• 한국유체기계학회 논문집
• /
• 제8권4호
• /
• pp.20-26
• /
• 2005

When the pumps are started or stopped for the operation or tripped due to the power failure, the hydraulic transients occur as a result of the sudden change in velocity. The field tests on the waterhammer were carried out for Pangyo booster pumping station in which had six booster pumps and two in-line pumps with the motor of output 1,700 kW, respectively. The booster pumping station was equipped with the pump control valve as the main surge suppression device, and the surge relief valve as auxiliary one. But the pump control valve had not early controlled in the planned closing mode, the slamming occurred to the valve of which abruptly closed during the large reverse flow. Because the positive pressure wave caused by the pump failure was superposed on the slam surge, the upsurge increased so extremely that the pump control valve was damaged. After the air chambers were additionally installed in the booster pumping station, it was preyed that the water supply system acquire the safety and reliability on the pressure surge.

• 드라이브 ㆍ 컨트롤
• /
• 제18권2호
• /
• pp.1-8
• /
• 2021

In this work, a circuit with a hydraulic power unit is formulated as a means of predicting the behavior of the prefill valve in the future. The behavior of the prefill valve can be examined by the measurements of the configured power unit, and the performance is determined by using hydraulic pumps, relief valves, and hydraulic hoses that make up the power unit. In particular, pressure/flow pulsation generated by hydraulic pumps can cause instability in the prefill valve and cause noise-induced degradation of the overall performance and reliability of the hydraulic system containing the prefill valve. Therefore, to study the behavior and performance of the prefill valve in a relatively accurate manner, the prediction of the characteristics of the hydraulic power unit driving the prefill valve is very important. In this study, the pulsation characteristics of the hydraulic pump were analyzed to theoretically demonstrate its relationship with different settings of the power unit, such as relief valve pressure settings and the presence/absence of the hose.

• 한국추진공학회지
• /
• 제15권6호
• /
• pp.70-77
• /
• 2011

우주발사체의 액체추진공급시스템에 사용되는 벤트/릴리프 밸브는 안전 밸브의 조합체로 극저온의 산화제를 주입할 때와 보관할 때 기화된 산소기체를 배출시킨다. 또한 비행 중에 추진제 탱크의 얼리지 압력을 안정적으로 유지하는 역할을 한다. 밸브의 동특성 및 유공압 작동특성을 알아보기 위해서 벤트/릴리프 밸브의 설계검증을 위해 AMESim을 이용해서 벤트/릴리프 밸브의 시뮬레이션 모델을 구성하였다. AMESim 밸브 모델을 검증하기 위해 밸브의 개폐 압력, 개폐작동시간을 수학적 계산 결과와 비교하였다. 또한 FLUENT 상용코드를 이용하여 내부유동 해석 결과를 반영하여 모델의 정확도를 높였다. 밸브 모델을 이용하여 설계인자에 대한 검증 및 작동성능을 분석하였다. 이 연구는 한국형 발사체에 사용되는 벤트/릴리프 밸브의 다양한 작동 요구조건에 대한 개발 효율성을 높일 수 있는 참고 가이드로 적용될 것으로 판단된다.

• Nuclear Engineering and Technology
• /
• 제36권4호
• /
• pp.285-294
• /
• 2004

Pressure wave propagation in the discharge piping with a sparger submerged in a water pool, following the opening of a safety relief valve, is analyzed. To predict the pressure transient behavior, a RELAP5/MOD3 code is used. The applicability of the RELAP5 code and the adequacy of the present modeling scheme are confirmed by simulating the applicable experiment on a water hammer with voiding. As a base case, the modeling scheme was used to calculate the wave propagation inside a vertical pipe with sparger holes and submerged within a water pool. In addition, the effects on wave propagation of geometric factors, such as the loss coefficient, the pipe configuration, and the subdivision of sparger pipe, are investigated. The effects of inflow conditions, such as water slug inflow and the slow opening of a safety relief valve are also examined.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.741-747
• /
• 2010

발사체의 추진공급시스템에 사용되는 벤트/릴리프밸브는 안전밸브의 조합체로 극저온의 산화제를 주입할 때와 비행 중에 기화된 산소기체를 배출시킨다. 벤트/릴리프밸브의 설계검증을 위해 AMESim과 FLUENT 상용코드를 이용하여 밸브모델을 구성하였다. AMESim 밸브모델을 검증하기 위해 밸브의 개폐압력, 개폐작동시간을 수학적 계산결과와 비교하였고 내부유동해석 결과를 반영하여 모델의 정확도를 높였다. 본 연구에서는 설계인자를 검증 및 작동성능을 분석하였다. 이 결과는 한국형 발사체에 사용되는 다양한 규격의 벤트/릴리프밸브 개발과정의 효율성을 높일 수 있을 것으로 판단된다.

• 한국생산제조학회지
• /
• 제22권1호
• /
• pp.1-7
• /
• 2013

Pneumatic cylinders are widely used to actuators in automatic equipments because they are relatively inexpensive, simple to install and maintain, offer robust design and operation, are available in a wide range of standard sizes and design alternatives. This paper presents a comparative study among the dynamic characteristics of meter-out and meter-in speed control of pneumatic cushion cylinders with a relief valve type cushion mechanism. Because of the nonlinear differential equations and a requirement for simultaneous iterative solution in a mathematical model of a double acting pneumatic cushion cylinder, a computer simulation is carried out to investigate pressure, temperature, mass flow rate in cushion chamber and displacement and velocity time histories of piston under various operating conditions. It is found that the piston velocity and pressure response in meter-in speed control are more oscillatory than with meter-out those when pneumatic cushion cylinders are driven at a high-speed. In meter-out speed control, the effective area of the flow control valve is larger than that of meter-in, and the supply pressure has to be much higher than the pressure required to move the load because it has also to overcome the back pressure in cushion chamber.

• 대한기계학회논문집
• /
• 제3권3호
• /
• pp.104-115
• /
• 1979

The dynamic chracteristics of a two stage relief valve is studied theoretically and experimentally. The equations of motion of spools are derived and solved by digital compter simulation to find the stiability criteria.It is shown that the area of main spool head gives damping effect to the system and that the flow pressure-coefficient of the orifice in main spool is one of the most important parameters to determine stability and response. The experimental resuls are in good atreement with the theoretical results.

• 한국자동차공학회논문집
• /
• 제18권3호
• /
• pp.95-103
• /
• 2010

This paper presents a simulation model of a double-acting high-speed pneumatic cylinder with a relief valve type cushion mechanism. The model predicts piston motion, mass flow rate, pressure and temperature time histories of cushion chamber. Of interest here is to investigate the cushioning effect of varying the piston and piston-rod diameter, cushion ring diameter and length, and stoke in cushion mechanism. As a result, this cushion mechanism is found to be adequate under high-speed driving of pneumatic cylinders. The simulation model proposed here will be very useful to analyze the dynamic characteristics and to improve or design the better cushion mechanism in high-speed pneumatic cushion cylinders.

• 드라이브 ㆍ 컨트롤
• /
• 제18권3호
• /
• pp.8-15
• /
• 2021

A rear axle steering (RAS) system is attached to the rear of medium and large commercial vehicles that transport large cargo. The existing RAS systems are driven by electro-hydraulic actuator (EHA), and most commercialized EHAs consist of electric motors, hydraulic pumps, relief valves, prefill valves and cylinders. The prefill valve required for such EHAs is a type of check valve with extremely low cracking pressure that should not allow RAS to have noise or vibration, and the prefill valve prevents system negative pressure as well as unstable operation. Most papers on this topic rely on experiments to predict valve performance, and theoretically detailed modeling of valves or pipelines is performed, but it is very rare to evaluate hydraulic vibration characteristics by analysing everything from hydraulic pumps to valves comprehensively. In this study, we proposed an experimental circuit that can predict the performance of the prefill valve. The study also analysed the pressure-flow pulsation that is transmitted to the valve through the pipeline, and how the transmitted pressure-flow pulsation affects the valve vibration.

• 한국생산제조학회지
• /
• 제8권2호
• /
• pp.35-43
• /
• 1999

The paper describes an approach for measuring delivery flow ripple generated by oil hydraulic axial piston pumps. In order to reduce pressure ripple which cause to undesirable noise. vibration and fatigue in hydraulic systems it is indispensible measure a delivery flow ripple from pumps. Since the flow ripple measurement of flow pumps is independent of the dynamic characteristics of the connected hydraulic circuit the measurement of flow ripple is most suitable for pump fluid-borne noise rating. The measurement of flow ripple with high frequencies from axial piston pumps is made by applying the remote instantaneous flow rate measurement method which is based on the dynamic characteristics between pressure and flow rate in hydraulic pipeline. The measured flow ripple waveforms are influenced by the configuration of V-shaped triangular relief groove in the valve plate. It can be seen that the appropriate relief groove in valve plate reduces the pressure and flow ripple amplitude and frequency spectrum for high harmonics.