• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.1
• /
• pp.23-32
• /
• 2016

Various studies have been conducted for drag reduction of a high-speed vehicle by injecting counterflow jet from its nose cone. In this study, in order to obtain baseline data and key parameters for drag reduction method, the counterflow jet study of the USA is reviewed and summarized. The nose cone shapes of each study are hemisphere cylinder, truncated cone, and reentry capsule, and their test conditions are summarized accordingly. Key parameters for drag reduction are jet mach number, mass flow rate, and pressure ratio. Even though drag reduction effects show various results according to given test conditions, it is found that the drag reduction effect reaches up to 40~50%.

• Journal of Environmental Science International
• /
• v.16 no.4
• /
• pp.449-458
• /
• 2007

Research results for the pressure drop variance depending on operation conditions such as change of inlet concentration, pulse interval, and face velocity, etc., in a pulse air jet-type bag filter show that while at $3kg/cm^2$ whose pulse pressure is low, it is good to make an pulse interval longer in order to form the first layer, it may not be applicable to industry because of a rapid increase in pressure. In addition, the change of inlet concentration contributes more to the increase of pressure drop than the pulse interval does. In order to reduce operation costs by minimizing filter drag of a filter bag at pulse pressure $5kg/cm^2$, the dust concentration should be minimized, and when the inlet dust loading is a lower concentration, the pulse interval in the operation should be less than 70 sec, but when inlet dust loading is a higher concentration, the pulse interval should be below 30 sec. In particular, in the case that inlet dust loading is a higher concentration, a high-pressure distribution is observed regardless of pulse pressure. This is because dust is accumulated continuously in the filter bag and makes it thicker as filtration time increases, and thus the pulse interval should be set to below 30 sec. If the equipment is operated at 1m/min of face velocity, while pressure drop is low, the bag filter becomes larger and thus, its economics are very low due to a large initial investment. Therefore, a face velocity of around 1.5 m/min is considered to be the optimal operation condition. At 1.5 m/min considered to be the most economical face velocity, if the pulse interval increases, since the amount of variation in filter drag is large, depending on the amount of inlet dust loading, the operation may be possible at a lower concentration when the pulse interval is 70 sec. However, for a higher concentration, either face velocity or pulse interval should be reduced.

• Journal of computational fluids engineering
• /
• v.13 no.4
• /
• pp.33-38
• /
• 2008

For study on the unsteady blockage effect, flows around a rotationally oscillating circular cylinder with relatively low forcing frequency in closed test-section wind tunnels have been numerically investigated by solving compressible Navier-Stokes equations. The numerical scheme is based on a node-based finite-volume method with the Roe's flux-difference splitting and an implicit time-integration method coupled with dual time-step sub-iteration. The computed results of the oscillating cylinder in the test section showed that the fluctuations of lift and drag are augmented by the blockage effects. The drag further increases because of low base pressure. The pressure on the test section wall shows the harmonics having the oscillating and the shedding frequencies contained in the blockage effect.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.11 no.2
• /
• pp.23-31
• /
• 2008

The configuration model of a ballute type RAID(Ram Air Inflated Decelerator) for reducing the high speed and high revolution of smart submuntion is designed and tested. Three dimensional incompressible turbulent flow computational fluid dynamic analysis for the assembly of ballute and submunition is performed and pressure distribution, velocity, and drag around the assembly is calculated. Aerodynamic characteristics of the ballute assembly such as air flow inside and outside of the ballute and pressure distribution is clearly shown and it's drag coefficient is computed. Trajectory analysis of the submunition is performed and is in good agreement with the descending trajectory data of experimental model tested.

• Journal of the Korean Society of Industry Convergence
• /
• v.20 no.4
• /
• pp.339-343
• /
• 2017

Masks are a portable functional product for daily use. They can protect user health by filtering harmful fine particles in the air. In the past decade, there have been approximately 10 yellow dust incidences per year, amounting to a total duration of 20 days, and they continue to increase year after year. In addition, the frequency of yellow dust incidences in Korea has increased by more than four times compared to levels from the 1970s. Statistical reports indicate that annual damages caused by yellow dust amount to more than six trillion KRW. This study developed a zero-fog multi-layer mask with a collection efficiency and yellow dust and particulate matter filtration areas that are at least thrice as effective as existing masks. The new mask also reduces pressure drag by half.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.64.1-64.1
• /
• 2011

Small horizontal axis wind turbines (HAWTs) can be used to produce power in areas where the wind conditions are not favorable or optimal for large HAWTs. A newly designed airfoil for use in small HAWTs was analyzed in CFD to predict the aerodynamic performance at various Reynolds numbers over a various angles of attack. The coefficient of lift and drag, CL and CD, and the pressure distribution over the airfoil was obtained. It was found that the airfoil could achieve very good aerodynamic characteristics. The results of the numerical analysis will be compared against experimental data for validation purposes.

• The KSFM Journal of Fluid Machinery
• /
• v.14 no.2
• /
• pp.25-28
• /
• 2011

The control rod assemblies do freely fall into the reactor core by the gravity from the control rod drive mechanism. In order to achieve a rapid shutdown and control the reactor power, it is required to insert control rod assemblies as soon as possible. In this paper, we evaluated the drop time and flow characteristics caused around guide tube for SMART(System-integrated modular advanced reactor) control rod assembly. Numerical analyses are carried out with FLUENT program of computational fluid dynamics. This study results show that the drop time of the control rod assembly in the operating condition of SMART is more 20 percent rapidly than the drop time of the room temperature and ambient atmosphere condition.

• Journal of Ocean Engineering and Technology
• /
• v.12 no.2 s.28
• /
• pp.79-86
• /
• 1998

A three-dimensional WIG (Wing In Ground effect) moving above free surface is numerically studied by means of finite difference techniques. The air flow field around the WIG is analyzed by MAC (Marker & Cell) method, and interactions between WIG and the free surface are appeared as the variation of pressure distribution acting on the free surface. To analyze the wavemaking phenomena by those pressure distributions, the NS (Navier-Stokes) solver is employed in which nonlinearities of the free surface conditions can be included. Through the numerical simulation, Cp values and lift/drag ratio are carefully reviewed by changing the height/chord ratio. The section shape of model is NACA0012 with the span/chord ratio of 3.0. Through computational results, it is confirmed that the effect of free surface is small enough to treat it as a rigid wavy wall.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.2101-2104
• /
• 2003

Experimental investigations are performed for the rarefied gas flows in a disk-type drag pump (DTDP). The pump considered in this paper consists of grooved spiral channel on rotors and planar stators. The flow-metre method is adopted to calculate the pumping speed. Compression ratio and pumping speeds for the nitrogen gas are measured under the inlet pressure range of $0.001{\sim}4$ Torr. The maximum of compression ratio was about 3300 for three-stage DTDP, 1000 for two-stage and 100 for single-stage DTDP at zero throughput. The number of stage influences the pumping speed of DPDT

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.12
• /
• pp.961-967
• /
• 2009

A 3-dimensional numerical investigation of a WIG effect vehicle with DUP (direct underside pressurization) is performed to predict aerodynamic characteristics and the static height stability. DUP can considerably reduce take-off speed and minimize the hump drag while the vehicle accelerates on the water to take off. The DUP of the model vehicle, Aircat, consists of a propeller in the middle of the fuselage and an air chamber under the fuselage. The air accelerated by the propeller comes into the camber through the channel in the middle of fuselage and augments lift by changing its dynamic pressure to static pressure dramatically. However, the air accelerated by a propeller produces excessive drag and reduces static height stability.