• 한국진공학회지
• /
• 제10권1호
• /
• pp.31-36
• /
• 2001

열산화시킨 $SiO_2$ 박막의 두께와 입사 전류의 양에 따라 이차전자 방출 계수를 측정하였다. $930^{\circ}C$에서 열산화시킨 $SiO_2$ 박막 두께는 58nm, 19nm, 43nm, 79nm, 95nm, 114nm였으며 이들의 이차전자의 방출 특성이 박막 두께와 전류량에 따라 변화하는 것을 확인하였다. 박막 두께 43 nm 이하의 얇은 박막에서는 대체적으로 universal curve의 형태를 따르지만 79 nm 이상의 두꺼운 박막에서는 이차전자 방출곡선이 최고점이 2개인 형태로 변하며 그 값도 전반적으로 낮아진다. 또 입사시키는 일차전자 전류의 증가에 대해서도 이차전자 방출곡선이 전체적으로 낮아진다. 이 실험에서 측정된 최대 이차전자 방출 계수는 박막 두께 19 nm, 일차 전자 에너지 300 eV 일차 전류 0.97 $\mu\textrm{A}$일 때 3.35를 갖는다. 이차전자 방출계수가 최대인 입사에너지에서 전자의 시료내 침투깊이와 탈출깊이와의 관계식을 통하여 박막 두께를 이론적으로 계산하였으며, 실험값과 비교적 일치하는 것을 확인하였다.

• 소성∙가공
• /
• 제14권4호
• /
• pp.319-326
• /
• 2005

In this study, the nano-deformation behavior of semi-solid Al-Si alloy was investigated using a molecular dynamics simulation as a part of the research on the surface crack behavior in thixoformed automobile parts. The microstructure of the grain-size controlled Al-Si alloy consists of primary and eutectic regions. In eutectic regions the crack initiation begins with initial fracture of the eutectic silicon particles and inside other intermetallic phases. Nano-deformation characteristics in the eutectic and primary phase of the grain-size controlled Al-Si alloy were investigated through the molecular dynamics simulation. The primary phase was assumed to be single crystal aluminum. It was shown that the vacancy occurred at the zone where silicon molecules were.

• 한국주조공학회지
• /
• 제16권6호
• /
• pp.565-575
• /
• 1996

In this study, to gain the semi-solid alloy we employed the electromagnetic rotation by a induction motor of 3-phases and 2-poles for Al-7wt%Si alloy and observed the size of primary solid particle, distribution state of primary solid particle, the degree of sphericity, and fraction of primary solid for the evaluation of its results. The size of primary solid particle increases from $98{\mu}m$ to $118{\mu}m$ as solid fraction increases from 0.2 to 0.5. The degree of sphericity increased as the solid fraction increased. Solid particles obtained from the microstructures of isothermally held sample were coarsened and the degree of sphericity was enhanced as isothermal holding time increased. However, when the sample was stirred for more than 40min, solid particles merged together and liquid phase was entrapped within the cluster of solid particles. The size of primary solid particle was not changed significantly with the variation of input voltages by 160V over which solid particles began to merge together to be a large cluster of about $170{\mu}m$ at 180V. The standard deviation and the degree of sphericity were not changed significantly with the variation of input voltage.

• 대한금속재료학회지
• /
• 제49권11호
• /
• pp.874-881
• /
• 2011

The present study describes a new technique to extract the primary silicon from an Al-Si alloy melt using centrifugal force during its solidification. The primary silicon was separated from an Al-50 wt.%Si alloy by centrifugal force in the form of a foam, which facilitated subsequent acid leaching to extract the pure silicon due to its wide surface area. The foam recovery after centrifugal separation was decreased as centrifugal acceleration was increased. The final recovery after acid leaching became closer to the solid fraction of the alloy, which was calculated from the Al-Si binary phase diagram, with increasing centrifugal acceleration due to the effective removal of the attached Al on the foam. The purity of the primary silicon obtained by the centrifugal separation method was over 99.99%, with only aluminum being also present.

• 한국주조공학회지
• /
• 제29권2호
• /
• pp.78-85
• /
• 2009

Functionally graded microstructure of centrifugal cast Al-Si alloy, especially distribution of primary Si particles according to the changes of melt pouring temperature and rotation frequency was investigated by numerical simulation. Moving velocity of Si particles increased as the melt pouring temperature and rotational frequency of mold increased. Therefore, segregation tendency of primary Si particles toward inner side of cylindrical sample increased as the melt pouring temperature and rotational frequency of mold increased. Rich distribution region of particles was located at 0.9, 0.7, 0.4 mm from inner surface of cylindrical sample under the centrifugal cast condition of $750^{\circ}C$ melt pouring temperature and 1500, 2000 and 2500 rpm mold rotational frequencies, respectively, by numerical simulation.

• 한국농촌간호학회지
• /
• 제3권2호
• /
• pp.75-80
• /
• 2008

This profile presents a brief overview of the past and current primary health care of Saje PHCP in Wonju Si, Kangwon-Do, Korea. Because of the increasing in the proportion of the elderly in the population and the vulnerability among groups, they are one of the main targets of the PHC through programs such as chronic disease management, health promotion activities (exercise, diet, smoking and alcohol control). Curative services have been decreased and preventive services have been increased.

• 한국주조공학회지
• /
• 제18권4호
• /
• pp.349-356
• /
• 1998

In this study, the influence of impurity element Ca, P on solidification behavior and morphology of eutectic silicon was examined by observation of microstructure and by DSC analysis. In the case of 1.3 ppm P, eutectic Si was fine and fibrous when the added amount of Ca was 500 ppm, However, the modification of eutectic Si was depressed by formation of polygonal Ca-Si compounds when the addition amount of Ca was greater than 1000 ppm. The addition of Ca 500 ppm depressed the primary and eutectic temperature. The primary and eutectic temperature were depressed with Ca 500 ppm but rather ascended when the addition amount of Ca was more than 1000 ppm. When the content of P was 17.5 ppm, eutectic Si had modified morphology with Ca addition. DAS was increased, the primary temperature was ascended and eutectic temperature was depressed with Ca added. Eutectic Si appeared as coarse flake phase and DAS was decreased with the increase of P content. The existence of P in the melt depressed the primary temperature and ascended eutectic temperature.

• 한국주조공학회지
• /
• 제15권4호
• /
• pp.416-421
• /
• 1995

Recently Al-Cu-P alloys are used to refine primary Si of hypereutectic Al-Si alloys. Because it has inside AlP compound that acts as nucleation site in the melt, Al-Cu-P alloy has good refinement effect in lower holding temperature and after shoter holding times. In this study Al-Cu-P refinement agent was made by mechanical alloying method. When Al-13.5wt%Cu-1.5wt%P was alloyed mechanically for 30hr in Ar atmosphere by high energy ball mill, it had the refinement effect that showed primary Si size of about $30{\mu}m$ in Al-20wt%Si at $760^{\circ}C$, treated for 15min.

• 한국안전학회지
• /
• 제15권4호
• /
• pp.35-40
• /
• 2000

The influence of cyclic loading history on the creep behavior of the 30 vol% hot-pressed $SiC_f/Si_3N_4copmposite was experimentally investigated at $1200^{\circ}C$. The duration of loading/unloading had great effects on the creep behaviors. The short term duration cyclic loading history test results showed significant reduction in the primary and steady-state creep rates. For example, 300sec loading/300sec unloading history resulted in 70% lower steady-state creep rate than that of the continuous loading. However the long term duration cyclic loading history test results showed little change in creep rates compared to those of the continuous one. The reason for the significant change in the short term duration cycles was estimated due to the change in the stress redistribution between the fiber and matrix during the creep recovery in the primary stage.

• 한국주조공학회지
• /
• 제16권2호
• /
• pp.116-123
• /
• 1996

The equipment for the horizontal continuous casting was built to produce hyper-eutectic Al-Si bars with a small cross-section of 25mm in diameter. The manufacturing processes including withdrawal cycle and secondary cooling methods were modified to refine the primary and the eutectic Si. The longitudinal casting speeds varied over the ranges of 670-1100mm/min for pure Al, and 200-350mm/min for Al-17wt%Si alloy. Due to the difference of cooling rate in the mould, microstructural asymmetry between the lower and the upper part of bar was observed. Thus, manufacturing processes such as cooling and withdrawal method were optimally combinated to get the homogeneous cast structure. With the increase of casting speed, the primary Si size was refined down to $30{\mu}m$ near the surface, and $80{\mu}m$ in the center of the bar.