• 설비공학논문집
• /
• 제27권5호
• /
• pp.263-268
• /
• 2015

In this study, the performance of an ejector in the refrigeration cycle was experimentally studied using R600a. The performance of the ejector is analyzed according to the inlet pressure and nozzle position. The increase in the primary nozzle pressure decreased the pressure difference across the ejector. In the low entrainment region, the increased suction flow pressure led to an increase in the pressure difference. In the high entrainment region, the pressure difference was inversely proportional to the suction pressure. The effects of nozzle position ($L_n$) were also analyzed and for $L_n<0$, the decreased suction chamber volume led to a large pressure drop with the small increase in the suction mass flow rate. For $L_n>0$, the increased $L_n$ disturbed the primary nozzle flow and thus an increase in the primary nozzle flow increased the pressure lifting effect. In contrast, the increased suction mass flow rate decreased the pressure difference. When the nozzle outlet was located at the mixing part entrance ($L_n=0$), the ejector showed the highest pressure lifting effect.

• 대한조선학회논문집
• /
• 제33권1호
• /
• pp.19-26
• /
• 1996

프로펠러에 의한 선체변동압력을 추정하기 위해 3개의 선체에 7개의 프로펠러를 장착하여 실험과 계산치를 비교하였다. 변동압력의 계측은 KRISO의 공동터널에서 평판에 대하여 수행하였으며, 수치계산은 양력면 이론과 패널법을 사용한 수치프로그램(X-ForShip)을 사용하였다. 평판에 대한 실험값을 복잡한 선미형상에 적용하기 위하여 강체경계율(SBF)이 수정계수로 결정되었다. 실선 변동압력의 예측과 실험치의 수정을 위하여 복잡한 선미형상에서의 변동 압력을 계산하였다. 계산치와 수정된 실험치와의 좋은 일치를 보였으며, 수성계수로써 약 0.65-0.7의 값이 결정되었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.860-863
• /
• 1992

In this paper, we investigate $\pi$-A isotherms of biological lipid layer such as cholesterol and phosphatidyl choline to study a gas sensor characteristics which response only to specific materials. And, we also deposit it on the surface of quartz crystal by vertical dipping method and horizontal lifting method. Then, we evaluate the deposition status of cholesterol and phosphatidyl choline LB film using AT-cut quartz crystal. We obtain the following results: (1) Cholesterol's solid surface pressure is about 20$\sim$40(dyne/cm) and limiting area is about 50${\AA}^2$/molecule. And, phosphatidyl choline's surface pressure is about 25$\sim$40(dyne/cm) and limiting area is about 20 ${\AA}^2$/molecule. (2) When LB films are deposited, the deposition ratio is coincident with the frequency shift. Therefore, we can evaluate the deposition status of LB film. (3) For cholesterol, Y type LB films are deposited up to 15 layers by vertical dipping method. (4) For phosphatidyl choline, X typo LB films are deposited to 15 layers by horizontal lifting method. But, in case of vertical dipping method, the deposition status is not good.

• 한국정밀공학회지
• /
• 제25권2호
• /
• pp.49-56
• /
• 2008

In order to reduce energy consumption, secondary controlled system has been applied to many types of equipments. In lifting equipments or press machines using hydraulic cylinder, a hydraulic transformer is used as a control component instead of a valve for motion control and a component for recovering potential energy of load. The transformer is a combination of a variable displacement pump/motor as a secondary controlled element and a fixed displacement pump/motor. In this paper the effect of transformer is studied. Multiple closed loop controllers with displacement feedback of variable pump/motor, speed feedback and position feedback of cylinder are used. The efficiency and energy consumption when cylinder is driven up and down is calculated by simulation. Simulation results show that considerable energy saving is achieved by choosing load ratio, circuit type and supply pressure.

• 드라이브 ㆍ 컨트롤
• /
• 제12권4호
• /
• pp.35-40
• /
• 2015

A gas spring provides support force for lifting, positioning, lowering, and counterbalancing weights. It offers a wide range of reaction force with a flat force characteristic, simple mounting, compact size, speed controlled damping, and cushioned end motion. The most common usage is as a support on a horizontally hinged automotive tail gate. However, its versatility and ease of use has been applied in many other industrial applications ranging from office equipment to off-road vehicles. The cylinder of a gas spring is filled with compressed nitrogen gas, which is applied with equal pressure on both sides of the piston. The surface area of the rod side of the piston is smaller than the opposite side, producing a pushing force. The magnitude of the reaction force is determined by the cross-sectional area of the piston rod and the internal pressure inside the cylinder. The reaction force is influenced by many design parameters such as initial chamber volume, diameter ratio, etc. In this paper, we investigated the reaction force characteristics and carried out parameter sensitivity analysis for the design parameters of a gas spring.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1075-1080
• /
• 2007

In order to reduce energy consumption, secondary controlled system has been applied to many types of equipments. In lifting equipments or press machines using hydraulic cylinder, a hydraulic transformer is used as a control component instead of a valve for motion control and a component for recovering potential energy of load. The transformer is a combination of a variable displacement pump/motor as a secondary controlled element and a fixed displacement pump/motor. In this paper the effect of transformer is studied. Multiple closed loop controllers with displacement feedback of variable pump/motor, speed feedback and position feedback of cylinder are used. The efficiency and energy consumption when cylinder is driven up and down is calculated by simulation. Simulation results show that considerable energy saving is achieved by choosing load ratio, circuit type and supply pressure.

• International Journal of Fluid Machinery and Systems
• /
• 제4권4호
• /
• pp.367-374
• /
• 2011

Water hammer pumps can effectively use the water hammer phenomenon in long-distance pipeline networks that include pumps and allow fluid transport without drive sources, such as electric motors. The results of experiments that examined the effect of the geometric form of water hammer pumps by considering their major dimensions have been reported. In addition, a paper has also been published analyzing the water hammer phenomenon numerically by using the characteristic curve method for comparison with experimental results. However, these conventional studies have not fully evaluated the pump performance in terms of pump head and flow rate, common measures indicating the performance of pumps. Therefore, as a first stage for the understanding of water hammer pump performance in comparison with the characteristics of typical turbo pumps, the previous paper experimentally examined how the hydrodynamic characteristics were affected by the inner diameter ratio of the drive and lifting pipes, the form of the air chamber, and the angle of the drive pipe. To understand the behavior of the components attached to the valve chamber and the air chamber that affects the performance of water hammer pumps, the previous study also determined the relationship between the water hammer pump performance and temporal changes in valve chamber and air chamber pressures according to the air chamber capacity. For the geometry of components attached to the drain valve, which is another major component of water hammer pumps, this study experimentally examines how the water hammer pump performance is affected by the length of the spring and the angle of the drain pipe.

• 한국항공우주학회지
• /
• 제41권8호
• /
• pp.639-648
• /
• 2013

본 논문은 부게넘 및 태안 IGCC플랜트의 연료를 대상으로 석탄으로부터 생성된 합성가스의 NOx/CO배출 특성, 온도특성, 화염의 구조에 대해 기술하였다. GE7EA 모사 가스터빈 연소기를 대상으로 상압 고온 연소시험을 수행하여 입열량 및 질소희석에 따른 연소특성을 관찰하였다. 입열량이 감소하고, 희석제량이 증가할 때 단열화염온도의 감소로 NOx가 감소하였고, 저부하에서는 희석량이 증가할수록 불완전 연소로 인해 CO가 증가하였다. 이러한 NOx 감소 및 CO발생은 각각 $1500^{\circ}C$ 와 $1250^{\circ}C$의 특정 화염온도에서 관찰되었다. 또한 질소 희석이 증가할수록 단열화염온도 및 연소기 라이너의 온도가 감소했고, 화염 부상과 같은 화염구조의 변화로 인해 특이점이 관찰되었다. 본 연구결과를 통해 질소희석이 NOx/CO배출 및 온도, 화염구조에 미치는 영향이 검토되었으며, 시험 데이터는 향후 태안 IGCC 플랜트의 운전시 최적 조건 선정을 위한 기초자료로 활용될 예정이다.

• Tuberculosis and Respiratory Diseases
• /
• 제45권1호
• /
• pp.140-152
• /
• 1998

배 경: 호흡부전의 치료에 있어 환자 체위를 prone position으로 하는 시도는 20년 전부터 보고되어 왔으며 폐산소화 및 심박출량 향상에 효과가 있다는 것이 알려져 있다. Prone position시 폐산소화의 호전은 임상 및 동물 실험에서 단락 감소에 의한 것으로 알려져 있으며 그 중요 기전은 supine position에 비해 prone position때 중력 의존부 폐의 늑막압이 더 작아 폐포 개방압이 줄어들기 때문인 바 저자 등은 prone position이 폐산소화에 미치는 효과는 supine position에서 사용한 PEEP의 폐포 고비 개방압과의 관계에 따라 달라질 것으로 추정하였다. Prone position에서의 심박출량 증가에 대하여는 양압환기시 발생하는 cardiac fossa lifting 현상이 prone position에 의해 완화될 수 있다는 주장이 제기된 바 있어 prone position이 또한 supine position에서 PEEP에 의해 초래된 심박출량 저하를 완화시킬 수 있는지를 잡종견 급성 폐손상 모델을 통해 알아보고자 하였다. 방 법 : 잡종견 7 마리 ($20.0{\pm}3.9$ kg)를 정맥 마취 후 기관내관을 삽관하고 인공호흡기를 Vt 15 ml/kg, f 20/min, I : E=1 : 3, pause 10%, PEEP 0 cm $H_2O$, $F_1O_2$ 1.0으로 설정하였다. 혈압, 분당맥박수, 폐동맥쐐기압, 심박출량 등의 측정과 동맥혈가스분석을 위해 서혜동맥과 폐동맥 천자술을 시행하였다. 대조기에 supine position 및 prone position 30분에 각각 호흡 지표 ($PaO_2/F_1O_2$[P/F], 총호흡기계탄성 [Cst]와 supine position, prone position 5분 및 prone position 30분에 혈류역학적 지표(평균동맥압, 분당 맥박수, 심박출량, 박출용적)을 측정하고 섭씨 38도의 생리식염수 (30~50 ml/kg)를 기관내관을 통하여 주입하여 급성 폐손상을 유도한 뒤 constant flow 법에 의해 inflection point(Pflex)를 측정하였다. 급성 폐손상에서의 supine position과 prone position실험은 Pflex보다 2 cm $H_2O$ 낮은 PEEP(Low PEEP)과 2 cm $H_2O$ 높은 PEEP (Optimal PEEP)에서 순차적으로 시행하고 각각 통일 시간대에 상기 지표들을 측정하였으며 Optimal PEEP 실험 마지막에 다시 supin position으로 체위를 바꾸고 5분 뒤 혈류역학적 지표들을 측정하였다. 결 과: 1. Prone position 시행시 Low PEEP 및 Optimal PEEP에서의 호흡 효과의 차이 Low PEEP하에서 P/F 비는 supine position에서 $195{\pm}112$ mm Hg, prone position 30분에서 $400{\pm}33$ mm Hg였고 (p<0.001) Optimal PEEP하에서 P/F 비는 supine position에서 $466{\pm}63$ mm Hg, prone position 30분에서 $499{\pm}63$ mm Hg였다 (p=0.016). Prone position에 의한 P/F 비 싱승량은 Low PEEP하에서 $205{\pm}90$ mm Hg로 Optimal PEEP($33{\pm}33$ mm Hg) 하에서 보다 유의하게 높았다(각각 p<0.05). 2. Prone position의 혈류역학적 효과 Low PEEP하에서 심박출량은 supine position($3.0{\pm}0.7$ L/min) 과 비교하여 prone position 5분 $3.3{\pm}0.7$ L/min(p=0.0180)로 증가하였고 prone position 30분 $3.7{\pm}0.8$ L/min(p=0.0630)로 차이가 없었다. 분당맥박수는 각각 $141{\pm}22\;min^{-1}$, $141{\pm}22\;min^{-1}$(p=0.8658) 및 $176{\pm}28\;min^{-1}$(p=0.0280)이었고 폐동맥쐐기압은 차이가 없었다. Optimal PEEP하에서 평균동맥압은 각각 $87{\pm}19$ mm Hg, $107{\pm}18$ mm Hg(p=0.0180) 및 $108{\pm}16$ mm Hg(p=0.0180), 심박출량은 각각 $2.4{\pm}0.5$ L/min, $3.3{\pm}0.6$ L/min(p=0.0180) 및 $3.6{\pm}0.7$ L/min(p=0.0180), 그리고 박출용적은 각각 $14{\pm}2$ml, $20{\pm}2$ ml(p=0.0180) 및 $21{\pm}2$ ml(p=0.0180)였다. 분당맥박수는 체위 변경에 따른 차이가 없었고 폐동맥쐐기압은 각각 $10.1{\pm}2.4$ mm Hg, $9.1{\pm}2.7$ mm Hg(p=0.0180) 및 $9.0{\pm}3.1$ mm Hg(p=0.0679) 이었다. Optimal PEEP하 prone position에서 다시 supine position으로 체위를 바꾸고 5분 후 평균동맥압은 $92{\pm}23$ mm Hg, 심박출량은 $2.4{\pm}0.5$ L/min, 그리고 박출용적은 $14{\pm}1$ ml로 모두 감소하였다(모두 p<0.05). 결 론 : 잡종견 급성폐손상 모델에서 prone position은 비교적 낮은 수준 PEEP의 폐산소화 호전 효과를 중대시켰고, 비교적 놓은 수준 PEEP에 의한 심박출량 저하를 완화시켰다. 이러한 결과들은 심박출량을 유지하면서 폐산소화를 호전시키고자 하는 ARDS 환자에서의 기계환기의 목표를 달성하는데 있어 prone position이 supine position보다 유리하다는 것을 시사한다.