• 설비공학논문집
• /
• 제11권2호
• /
• pp.215-223
• /
• 1999

Evaporation heat transfer coefficient and pressure loss were measured for three different micro-fin tubes and a smooth tube. The experiments were carried out with R-22 over a wide range of vapor Quality, mass velocity and heat flux. Heat transfer coefficient of the tube with slightly modified fin shape was found to be higher than that of the commercial reference tube by 60%. The improvement of heat transfer has been achieved without noticeable increase of pressure loss. Heat transfer coefficient was increased with increasing quality, refrigerant mass flux, and heat flux. However, the effect of refrigerant mass flux and heat flux was not great. Heat transfer coefficient at bottom was lower than that at top of the tube in low quality region, which suggested the existence of stratification in the micro-fin tube. Pressure drop was linearly increased with increasing refrigerant quality and was proportional to about square of mass flux.

• 한국항공우주학회지
• /
• 제47권11호
• /
• pp.779-786
• /
• 2019

본 연구에서 챔퍼가 적용된 타공판의 압력 강하특성에 대한 연구를 진행하였다. 타공판 홀의 입구와 출구에 각각 챔퍼를 적용하였다. 타공판의 패턴이 압력 강하특성에 미치는 영향에 대하여 관찰하였다. 타공판 홀의 입구와 출구에 챔퍼 각도를 변경해 가며 압력 강하 특성을 비교하였다. 레이놀즈 수에 따른 강하특성을 확인하였다. 타공판 홀 입구에 적용된 챔퍼의 각도가 증가함에 따라 압력강하계수가 감소하였지만 특정 각도 이후에서 압력강하계수가 증가하는 것을 확인하였다. 타공판홀 출구에 적용된 챔퍼 형상의 경우 특정 각도와는 상관없이 압력 강하계수가 증가하였다. 동일한 개공률의 타공판에서 삼각 및 사각 패턴에 따른 압력 강하특성은 동일하였다. 본 연구에서 설정한 레이놀즈 수 범위 내에서 압력 강하특성에 대한 레이놀즈 수의 영향은 없는 것으로 확인하였다.

• 대한기계학회논문집B
• /
• 제20권4호
• /
• pp.1501-1509
• /
• 1996

Differential pressure devices such as an orifice and Venturi are widely used in the measurement of flow rate of fluid mainly due to cost effectiveness and easy installation. In the current study, the viscoelastic effect on discharge and loss coefficients of those flow meters were investigated experimentally. Aqueous solutions of Polyacrylamide (200, 500, and 800 ppm) as viscoelastic fluids were used. Discharge coefficient of an orifice for viscoelastic fluids increased significantly up to approximately 15-20% when compared with that for water, while loss coefficient decreased up to 10-25% depending on the diameter ratio, .betha.. Also, pressure recovery for viscoelastic fluids was extended much longer than that for water. On the other hand, discharge and loss coefficients of Venturi for viscoelastic fluids were found to be strongly dependent on the Reynolds number. In both flow meters, the concentration effect for discharge and loss coefficients was not observed at more over than 200 ppm of aqueous solution. Conclusively, orifice and Venturi flow meters should be calibrated very carefully in the flow rate measurement for viscoelastic fluids.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 춘계학술대회 논문집
• /
• pp.295-298
• /
• 2009

Bent duct 는 손실을 가중시키고, 효율을 저하시킨다. 지금까지 bent duct에 대한 많은 연구가 진행되었지만, 입구와 출구가 같은 형상에 대해서 연구가 되어왔다. 이번 연구에서는 입구는 환형이지만, 출구는 원형을 가진 bent duct에 대해서 진행되었다. 입구 속도 54 m/s, 레이놀즈수 238,000에서 수행된 이번 연구에서는 bent duct 바깥에 태핑홀을 배치하여 정압분포를 확인하고, 입구와 출구에서 5공 프로브로 유동을 측정하여 스트림 방향 속도 프로파일과 전압 손실 계수를 얻었다. 본 연구에서는 전압 손실 계수, 0.243를 얻었다.

• 한국수소및신에너지학회논문집
• /
• 제19권5호
• /
• pp.367-376
• /
• 2008

To obtain the data of the pressure loss and differential pressure at the inside of the stack that was composed of 126 cells with 7,500 cm2 electrode area, 75kW molten carbonate fuel cell system has been operated. Computational fluid dynamics was applied to estimate reactions and thermal fluid behavior inside of the stack that was adopted with internal manifold type separator. The pressure loss coefficient K showed 72.29 to 84.01 in anode and 6.34 to 8.75 in cathode at low part of cells at the inside of 75 kW MCFC stack respectively. Meanwhile, the pressure loss coefficient of the higher part of cells at the interior of the stack showed 15.36 and 56.44 in anode and cathode respectively. These results mean that there is no big total pressure difference between anode and cathode at the inner part of 75 kW MCFC stack. This result will be reflected in 250kW MCFC system design.

• 공업화학
• /
• 제21권3호
• /
• pp.258-264
• /
• 2010

대형 선박과 발전소 및 화학 공장 등을 구성하는 배관 및 계통은 다양한 구성요소들로 이루어져 있다. 밴드, 티, 급격 확대, 급격축소, 오리피스와 같은 이러한 구성요소들은 시스템 전체의 압력강하를 유발한다. 집중변수모델을 사용하여 구성요소들에 의한 압력손실은 계산할 시에는 압력손실계수인 k-factor가 제공되어야 한다. 일반적으로 많은 공학 분야에서 k-factor의 계산에 Idelchik 모델이 사용되어 왔다. 본 연구에서는 전산유체역학 해석을 통하여 압력손실계수를 계산하고 그 결과를 Idelchik이 제안한 압력손실계수와 비교하였다. 이는 복잡한 유동영역의 압력손실계수 계산에 전산유체역학 코드의 활용성을 검증하기 위함이다. 해석결과, 레이놀즈 응력 모델이 압력손실계수를 가장 잘 예측하고 있다. 전산유체역학을 통한 압력손실계수 평가는 사용된 난류모델에 영향을 받지만 압력손실계수를 잘 예측하고 있으므로 압력손실 계산에 전산유체역학 코드를 사용하는 것은 타당하다고 판단된다.

• 수산해양기술연구
• /
• 제28권2호
• /
• pp.157-163
• /
• 1992

In this paper, the relationship between static pressure recovery and turbulent energy was presented in case of swirling flows into a conical diffuser. The distributions of turbulent energy in a diffuser sectional area were measured by a hot wire anemometer. The following conclusion can be drawn from the experiment. Diffuser loss is constituted by a dynamic pressure loss and total pressure loss. The static pressure recovery depends strongly on the total pressure loss. The static pressure recovery depends strongly on the total pressure loss, and the turbulent energy varies inversely as the static pressure recovery coefficient.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권6호
• /
• pp.923-930
• /
• 2008

The butterfly valve is widely used in the industrial field as an on-off or a flow control valve. When the butterfly valve is used as a flow control valve. cavitation sometimes occurs in the range of high flow rate because of the small valve opening. Therefore. the pressure loss and the cavitation characteristics are investigated by use of a commercial CFD code. The results show that the possibility of cavitation occurrence in the cryogenic butterfly valve is very high in the case of valve opening angle below 10 degree and incident velocity over 6m/s. By increasing the inlet velocity at 10 degree of valve opening angle. the value of loss coefficient increased. However. by increasing the inlet velocity at 50 degree of valve opening angle. the value of loss coefficient decreased.

• 대한기계학회논문집B
• /
• 제40권10호
• /
• pp.645-651
• /
• 2016

본 연구에서는 압력면익단소익의 폭이 터빈 동익 압력면스퀼러팁 하류의 팁누설유동 및 압력손실에 미치는 영향에 대하여 연구하였다. 팁간극비 h/s = 1.36%에 대하여, 흡입면스퀼러의 높이는 $h_p/s=3.75%$로 일정하게 유지하고, 압력면익단소익의 폭은 w/p = 2.64%, 5.28%, 7.92%, 10.55% 등으로 변화시키면서 실험을 수행하였다. 일반적으로 압력면익단소익의 폭이 증가할수록, 통로와류 영역에서의 압력손실은 감소하였지만 팁누설유동 영역에서는 압력손실이 오히려 증가하였다. 그 결과 익단소익의 폭이 증가할수록, 질량평균 압력손실은 매우 소폭 감소하는 경향을 보였다. 본 연구 결과, 압력면스퀼러팁에 설치된 압력면익단소익은 압력손실 저감에 거의 기여를 하지 못함을 확인할 수 있었다.

• 한국유체기계학회 논문집
• /
• 제7권5호
• /
• pp.36-42
• /
• 2004

The effect of tip clearance height on the three-dimensional flow and aerodynamic loss in the wake region of a high-turning turbine rotor cascade has been investigated with a miniature cone-type five-hole probe. Distributions of velocity magnitude, secondary velocity vectors, and total-pressure loss coefficient are presented for three tip gap-to-span ratios of h/s = 0.0, 0.5 and 1.0 percent. The result shows that with the increment of h/s, tip leakage vortex tends to be intensified and aerodynamic loss due to the leakage vortex is increased as well. In the case of h/s = 1.0 percent, aerodynamic loss in the tip-leakage flow region is found dominant in comparison with that in the passage vortex region. With increasing h/s, mass-averaged secondary loss coefficient has a greater portion in the mass-averaged total-pressure loss coefficient.