• 한국세라믹학회지
• /
• 제31권5호
• /
• pp.552-560
• /
• 1994

A composite of TiB2-Al2O3 system was successfully prepared from a mixture of TiO2, B2O3, and Al by self-propagating high temperature synthesis (SHS) with a novel characteristic, utilizing the internal oxidation heat of aluminium metal of the mixture, instead of by a conventional technique, externally heating a mixture of Ti, B and Al2O3. From a mixture with B/Ti molar ratio of =2.0, pure two phases of TiB2 and $\alpha$-Al2O3 with good crystallinity and small, uniform sizes were formed. However, when the B/Ti molar ratio of the mixture goes to a value less than 2.0, in addition to the above main minerals, a small smounts of metastable phases such as TiB and Ti3B4 were formed. It was found that about 60%, the optimum green density of compacts gave their highest reaction rate and temperature during SHS process. TiB2-Al2O3 system composite with B/Ti molar ratio of =2.0 could be pressurelessly sintered even at 190$0^{\circ}C$ under Ar gas flows without any addition of sintering aids, showing their good properties such as 91.2% in relative density, 2750 kgf/$\textrm{mm}^2$ in Vickers hardness and 2620 kgf/$\textrm{cm}^2$ in flexural strength.

• 한국세라믹학회지
• /
• 제48권2호
• /
• pp.152-159
• /
• 2011

The green and hard machining characteristics of dental ceramics are of great interest to dental industry. The green bodies of TZP/$Al_2O_3$ composites were prepared by the cold isostatic pressing, and machined on the CNC lathe using PCD (polycrystalline diamond) insert under various machining conditions. With increasing nose radius of PCD insert, surface roughness initially increased due to increased cutting resistance, but decreased by the onset of sliding fracture. The lowest surface roughness was obtained at spindle speed of 1,300 rpm and lowest feed rate. Hard bodies were prepared by pressureless sintering the machined green bodies at several temperatures. The grinding test for sintered hard body was conducted using electroplated diamond bur with different grit sizes. During grinding, grain pull out in the composite was occurred due to thermal expansion mismatch between the alumina and zirconia. The strength of the composite decreased with alumina contents, due to increased surface roughness and high monoclinic phase transformed during grinding process. The final polished samples represented high strength by the elimination of a phase transformation layer.

• 한국분말재료학회지
• /
• 제21권6호
• /
• pp.447-453
• /
• 2014

Effect of oxygen content in the ultrafine tungsten powder fabricated by electrical explosion of wire method on the behvior of spark plasma sintering was investigated. The initial oxygen content of 6.5 wt% of as-fabricated tungsten powder was reduced to 2.3 and 0.7 wt% for the powders which were reduction-treated at $400^{\circ}C$ for 2 hour and at $500^{\circ}C$ for 1h in hydrogen atmosphere, respectively. The reduction-treated tungsten powders were spark-plasma sintered at $1200-1600^{\circ}C$ for 100-3600 sec. with applied pressure of 50 MPa under vacuum of 0.133 Pa. Maximun sindered density of 97% relative density was obtained under the condition of $1600^{\circ}C$ for 1h from the tungsten powder with 0.7 wt% oxygen. Sintering activation energy of $95.85kJ/mol^{-1}$ was obtained, which is remarkably smaller than the reported ones of $380{\sim}460kJ/mol^{-1}$ for pressureless sintering of micron-scale tungsten powders.

• The Korean Journal of Ceramics
• /
• 제3권3호
• /
• pp.199-207
• /
• 1997

$Al_2O_3$/SiC particulate composites were fabircated by pressureless sintering. The dispersed phase was SiC of which the content was varied from 1.0 to 10 vol%. Three SiC powders having different median diameters from 0.28 $\mu\textrm{m}$ to 1.9 $\mu\textrm{m}$ were used. The microstructure became finer and more uniform as the SiC content increased except the 10 vol% specimens, which were sintered at a higher temperature. Under the same sintering condition, densification as well as grain growth was retarded more severly when the SiC content was higher or the SiC particle size was smaller. The highest flexural strength obtained at 5.0 vol% SiC regardless of the SiC particle size seemed to be owing to the finer and more uniform microstructures of the specimens. Annealing of the specimens at $1300^{\circ}C$ improved the strength in general and this annealing effect was good for the specimens containing as low as 1.0 vol% of SiC. Fracture toughness did not change appreciably with the SiC content but, for the composites containing 10 vol% SiC, a significantly higher toughness was obtained with the specimen containing 1.9$\mu\textrm{m}$ SiC particles.

• 한국세라믹학회지
• /
• 제30권11호
• /
• pp.881-890
• /
• 1993

MAS system has narrow sintering temp. range due to the liquid phae sintering and thereby densify rapidly. And especially, its poor mechanical properties limitedthe industrial application. In this study, the improvement of mechanical properties and densification is suggested by the consideration of the toughening mechanisms and isolated pore generation mechanism which is derived by the liquid phase sintering theory in 3Y-TZP added composites. After Pressureless sintering up to 140$0^{\circ}C$ for 5hr, the dihedral angle and contact angle are analyzed by the observation of microstructure. As a result of microstructure analysis, the sintering stage of the specimen sintered for 5hr is analyzed as solid-skeleton stage. And the isolated pore generation mechanisms are considered as (1) The swelling of the liquid phase is predominent due to the facts that dihedral angle is larger than 60$^{\circ}$, contact angle is large and that liquid volume fraction is smaller than 10%. (2) The porous characteristics of the MAS system is also suggested as: the SiO2-rich liquid film is firstly formed at the srface and therefore this reduces the contiguity of the pore, which induces the isolated pore. The strength and fracture toughness increased with the addition of 3Y-TZP and the main fracture toughness improvement mechanisms are analyzed as the crack deflection.

• 한국결정성장학회지
• /
• 제9권2호
• /
• pp.260-265
• /
• 1999

$\alpha$-SiC에 ${\alpha}-Si_3N_4$ 를 10~30 vol%까지 10 vol% 간격으로 혼합하고 소결 조제로$Al_2O_3$와$Y_2O_3$를 각각 6wt% 로 첨가하여 $1,780^{\circ}C$에서 2시간동안 질소 분위기에서 상압소결하여 $Si_3N_4$ 복합체를 제조하였다. 상대 이론 밀도 및 꺽임 강도는 ${\alpha}-Si_3N_4$를 20 vol% 첨가하였을 때 92% 및 3,560 MPa로 가장 우수하였으며, 비마모량도 $2.68{\times}10^{-3}\;mm^2$ 으로 가장 작았다. 그리고, 파괴 인성$(K_{1c})$)은 ${\alpha}-Si_3N_4$를 30vol% 첨가하였을 때 $4.9\;MN/m^{3/2}$로 가장 좋았으나 이 경우 기공의 영향으로 내마모성은 저하된 것을 확인할 수 있었다.

• 한국세라믹학회지
• /
• 제25권3호
• /
• pp.231-236
• /
• 1988

$Al_2O_3$ 기지에 미치는 2차상의 영향을 알아보기 위하여 SiC 입자를 5~20vol.% 분산시키고 소결조제로서 $TiO_2$ 또는 RY_2O_3$를 2.5wt.%첨가하여 180$0^{\circ}C$, $N_2$분위기 중에서 90분간 상압소결 하였다. SiC함량이 증가함에 따라 소결체의 밀도는 감소하였지만 기계적 물성은 증가하여 $Y_2O_3$를 소결조제로 첨가한 경우, 꺾임강도는 525MPa, 경도는 17.1GPa,파괴인성은 4.1 MPa.$m^{1/2}$ 정도의 최고값을 나타내었고 반면 $TiO_2$를 소결조제로 첨가한 경우 꺾임강도 285MPa , 경도 12.1GPa 정도의 값을 나타냈다. 그리고 이와 같은 기계적 물성의 증진은 주로 SiC의 복합화에 따른 균열의 편향과 $Al_2O_3$ 의 입자성장억제효과에 의한 것으로 밝혀졌다.

• 한국세라믹학회지
• /
• 제44권6호
• /
• pp.291-296
• /
• 2007

Porous $Al_2O_3-(m-ZrO_2)$ composites were fabricated by pressureless sintering, using different volume percentages (40% - 60%) of poly methyl methacrylate (PMMA) powders as a pore-forming agent. The pore-forming agent was successfully removed, and the pore size and shape were well-controlled during the burn-out and sintering processes. The average pore size in the porous $Al_2O_3-(m-ZrO_2)$ bodies was about $200\;{\mu}m$ in diameter. The values of relative density, bending strength, hardness, and elastic modulus decreased as the PMMA content increased; i.e., in the porous body (sintered at $1500^{\circ}C$) using 55 vol % PMMA, their values were about 50.8%, 29.8 MPa, 266.4 Hv, and 6.4 GPa, respectively. To make the $Al_2O_3-(m-ZrO_2)$/polymer hybrid composites, a bioactive polymer, such as PMMA, was infiltrated into the porous $Al_2O_3-(m-ZrO_2)$ composites. After infiltration, most of the pores in the porous $Al_2O_3-(m-ZrO_2)$ composites, which were made using 60 vol % PMMA additions, were infiltrated with PMMA, and their values of relative density, bending strength, hardness, and elastic modulus remarkably increased.

• 마이크로전자및패키징학회지
• /
• 제29권4호
• /
• pp.41-47
• /
• 2022

Ag sintering technologies have received great attention as it was applied to the inverter of Tesla's electric vehicle Model III. Ag sinter bonding technology has advantages in heat dissipation design as well as high-temperature stability due to the intrinsic properties of the material, so it is useful for practical use of SiC and GaN devices. This study was carried out to understand the sinter joining temperature effect on the robust Ag sintered joints in air without pressure within 10 min. Electroplated Ag finished Cu dies (3 mm × 3 mm × 2 mm) and substrates (10 mm × 10 mm × 2 mm) were introduced, respectively, and nano Ag paste was applied as a bonding material. The sinter joining process was performed without pressure in air with the bonding temperature as a variable of 175 ℃, 200 ℃, 225 ℃, and 250 ℃. As results, the bonding temperature of 175 ℃ caused 13.21 MPa of die shear strength, and when the bonding temperature was raised to 200 ℃, the bonding strength increased by 157% to 33.99 MPa. When the bonding temperature was increased to 225 ℃, the bonding strength of 46.54 MPa increased by about 37% compared to that of 200 ℃, and even at a bonding temperature of 250 ℃, the bonding strength exceeded 50 MPa. The bonding strength of Ag sinter joints was directly influenced by changes in the necking thickness and interfacial connection ratio. In addition, developments in the morphologies of the joint interface and porous structure have a significant effect on displacement. This study is systematically discussed on the relationship between processing temperatures and bonding strength of Ag sinter joints.

• 한국결정성장학회지
• /
• 제22권3호
• /
• pp.139-146
• /
• 2012

소뼈를 하소하여 천연 하이드록시아파타이트 분말을 얻은 다음, $1100^{\circ}C$ 및 $1200^{\circ}C$로 상압 소결하여 기공율이 각각 35 % 및 18 %인 다공성 하이드록시아파타이트를 제조한 후 이들 시편의 생체친화성을 평가하였다. 골아세포의 성장속도과 세포독성의 유무에 따라 평가되는 생체친화성은 MG-63 세포의 부착능과 분화되어 증식되는 세포의 수로 측정하였다. in vitro에서 세포 반응을 관찰한 결과 소뼈로부터 제조된 하이드록시아파타이트 시편은 독성이 없고 생체 친화성이 좋은 시편이었다. 세포배양 1일 후부터 하이드록시아파타이트 표면에 세포가 부착되었고, 세포배양 후 3일 후에는 핵 주위로 세포질이 퍼져나갔으며, 5일 후에는 부착된 세포의 수가 크게 증가하였다. 배양 초기에는 밀도에 관계 없이 세포의 부착능이 유사하였지만, 세포 배양 시간이 증가하면서 기공율이 높은 시편에서 세포의 부착 및 성장이 더 활발하게 진행되었다.