• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.12
• /
• pp.51-59
• /
• 1993

A 4${\times}10^{19}cm^{3}$ carbon-doped base AlGaAs/GaAs HBY was grown using carbontetracholoride(CCl$_4$) by atmospheric pressure MOCVD. Abruptness of emitter-base junction was characterized by SIMS(secondary ion mass spectorscopy) and the doping concentration of base layer was confirmed by DXRD(double crystal X-ray diffractometry). Mesa-type HBTs were fabricated using wet etching and lift-off technique. The base sheet resistance of R$_{sheet}$=550${\Omega}$/square was measured using TLM(transmission line model) method. The fabricated transistor achieved a collector-base junction breakdown voltage of BV$_{CBO}$=25V and a critical collector current density of J$_{O}$=40kA/cm$^2$ at V$_{CE}$=2V. The 50$\times$100$\mu$$^2$ emitter transistor showed a common emitter DC current gain of h$_{FE}$=30 at a collector current density of JS1CT=5kA/cm$^2$ and a base current ideality factor of ηS1EBT=1.4. The high frequency characterization of 5$\times$50$\mu$m$^2$ emitter transistor was carried out by on-wafer S-parameter measurement at 0.1~18.1GHz. Current gain cutoff frequency of f$_{T}$=27GHz and maximum oscillation frequency of f$_{max}$=16GHz were obtained from the measured Sparameter and device parameters of small-signal lumped-element equivalent network were extracted using Libra software. The fabricated HBT was proved to be useful to high speed and power spplications.

• Journal of the Korean Institute of Gas
• /
• v.8 no.3 s.24
• /
• pp.1-7
• /
• 2004

The polyethylene pipe can use semi-permanent because of the high corrosion resistance with chemical stability. In addition to, there is the merit that is an easy to establish and to maintain. However, as the reason that it is simply degraded when the polyethylene pipe was exposed to the outside, mainly it is used to lay under the ground with low-pressure gas transportation pipe. In this study, the nondestructive evaluation method was used to maintain the integrity of the polyethylene pipe. We simulated the various defects on the polyethylene pipes, and then the AE signal occurred according to the impact test of steel ball was evaluated by the acoustic emission method. From the results, the waveform and dominant frequency could be distinguishing from the defect shapes of polyethylene pipe. Especially, in the case of notch defect, the AE signals occur different by the angle and depth of the notch.

• Korean Chemical Engineering Research
• /
• v.50 no.2
• /
• pp.334-342
• /
• 2012

To know the role of 'the solid compressive pressure to the first solid layer of a cake, $p_d$' in the 'unified theory on solid-liquid separation', we analyzed extremely compressible cake formed with floc for the following three operations with our new concepts. First, the role of $p_d$ was studied in calculating the sediment thickness of floc, and in calculating the cake thickness in cake filtration performed with floc sediment. Second, we calculated the expression procedure using $p_d$. Finally, the influence of $p_d$ on cake thickness in hindered sedimentation, and on the calculation of the procedure of hindered sedimentation $p_d$ was verified. Thus the possibility of application of 'unified theory on solid-liquid separation' and the importance of $p_d$ was verified. Through these processes, new theoretical definitions of the cake filtration, expression and hindered sedimentation was established.

• Korean Chemical Engineering Research
• /
• v.45 no.6
• /
• pp.591-595
• /
• 2007

The membrane filter coated with nanostructured porous surface layer was made by heat treatment after depositing nanoparticles onto a conventional micron-fibrous metal filter as a substrate filter. The nanostructured porous layer membrane filter (NSPL-MF), whose the filtration performance was improved compared with the conventional metal membrane filters, was developed by coating the nanoparticle agglomerates of dendrite structure onto the micron-fibrous metal filter. Pressure drop of nanostructured porous layer membrane filter decreased with increasing the heat treatment temperature to make the nanostructured porous layer adhered on the filter surface because the nanoparticle agglomerates shrank, but filtration efficiency did not decrease clearly.

• Composites Research
• /
• v.13 no.4
• /
• pp.33-41
• /
• 2000

In this research, the mathematical modeling of the formation of SiC layer on the activated carbon was studied to improve the durability and the oxidation resistance of catalyst supports. SiC layer on the activated carbon was formed by permeating SiC from dichlorodimethylsilane(DDS) into pores and depositing while the porous structure was kept. The best conditions of manufacturing the support were found by studying the characteristics of SiC/C which was modelled under various deposition conditions. Changes of the amount of deposition, the pore diameter, the surface area with time were obtained by simulating convection, diffusion and reaction in an isothermal reactor at a steady state. The uniform deposition in the pores of samples was obtained at a lower concentration of the reactant and a lower pressure. Additionally, it was observed that the pore diameter and the surface area have points of inflection at certain times of deposition, because deposition occurred on the inside surface of the pore at first and then on the outside surface of the particle.

• Membrane and Water Treatment
• /
• v.9 no.4
• /
• pp.221-231
• /
• 2018

A new procedure to produce poly(vinylidene fluoride)/boron nitride hybrid membrane is presented for application in membrane distillation (MD) process. The influence of hexagonal boron nitride (h-BN) incorporation on the performance of the polymeric membranes is studied through the present investigation. For this aim, h-BN nanopowders were successfully synthesized using the simple chemical vapor deposition (CVD) route and subsequent solvent treatments. The resulting h-BN nanosheets were blended with poly(vinylidene fluoride) (PVDF) solution. Then, the prepared composite solution was subjected to phase inversion process to obtain PVDF/h-BN hybrid membranes. Various examinations such as scanning electron microscopy (SEM), wettability, permeation flux, mechanical strength and liquid entry pressure (LEP) measurements are performed to evaluate the prepared membrane. Moreover, Air gap membrane distillation (AGMD) experiments were carried out to investigate the salt rejection performance and the durability of membranes. The results show that our hybrid PVDF/h-BN membrane presents higher water permeation flux (${\sim}18kg/m^2h$) compared to pristine PVDF membrane. In addition, the experimental data confirms that the prepared nanocomposite membrane is hydrophobic (water contact angle: ${\sim}103^{\circ}$), has a porous skin layer (>85%), as well competitive fouling resistance and operational durability. Furthermore, the total salt rejection efficiency was obtained for PVDF/h-BN membrane. The results prove that the novel PVDF/h-BN membrane can be easily synthesized and applied in MD process for salt rejection purposes.

• Smart Structures and Systems
• /
• v.26 no.3
• /
• pp.319-329
• /
• 2020

Structural damage to an arch dam is often of major concern and must be evaluated for probable rehabilitation to ensure safe, regular, normal operation. This evaluation is crucial to prevent any catastrophic or failure consequences for the life time of the dam. If specific major damage such as a large crack occurs to the dam body, the assessments will be necessary to determine the current level of safety and predict the resistance of the structure to various future loading such as earthquakes, etc. This study investigates the behavior of an arch dam cracked due to water pressure. Safety factors (SFs), of shear and compressive tractions were calculated at the surfaces of the contraction joints and the cracks. The results indicated that for cracking with an extension depth of half the thickness of the dam body, for both cases of penetration and non-penetration of water load into the cracks, SFs only slightly reduces. However, in case of increasing the depth of crack extension into the entire thickness of the dam body, the friction angle of the cracked surface is crucial; however, if it reduces, the normal loading SFs of stresses and joints tractions reduce significantly.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.21 no.11
• /
• pp.613-620
• /
• 2009

The thermal stresses of a ceramic heat exchanger were analyzed numerically since the ceramic material is good in heat resistance but weak in the thermal stress. The analysis of thermal stress was conducted in the ceramic core with two boundary conditions depending on bolt jointing. The thermal stresses were computed by applying temperature and pressure distributions obtained from the numerical results of conjugate heat transfer to ANSYS WORKRBENCH. When number of bolt joining halls was reduced from $8\times2$ to $4\times2$, the maximum principal stresses decrease by 47.6~50.5% and increase in safety factors by 2.18~2.5 for ultimate tensile strength. Thus, it can be said that bolt joining halls should be minimized in ceramic heat exchanger to be efficient in reducing thermal stress. In addition, the width of particular gas flow passages were revised from 52 mm to 42 mm to reduce maximum thermal stresses since certain passages experienced high thermal stresses. From the revision, safety factors were increased by 13.8~14.1% for the boundary condition of $4\times2$ bolt joining halls. Therefore, it is suggested that thermal stress can be reduced by changing local geometry of a ceramic heat exchanger.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.6
• /
• pp.7-14
• /
• 2011

This paper is related to a roll-type micro-contact printing process. The proper parameters such as coating velocity, inking velocity, printing velocity and printing pressure as well as Ag contents of Ag ink were extracted to perform the fine patterning of Ag electrodes. Additionally we developed a process for PDMS with high uniform thickness. Finally, we obtained the Ag fine electrodes on $4.5cm\;{\times}\;4.5cm$ plastic substrate with the line width of 10 um, thickness less than 300 nm, surface roughness less than 40 nm, and the specific resistance of $2.08\;{\times}\;10^{-5}{\Omega}{\cdot}cm$.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.4
• /
• pp.69-74
• /
• 2019

The influence of measuring fixtures on the measurement of dielectric and piezoelectric properties of PMN-PT single crystal specimens was investigated. As the pressure of the jig pin which applied the AC electrical signal to the sample decreased, the lower resonance resistance was measured and the higher mechanical quality factor was calculated. The mechanical quality factor was 418 when the spring tension of the jig pin was 20grf, and the value of the quality factor was reduced by half when the spring tension was 200grf. The 4-probe fixture method is unsuitable for measuring piezoelectric properties, but it was suitable for the measurement of dielectric loss. In order to accurately evaluate the piezoelectric properties of PMN-PT, it is necessary to lower the spring tension of the jig pin as much as possible.