• Journal of Ocean Engineering and Technology
• /
• v.12 no.3 s.29
• /
• pp.60-67
• /
• 1998

In this study, the J-Resistance Curve and material tearing modulus of SA508-C3 steel, which is one of the used nuclear pressure vessel steel, are measured ar room temperature, $200^{circ}C$ and $300^{circ}C$ according to load ratio analysis and ASTM E813, ASTM E1152, respectively. It is observed that J-R curve and Tmat value decrease as the temperature level increase. Applicability of $T_j$ proposed by Paris et al as instability parameter for ductile material is investigated. It is concluded that results are the $T_j$ parameter may be used as a crack instability parameter.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.569-574
• /
• 2005

The steel retaining wall(s.r.w) are not constructed broadly all over the world. So the method of the analysis and the estimation for the behavior of the s.r.w. the interactive behavior of the frame and the fill material. In this study, the numerical analysis using F.E.M. was made to analize the mutural relation of the frame and the fill material in prior to the s.r.w. model test.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.1005-1008
• /
• 2003

We report a new FCOG (flip chip on glass) technique using solder bumps for display packaging applications. The In and Sn solder bumps of 40 ${\mu}m$ pitches were formed on Si and glass substrate. The In and Sn bumps were bonded at 125 at the pressure of 3 mN/bump. The metallurgical bonding was confirmed using cross-sectional SEM. The contact resistance of the solder joint was 65 $m{\Omega}$ which was much lower than that of the joint made using the conventional ACF bonding technique. We demonstrate that the new COG technique using solder bump to bump direct bonding can be applied to advanced LCDs that lead to require higher quality, better resolution, and lower power consumption.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.642-646
• /
• 1989

We have developed analysis program of discharge chracteristics of KrF laser system with charge transfer type, that studied about deposited energy, nonlinear discharge, and electron number density in the laser tube. With this program, voltagr, current, and deposited energy was calculated 27 KV,32.6 KA,200 MW at total pressure 2 atm and charging voltage 33 KV, respectively. At this condition, circuit parameters are L1=150nH, R1=$0.3{\Omega}$, L2=15nH, R2= $0.3{\Omega}$. In addition, nonlinear discharge resistance and electron number density was calculated ${\infty}{\sim}0.17{\Omega}.1{\times}10^{16}cm^{-3}$, respectively.

• Korean Journal of Health Education and Promotion
• /
• v.13 no.2
• /
• pp.54-68
• /
• 1996

This study aimed at examining the risk factors of smoking behavior among middle school students and preparing school-based smoking prevention program. This study surveyed at February 1995 from 892 students at 3 middle schools in Seoul. The major findings of this study are follows; The proportion of current smoker among students in this study was 3.8%, and the proportion of intentions to smoking was 8.4%. At demographic variables male, pocket money of month was significantly positive association with smoking behavior, but economic status and education status of father were significantly negative association with smoking behavior. Results indicated that social influence variables(peer influence), alcohol, and positive attitudes of smoking were significantly positive association with smoking behavior. So implications for smoking prevention programs may be more effective at risk populations than using general adolescent population. Also ‘School-based smoking prevention programs’ may be learning social pressure resistance skills and giving knowledge and information about negative attitudes about smoking.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.74-77
• /
• 2002

The channel of the superconducting Flux Flow Transistor has been fabricated with plasma etching method using ICP. The ICP conditions were 700 W of ICP power, 150 W of rf chuck power, 5 mTorr of the pressure in chamber and 1:1 of Ar : Cl$_2$, respectively. The channel etched by plasma gas showed superconducting characteristics of over 77 K and superior surface morphology. The critical current of SFFT was altered by varying the external applied current. As the external applied current increased from 0 to 12 mA, the critical current decreased from 28 to 22 mA. Then the obtained r$\sub$m/ values were smaller than 0.1Ω at a bias current of 40 mA. The current gain was about 0.5. Output resistance was below 0.2 Ω.

• Journal of the Korean Ceramic Society
• /
• v.34 no.5
• /
• pp.491-499
• /
• 1997

High flexible lightweight composites containing tobermorite as a main mineral is produced using various amorphous silicates, lime, cement and fibers. Here, Mechanical properties of the composites were studied by observing microstructures of hydrates and fibers. Amorphous silicates having better hydraulicity retarded the crystallization of tobermorite due to better formation of C-S-H gel in water bath curing, but, difficult conversion from C-S-H gel to tobermorite in hydrothermal reaction. In the low molar ratio of CaO/SiO2 (0.67), faster crystalization was observed dued to more impurities such as Al2O3 alkali, resulting in improving mechanical properties due to small crystal size and many contact points. It was identified that a lot of calcium silicate hydates formed at surface of pulps increase bonding strength and the crack-resistance of matrix in the composites, but decrease hardness and compressive strength. The choice of amorpous silicates having better hydraulicity, low CaO/SiO2 adding each fibers bellow about 5% in the raw mixs and lower molding pressure should be needed at improve mechanical properties of composites.

• Journal of the Korean Ceramic Society
• /
• v.26 no.1
• /
• pp.7-12
• /
• 1989

The effects of composition ratios and sintering conditions in Co1-xMgxO ceramics on the sintering characteristics, electrical properties and oxygen sensing characteristics were investigated. In the same sintering conditions, porosity decreased with increase of MgO contents. The relationshiop of temperature and resistance in Co1-xMgxO ceramics showed NTC(negative temperature coefficient) characteristics at the temperature range from $700^{\circ}C$ to 1,10$0^{\circ}C$. In the case of pure CoO, however, the PTC(positive temperature coefficient) characteristics were shown over about 90$0^{\circ}C$. The electrical conductivity of Co1-xMgxO ceramics decreased proportionally with decrease of oxygen partial pressure at the range from 1 to 10-4(atm). Particularly, Co0.5Mg0.5O ceramics showed the highest sensitivity to oxygen gas.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.385-385
• /
• 2010

In this work, we have investigated the etching characteristics of $TiO_2$ and selectivity of $TiO_2$ over $SiO_2$ thin films as resistance in ReRAM using the inductively coupled plasma. The etch rate and selectivity were measured by varying the $BCl_3$ addition into Ar plasma. The maximum etchrate was obtained at 110.1nm/min at $BCl_3$/Ar=5sccm/10sccm, 500W for RFpower, -100v for DC-bias voltage, and 2Pa for the process pressure. The etched $TiO_2$ surface was investigated with X-ray photo electron spectroscopy. We explained the etching mechanism in two etch mechanisms, physiclas puttering and chemical reaction.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.10a
• /
• pp.65-67
• /
• 2002

Resin Transfer Molding(RTM) is increasingly used for producing fiber reinforced polymer composites, the resin has to flow a long distance to impregnate the dry fibers. The measure for the resistance of the fiber preform to the resin flow is the permeability of the fiber preform. Permeability is a key issue in the design of molds and processes and in flow modeling. In this study, permeability measurement for braided preform is presented and compared with the permeability calculated numerically. Experimental techniques being used to measure the permeability are also discussed. Measurement is conducted in radial flow test under constant pressure.