• 에너지공학
• /
• 제14권4호
• /
• pp.241-247
• /
• 2005

3열 정렬형 관군 배열에서 3열의 'common flow up'과 'common flow down' 형상의 와류발생기를 부착하여 와류발생기에 의한 열전달 촉진과 압력강하를 비교하였다 선행 연구자들이 제안한 'common flow down' 형상의 와류발생기는 와류발생기가 없는 휜-관군에 비해 열전달 촉진은 $10\%{\~}25\%$ 향상되었고, 압력강하는 $20\%{\~}35\%$ 증가하였다. 'common flow up' 형상의 와류발생기의 경우 후연 수평거리(${\Delta}y$)를 변화시키면서 평가하였다. 와류발생기는 삼각형과 사각형 형상을 적용하였다. 후연 수평거리(${\Delta}y$)가 5mm이고 삼각형의 'common flow up' 형상의 와류발생기가 정렬형 관군에서 설치될 때 Reynolds수(유로 높이의 배를 기준으로)가 $300{\~}2700$ 범위에서 열전달촉진은 10까지 향상하였고, 동시에 압력강하는 $8\%{\~}15\%$ 감소하였다. 삼각형 와류발생기가 부착된 휜-관군의 성능이 상대적으로 작은 압력강하 때문에 사각형 와류발생기가 부착된 휜-관군의 성능보다 좋게 나타났다.

• Design & Manufacturing
• /
• 제13권2호
• /
• pp.37-43
• /
• 2019

This study conducted a research as to condensation heat transfer friction loss headby using three types of flat micro multi-channel tubes with different processing of micro-fin and number of channels inside the pipes and different sizes of appearances. In addition, identical studies were conducted by using smoothing circular tubes with 5mm external diameter to study heat enhancement factor and pressure drop penalty factor. 1) The friction head loss showed an increase as the vapor quality and mass flux increased. In case of saturation temperature, it shows an increase as it gets lower. These factors are the reason occurring as the lower the saturation temperature is, the higher the density of refrigerant vapor gets. The influence of heat flux is similar as the dryness is low, but as it gets higher, it lowers in heat flux, and as the high temperature of high heat flux, it is a factor that occurs as the density gets lower. 2) RMS error of the in case of friction head loss, it showed to be predicted as 0.45~0.67 by Chisholm, Friedel, Lockhart and Martinelli. 3) As forfriction head loss penalty factor, the smaller the aspect ratio is, the larger the penalty factor gets, and as for the effect of micro-fin, the penalty factor increased because it decreases to the gas fluid the way groove for the refrigerant's flow.

• 한국자동차공학회논문집
• /
• 제17권5호
• /
• pp.91-96
• /
• 2009

The number of vehicles applied diesel engine are rapidly rising for fuel economy. Accompanying this trend, application of an after-treatment system is strictly required as a result of reinforced emission regulation. The Diesel Particulate Filter (DPF) system is considered as the most efficient method to reduce particulate matter by car makers but also in retrofit market. In this paper we discussed the optimization of active regeneration timing by comparing the fuel consumption from back pressure caused by PM loading and from active regeneration. The effects of back pressure of DPFs during PM loading, active regeneration condition and engine emission(PM) on additional fuel consumption are experimentally investigated and the proper regeneration timings according to DPF systems and fuel loss for 160,000km are determined.

• 동력기계공학회지
• /
• 제10권4호
• /
• pp.38-42
• /
• 2006

Pressure drops and friction factors in square channels with twisted tape inserts plus axial interrupted ribs are investigated. Tests are performed for Reynolds numbers ranging from 8,900 to 29,000. The rib height-to-channel hydraulic diameter, $e/D_h$, is kept at 0.057 and test section length-to-hydraulic diameter, $L/D_h$ is 30. The pressure drops and friction factor values are enhanced with axial interrupted ribs and twisted tape inserts. Square channels with twisted tape inserts plus axial interrupted ribs show the greatest pressure loss penalty in the present work. Friction factor data obtained for the square channel with twisted tape inserts plus axial interrupted ribs are less than those in the past publications for circular tubes with axial interrupted ribs and twisted tape inserts.