The self-weight of the 3D printing concrete increases with increasing printing height. Therefore, the lower layer must be hardened within a suitable time to secure continuous printing performance. In particular, the hardening speed of concrete is slow in the winter season when the temperature was low. Hence, the early strength of 3D printing concrete requires improvement. In domestic and international literature, cases of increasing the early strength of concrete using inorganic chemical additives, such as amine-based, nitrate-based, sodium-based, and calcium-based, have been reported. In this study, early strength improvement-type additive samples (amine-based, nitrate-based, sodium-based) were prepared, and their performance was evaluated. When using a nitrate-based additive, the early strength was increased significantly in a 10 ℃ environment. In addition, it was possible to secure a higher early strength than the existing 3D printing concrete mixed at 20 ℃.

• Journal of Radiation Industry
• /
• v.17 no.2
• /
• pp.173-181
• /
• 2023

3D printing is a technology that can transform and process computerized data obtained through modeling or 3D scanning via CAD. In the medical field, studies on customized 3D printing technology for clinical use or patients and diseases continue. The importance of research on filaments and molding methods is increasing, but research on manufacturing methods and available raw materials is not being actively conducted. In this study, we compare the characteristics of each material according to the manufacturing method of the phantom manufactured with 3D printing technology and evaluate its usefulness. We manufactured phantoms of the same size using poly methyl meta acrylate (PMMA), acrylonitrile butadiene styrene (ABS), and Poly Lactic Acid (PLA) based on the international standard phantom of aluminum step wedge. We used SITEC's radiation generator (DigiRAD-FPC R-1000-150) and compared the shielding rate and line attenuation coefficient through the average after shooting 10 times. As a result, in the case of the measured dose transmitted through each phantom, it was confirmed that the appearance of the dose measured for phantoms decreased linearly as the thickness increased under each condition. The sensitivity also decreased as the steps increased for each phantom and confirmed that it was different depending on the thickness and material. Through this study, we confirmed that 3D printing technology can be usefully used for phantom production in the medical field. If further development of printing technology and studies on various materials are conducted, it is believed that they will contribute to the development of the medical research environment.

• Journal of the Korean Ceramic Society
• /
• v.56 no.4
• /
• pp.360-364
• /
• 2019

PZT suspensions for photo-curable 3D printing were fabricated and their characteristics were evaluated. After mixing the PZT, photopolymer, photo-initiator, and dispersant for 10 min by using a high-shear mixer, the viscosity characteristics were investigated based on the powder content. To determine an appropriate dispersant content, the dispersant was mixed at 1, 3, and 5 wt% of the powder and a precipitation test was conducted for two hours. Consequently, it was confirmed that the dispersibility was excellent at 3 wt%. Through thermogravimetric analysis, it was confirmed that weight reduction occurred in the photopolymer between 120? and 500?, thereby providing a debinding heat treatment profile. The fabricated suspensions were cured using UV light, and the polymer was removed through debinding. Subsequently, the density and surface characteristics were analyzed by using the Archimedes method and field-emission scanning electron microscopy. Consequently, compared with the theoretical density, an excellent characteristic of 97% was shown at a powder content of 87 wt%. Through X-ray diffraction analysis, it was confirmed that the crystallizability improved as the solid content increased. At the mixing ratio of 87 wt% powder and 13 wt% photo-curable resin, the viscosity was 3,100 cps, confirming an appropriate viscosity characteristic as a stereolithography suspension for 3D printing.

• Current Photovoltaic Research
• /
• v.9 no.1
• /
• pp.6-10
• /
• 2021

The mesh mask screen, which is generally used for screen printing metallization of silicon solar cell, requires high squeegee pressure and low printing speed. These requirements are acting as a limiting factor in production yield in photovoltaic industries. In order to improve the productivity, a metal mask, which has high durability and high printing speed, has been researched. In this paper, the characteristics of each solar cell, in which electrodes were formed by using a metal mask and a mesh mask, were analyzed through recombination current density. In particular, the metal-induced recombination current density (Jom) representing the recombination of the emitter-metal interface was calculated using the shading method, and the resulting efficiency and open-circuit voltage were analyzed through the diode equation. As a result of analyzing the proportion of the metal-induced recombination current density to the total emitter recombination current density, it was analyzed that the reduction of the metal-induced recombination current density through the metal mask is an important factor in reducing the total recombination current density of the solar cell.