• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2009년도 춘계학술대회 논문집
• /
• pp.665-666
• /
• 2009

• 한국군사과학기술학회지
• /
• 제16권6호
• /
• pp.847-856
• /
• 2013

In this study, thermal performance of recuperators with plain and offset strip fins is investigated to enhance the thermal efficiency of a micro gas turbine. Thermal cycle analysis is conducted to determine major design parameters of a single-pass counterflow recuperator. In order to evaluate the performance of the recuperator, the effectiveness and the pressure drop in the recuperators are chosen as the objective function and the design constraint, respectively. The optimized geometries for internal structure of the recuperators with plain and offset strip fins are obtained with varying the fin spacing and height. From the result, the recuperator with offset strip fins has better thermal performance when the fin spacing, s, is smaller than 1.45mm and the thermal performance of the recuperator with plain rectangular fins is higher than that with offset strip fins in the region of $s{\geq}1.45mm$. In addition, it is found that the entrance region effect and the longitudinal wall heat conduction effect should be taken into account for accurately predicting the thermal performance of the recuperators with both plain and offset strip fins.

• 한국정밀공학회지
• /
• 제19권7호
• /
• pp.147-153
• /
• 2002

The exhaust muffler is designed to reduce the engine noise with the minimum back pressure. It is composed of several elements, and we chose the five types of muffler elements : expansion, extended, offset, reversal, and perforated type. These elements are modeled with I-DEAS, and the transmission loss is analyzed with SYSNOISE, and the back pressure with STAR-CD. We verified the numerical results of transmission loss and pressure loss by experiments for the case of extended muffler. We find a database with the numerical results, which can be used in the design of exhaust muffler in the field.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 추계학술대회 논문집 학회본부
• /
• pp.342-344
• /
• 1995

Using piezoresistive effects of single-crystal and poly-crystalline silicon, pressure sensors of the same pattern were fabricated for comparison of temperature characteristics. Optimum size and aspect ratio of rectangular sensor diaphragm were calculated by FEM. For polsilicon pressure sensor, polysilicon resistors of Wheatstone bridge were deposited by LPCVD to be used in a wide' temperature range. Polysilicon pressure sensors showed more stable temperature characteristics than single-crysta1 silicon in the range of $-20\sim125[^{\circ}C]$. To get low TCO (Temperature Coefficient of Offset), below $\pm$3 [${\mu}V/V/^{\circ}C$], it is needed for each TCR of piezoresistors to have a deviation within $\pm25[ppm/^{\circ}C]$ less than $\pm500[ppm/^{\circ}C]$ of resistors for polysilicon pressure sensor can result in low TCS(Temperature Coefficient of Sensitivity) of -0.1[%FS/$^{\circ}C$].

• 설비공학논문집
• /
• 제13권8호
• /
• pp.730-738
• /
• 2001

This work discusses the pressure droop, heat and mass transfer of the finned-tube heat exchangers having 7 mm tubes and offset strips in dehumidifying applications. It focuses on the fin material saving and the reduction of pressure drop. The experiment was conducted using three times scaled-up models to simulate the performance of the prototype. Eight kinds of fins having different strips and S shape edges were tested. the area density of the strip was a major factor and its shape and the location were secondary factors on the pressure drop, the heat and mass transfer. The reduced-area fin can almost equal the non-reduced fin in the aspect of heat and mass transfer. The strip fins proposed in the present work can considerably reduce both the pressure drop and the fin material for similar thermal load.

• 센서학회지
• /
• 제1권2호
• /
• pp.131-145
• /
• 1992

본 논문은 SOI트랜스듀서 및 회로를 위해, Si 직접접합과 M-C국부연마법에 의한 박막SOI구조의 형성 공정을 기술한다. 또한, 이러한 박막SOI의 전기적 및 압저항효과 특성들을 SOI MOSFET와 cantilever빔으로 각각 조사했으며, bulk Si에 상당한다는 것이 확인되었다. 한편, SOI구조를 이용한 두 종류의 압력트랜스듀서를 제작 및 평가했다. SOI구조의 절연층을 압저항의 유전체분리층으로 이용한 압력트랜스듀서의 경우, $-20^{\circ}C$에서 $350^{\circ}C$의 온도범위에 있어서 감도 및 offset전압의 변화는 자각 -0.2% 및 +0.15%이하였다. 한편, 절연층을 etch-stop막으로 이용한 압력트랜스듀서에 있어서의 감도변화를 ${\pm}2.3%$의 표준편차 이내로 제어할 수 있다. 이러한 결과들로부터 개발된 SDB공정으로 제작된 SOI구조는 집적화마이크로트랜스듀서 및 회로개발에 많은 장점을 제공할 것이다.

• 설비공학논문집
• /
• 제16권10호
• /
• pp.977-983
• /
• 2004

An experimental study on saturated flow boiling heat transfer of R113 was peformed in a vertical narrow rectangular channel with offset strip fins. Two-phase pressure gradients and boiling heat transfer coefficients in an electrically heated test section were measured in the range of quality $0{\sim}0.6$, mass flux $17{\sim}43kg/m^{2}s$, and heat flux of $500{\sim}3,000W/m^2$ Two-phase friction multipliers were determined as a function of Lockhart-Martinelli parameter. Local boiling heat transfer coefficients were analysed in terms of mass flux, heat flux and local vapor quality. Correlation for boiling heat transfer coefficients was proposed, which was in good agreement with experimental data.

• Journal of Mechanical Science and Technology
• /
• 제17권6호
• /
• pp.870-878
• /
• 2003

The scale is removed from the strip by high pressure hydraulic descaling at the FSB (Finishing Scale Breaker). Recently, the spray height of nozzle has a trend to be shorter for the purpose of increasing the impact pressure by the high pressure water jet. Here, the nozzle intervals should be decided after considering the impact pressure and the temperature distribution on the strip. In other words, the minimum of impact pressure at the overlap of spray influences the surface grade of the strip due to scale and the overlap distance of the spray affects the temperature variation in the direction of the width of strip. In the present study, the impact pressure of the high pressure water jet is measured by the hydraulic descaling system and calculated with regard to the lead angle of 15$^{\circ}$ and the offset angle of 15$^{\circ}$, and then the temperature distribution and the temperature variation are calculated at the overlap distances of 0 mm, 10 mm, 20 mm, and 30 mm, respectively. The method of setting nozzle intervals is shown by utilizing these results.

• 대한기계학회논문집B
• /
• 제24권2호
• /
• pp.224-232
• /
• 2000

Four turbulent $k-{\varepsilon}$ models (i.e., standard model, modified models with streamline curvature modification and/or preferential dissipation modification) are applied in order to analyze the turbulent flow of wall-attaching offset jet. For numerical convergence, this paper develops a method of slowly increasing the convective effect induced by skew-velocity in skew-upwind scheme (hereafter called Partial Skewupwind Scheme). Even though the method was simple, it was efficient in view of convergent speed, computer memory storage, programming, etc. The numerical results of all models show good prediction in first order calculations (i.e., reattachment length, mean velocity, pressure), while they show some deviations in ·second order (i.e., kinetic energy and its dissipation rate). Like the previous results obtained by upwind scheme, the streamline curvature modification results in better prediction, while the preferential dissipation modification does not.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2005년도 Proceedings of ISRS 2005
• /
• pp.616-619
• /
• 2005

CALNAL team of Korea Aerospace Research Institute(KARI) performed field campaigns for absolute radiometric calibration of 1m satellite image on Daejeon and the cal/val site of Goheung. The satellite image have spatial resolution of 1m in panchromatic spectral band of 450-900nm. The performed cal/val method is the reflectance-based of vicarious calibration methods. We collected ground-based and meteology data such as temperature, surface pressure and reflectance of targets, and radiosonde data used only to test in Goheung. Data collected on each field served as input to radiative transfer codes to generate a top-of-atmosphere(TOA) radiance estimate. Derived TOA is compared with DN of overpass satellite to calculate calibration coefficient of gain and offset.