• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.1.1-1.1
• /
• 2011

Printed electronics based on the direct writing of solution processable functional materials have been of paramount interest and importance. In this talk, the synthesis of printable inorganic functional materials (conductors and semiconductors) for thin-film transistors (TFTs) and photovoltaic devices, device fabrication based on a printing technique, and specific characteristics of devices are presented. For printable conductor materials, Ag ink is designed to achieve the long-term dispersion stability and good adhesion property on a glass substrate, and Cu ink is sophisticatedly formulated to endow the oxidation stability in air and even aqueous solvent system. The both inks were successfully printed onto either polymer or glass substrate, exhibiting the superior conductivity comparable to that of bulk one. In addition, the organic thin-film transistor based on the printed metal source/drain electrode exhibits the electrical performance comparable to that of a transistor based on a vacuum deposited Au electrode. For printable amorphous oxide semiconductors (AOSs), I introduce the noble ways to resolve the critical problems, a high processing temperature above $400^{\circ}C$ and low mobility of AOSs annealed at a low temperature below $400^{\circ}C$. The dependency of TFT performances on the chemical structure of AOSs is compared and contrasted to clarify which factor should be considered to realize the low temperature annealed, high performance AOSs. For photovoltaic application, CI(G)S nanoparticle ink for solution processable high performance solar cells is presented. By overcoming the critical drawbacks of conventional solution processed CI(G)S absorber layers, the device quality dense CI(G)S layer is obtained, affording 7.3% efficiency CI(G)S photovoltaic device.

• Korean Journal of Materials Research
• /
• v.2 no.3
• /
• pp.163-171
• /
• 1992

The $SnO_2/TiO_2$ thick film type humidity sensing devices containing 5 to 50 wt% $TiO_2$ have been fabricated by a typical screen printing technique. The surface crystal structure and microstructure were investigated by XRD, SEM and FTIR analyses. And the measurement of sensing characteristics of the thick film devices have been carried out. The crystalline phase of the thick flus were mainly identified as $(SnO_2){\cdot}6T$ crystal structure with XRD analysis, and the thick films sintered at $1300^{\circ}C$ showed an average particle size of $2.0{\mu}m$. The $SnO_2/TiO_2$ device sintered at $1300^{\circ}C$ containing 10 wt% $TiO_2$ showed high sensitivity to humidity in the range of R.H. 20-90%.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.6
• /
• pp.122-128
• /
• 2016

The Biosensor biosensor pattern was developed by via an EHD (electro-hydro-dynamics (EHD) patterning process that was performed under atmospheric pressure at room temperature in a single step. The drop diameter was smaller than nozzle diameter and applied high viscosity conductive ink was applied in the EHD patterning method to provide a clear advantage over the piezo and thermal inkjet printing techniques. The Biosensor's biosensor's micro electrode pattern was printed by via a continuous EHD patterning method using 3three- type types of control parameters parameter (input voltage, patterning speed, nozzle pressure). High viscosity (1000 cps) conductive ink with 75 wt% of silver nanoparticles was used for experimentation. The incremental result of impedance of biosensor impedance was measured between the antibody ($10ug{\mu}g/ml$) to spore (0.1 ng/ml, 10 ng/ml, and $1ug{\mu}g./ml$) reaction at frequency 493 MHz frequency.

• Fashion & Textile Research Journal
• /
• v.17 no.6
• /
• pp.988-995
• /
• 2015

Gaps between the upper edges of brassiere mold cups and the breasts are one of the most serious issues in realizing comfort wearing of commercial brassieres for small-breasted women. The surplus ease amounts causing the fit problem were measured from 3D wearing images of the small-breasted women's brassieres. The effect after the removing the surplus ease amounts from the upper edge of mold cup was approved by subjective wearing evaluation. Since the volume distribution of mold cup can also affect the wearing sensation of brassiere, the subjective wearing sensation was compared for two brassieres of different volume distributions, V_L, of which volume was concentrated at the lower cup, and V_C, which has the thickest part at the nipple. As the results, the suitable sensation for cup volume and the natural wearing silhouette could be accomplished by removing the surplus ease amounts from the upper edge of mold cup to reduce the gaps between brassieres and the breasts, which could be accomplished through an approach reducing the volume near the upper edge of mold brassiere cup and making the volume concentrated at the lower cup. These works provide a useful information on the design of the brassiere mold cups for small-breasted women. Moreover, modeling methods of 3D scan data and 3D printing technique for making more accurate mold cases used in this research can be helpful to develop and evaluate clothing products in future.

• The Korean Journal of Nuclear Medicine
• /
• v.3 no.2
• /
• pp.55-63
• /
• 1969

In the past few years, scintigraphy has become increasingly important in clinical practice, and the use of a color-printing technique has permited a more accurate interpretation of the scan image. Our liver color scintigrams consist of 51 hepatomas, 35 liver cirrhosis, 22 liver abscessis, 10 hepatitis and other 13 cases of the liver diseases which were clinically arid pathologically diagnosed at Sevarance Hospital, Yonsei Univ., since Feb. 1969 through Sept. 1969. These scintigrams have been analized in terms of various pathologic morphology, such as size, shape, margin of the liver, distribution of radioactivity, and shape of the space occupying lesions. The results are as follows: 1. Enlargement of the liver was the most common finding in the diseased livers. The Rt. lobe enlargement was particularly prominent in the liver abscess. 2. Irregular distribution of radioactivity in the liver (so called mottling) was present in 78% of hepatoma, while it was seen only in 31% of liver abscesses. 3. Liver cirrhosis tends to show perihilar accumulation of the isotope (57%). 4. The deformity of the lower most angle of the Rt. lobe, and the Lt. lateral margin of the Lt. lobe was also impressive throughout the cases ($74{\sim}95%$ of all diseased livers). 5. The frequency of visualization of the spleen was influenced by the size of space occupying lesions and the amount of functioning liver. 6. Differentiation between the liver abscess and hepatoma seems to be possible on scintigram, when shape and margin of defect and patterns of distribution of radioactivity in the remaining liver are clearly demonstrated.

• Journal of Sensor Science and Technology
• /
• v.4 no.2
• /
• pp.37-44
• /
• 1995

A coprecipitation method was used for preparing Ca and Pt doped $SnO_{2}$-based material. Crystallite size and specific surface area were investigated by TEM, XRD and BET analysis. $SnO_{2}(Ca)/Pt$ based thick film devices were prepared by a screen printing technique for hydrocarbon gas detecting. Then the electrical and sensing characteristics of devices were investigated. As Ca and Pt addition, the crystal growth of $SnO_{2}$ was suppressed during calcining and sintering, and the sensitivity of $SnO_{2}(Ca)/Pt$ thick film to gas was enhanced. Also any difference in the sensing properties has to be attributed to the Pt and Au electrode. For the 2000 ppm $CH_{4}$, the sensitivity of $SnO_{2}(Ca)/Pt$ thick film devices were about 83% at an operating temperature of $400^{\circ}C$.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.45 no.3
• /
• pp.32-41
• /
• 2008

In this paper, we describe the synthesis of robust and non-fragile $H^{\infty}$ state feedback controllers for linear systems with affine parameter uncertain tracking servo system of blu-ray disc drive, as well as static state feedback controller with polytopic uncertainty Similarity any other control system, the objective of the track-following system design for optical disc drives is to construct the system with better performance and robustness against modeling uncertainties and various disturbances. Also, the obtained condition can be rewritten as parameterized linear matrix inequalities(PLMIs), that is, LMIs whose coefficients are functions of a parameter confined to a compact set. We show that the resulting controller guarantees the asymptotic stability and disturbance attenuation of the closed loop system in spite of controller gain variations within a resulted polytopic region.

• Journal of the Korean Society of Costume
• /
• v.53 no.6
• /
• pp.11-23
• /
• 2003

Japonese woodblock printing has been accepted with a great curiosity at first, and it has been called as 'Japonisme' or 'Japonaiserie' in which the school of Impressionism accepted the Japanese type of art and developed it in Europe. The term of Japonisme is the concept that does not refer to one style but to the taste for Japanese painting, craft, fashion and the like in Europe proved as the historical phenomenon through Japanese works. That is, it means every Japanese disposition including all artistic techniques and contents relating to Japanese tastes in Europe. Fashion of dress as Japanese expressed in European painting works not only symbolizes the 'modernity' expressive of the aspiration and nostalgia for Japan but presents the Japan of exotic taste as the inquisitive object of sexual interest. And the expressive method of the peculiar the beauty of the body was described in Japanese painting works because of the fashion characteristics that the frontal side of Japanese clothing was presented in a more decorative and formative way than its reverse side due to decorative design and belts. It could be found that this was introduced actively into the painting works of the impressionist school. This study attempts to discuss the expressive style including the pictorial style, technique and theme shown in the accommodating process of Japanese painting in the Impressionistic school and investigate the phenomenon of Japonisme that was conducted in the western Europe. Accordingly, this study attempts to find out that clothing takes an important place as the aesthetic category of one historical point in time by investigating the Japanese clothing of the times shown in impressionist painting works and that clothing forms the stylistic characteristics and formative characteristics of painting. It could be found that dress existed not only as the instrument capable of illustrating the aesthetic attitude or will of the human being as visual identity but as plastic art and became the prime mover for reinterpreting and changing the plastic style of art frontier.

• Korean Journal of Materials Research
• /
• v.11 no.4
• /
• pp.272-277
• /
• 2001

NiO-doped $WO_3$ thick films were prepared by a screen printing technique. The electrical Property and microstructure of the films were investigated with the partial pressure of oxygen and the amount of NiO. The grain size of NiO-doped $WO_3$ was smaller than that of undoped $WO_3$ but the grain sixte of 0.1, 1, 10 mol% NiO-doped$ WO_3$ were nearly the same. The electrical conductance of the $WO_3$ thick films decreased with the oxygen partial pressure, and increased with the amount of NiO to the limit of solid solution. The variation of the electrical conductance with temperature is not so large in the extrinsic region, but it changed rapidly in the intrinsic region. The conductance decreased with adsorption of oxygen in the intermediate range between the extrinsic and intrinsic region.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.7
• /
• pp.607-612
• /
• 2017

Recently, additive manufacturing (AM) technology, also known as 3D printing technology, has attracted attention as an innovative production method to fabricate functional components having complex shapes with saving materials. In particular, a fabrication of poly lactic acid (PLA) parts through a fused deposition modeling (FDM) technique has attracted much attention in the medical field. In this paper, an experimental study on the identification of dominant process parameters influencing mechanical properties of PLA parts fabricated by the FDM process is conducted, and their optimal values for maximizing the mechanical properties are obtained. Three process parameters are considered in this research, namely, layer thickness, a part orientation and in-fill. It is known that thin layer thickness, part orientation diagonal to the tension direction, and full in-fill are optimal conditions to maximize the mechanical properties.