• 한국세라믹학회지
• /
• 제30권1호
• /
• pp.62-68
• /
• 1993

Densification of alumina powder, grain size and fracture toughness of sintered body by hot pressing after cold compaction were investigated and compared to traditional hot pressing process (without cold cyclic compaction). To achieve a higher densification and to reduce the hot pressing time, hot pressing after cold cyclic compaction was more efficient compared to traditional hot pressing. This phenomenon resulted from the increment of packing densityby the acceleration fo rearrangement of powders under cold cyclic compaction. The grain size of sintered body was only dependent on relative density, and densification during hot pressing was governed by thelattice diffusion. Comprisons of grain size, densification mechanism and fracture toughness resulted from hot pressing after/without cold cyclic compaction showed that a low cyclic pressure may not effect on the fragmentation of alumina powders.

• 에너지공학
• /
• 제1권1호
• /
• pp.58-65
• /
• 1992

인산형 연료전지의 전극성능의 향상을 위해 Hot Pressing공정을 사용하여 Pt이 담지된 다공성 탄소전극(Pt/C)을 제조하였다. Hot pressing의 조건, 촉매층에서의 PTEE 함량을 변화시켜 제조한 Pt/C 전극의 전기화학적 산소환원특성 및 인산형 단위전지 성능특성을 비교하였다. 실험결과 Hot Pressing의 최적조건은 36$0^{\circ}C$, 10kg/$\textrm{cm}^2$이었다. 최대성능은 촉매층에 30wt%의 PTFE 함량을 가진 전극에서 얻어졌으며, 이때 백금의 이용율은 80%이었다. 단위전지의 성능측정 결과, hot pressing한 전극의 성능은 700㎷에서 200mA/$\textrm{cm}^2$이었으며 200시간동안 안정적인 성능이 유지되었다.

• 한국재료학회지
• /
• 제15권7호
• /
• pp.473-479
• /
• 2005

Thermoelectric $Zn_4Sb_3$ alloys were synthesized by a conventional powder metallurgy process consisting of solid state reaction and hot pressing. Single phase $Zn_4Sb_3$ was successfully produced by the annealing of cold compact starting with the mixed elemental powders, and subsequent hot pressing yielded single phase bulk specimens without microcracks. Phase transformations in this alloy system during synthesis were investigated using XRD, SEM and EDS. Thermoelectric properties as a function of temperature were investigated from room temperature to 600 K and compared with results of analogue studies. Transport properties at room temperature were also evaluated. Thermoelectric properties of single phase $Zn_4Sb_3$ materials produced by this process are comparable to the published data. Synthesis by solid state reaction and hot pressing offers a potential processing route to produce a bulk $Zn_4Sb_3$.ٓ

• 한국결정성장학회지
• /
• 제16권1호
• /
• pp.38-42
• /
• 2006

본 1부 연구에서는 스파크 플라스마 열에 의한 그린 세라믹의 소결에서 열전달 및 가압력으로 인한 상대밀도의 변화를 유한요소법(FEM)으로 해석하고 그 결과에 따른 입자성장을 몬테카를로법(MCM)을 이용하여 전산모사하는 방법을 제시하기 위하여 SPS의 FEH 해석과 MCM 해석의 이론적 배경을 기술한다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.203-204
• /
• 2006

There is an increasing demand for PM-processes with the capability to produce parts of higher complexity than with conventional press and sinter technology in high production numbers. Warm-flow-compaction (WFC) makes use of improved flowability of powders when blended in an appropriate ratio with fine powder fractions and lubricating binders. Here the process is shown with examples of PM-Steels. General features possible with the process like pressing of undercuts and threaded bores are shown.

• 한국분말재료학회지
• /
• 제3권4호
• /
• pp.253-259
• /
• 1996

The efficiency of thermoelectric devices for different applications is known to depend on the thermoelectric effectiveness of the material which tends to grow with the increase of its chemical homogeneity. Thus an important goal for thermal devices is to obtain chemically homogeneous solid solutions. In this work, the new process with rapid solidification (melt spinning method) followed by hot pressing was investigated to produce homogeneous material. Characteristics of the material were examined with HRD, SEM, EPMA-line scan and bending test. Property variations of the materials were investigated as a function of variables, such as dopant ${CdCl}_{2}$ quantity and hot pressing temperature. Quenched ribbons are very brittle and consist of homogeneous $Bi_2Te_3$, ${Bi}_{2}{Se}_{3}$ solid solutions. When the process parameters were optimized, the maximum figure of merit was 2.038$\times$$10^{-3}K^{-4}. The bending strength of the material hot pressed at 50$0^{\circ}C$ was 8.2 kgf/${mm}^2$.

• 소성∙가공
• /
• 제17권6호
• /
• pp.407-411
• /
• 2008

A brake system in automobile is one of the important parts that directly affect the safety of passengers. Particularly, disk brake module is applied to almost all kinds of automobile brake system due to its remarkable braking power and braking distance. In the disk brake module of an automobile, the bolt for tire wheel is assembled to the disk brake hub by interference fit(bolt pressing process). The process induces small deformation whose range is within tens of ${\mu}m$ and this deformation may cause the runout badness of the whole disk brake module, and even braking problems such as judder or squeal phenomena which makes the loss of braking efficiency. In this study, bolt pressing fit into hub was simulated by $ANSYS^{TM}$, a commercial structure analysis program. Also, the aspect and the cause of hub displacement were analyzed and the solution for decreasing runout of hub was proposed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.267-270
• /
• 2009

In the present investigation, we are newly developing a new forming process which can fabricate micro patterns on large-area polymeric substrates for high speed mass production. The key idea of the new process is to pressurize multiple vacuum-packed substrate-mold stacks above the glass transition temperature ($T_g$) of the polymeric substrates. The new process is thought to be promising micro-pattern fabrication technique in three aspects; firstly, isostatic pressing ensures the uniform micro-pattern replicating condition regardless of the substrate area. Secondly, the control of forming condition such as temperature and pressure can realize well-defined process condition exploited in the conventional hot embossing research field. Thirdly, multiple substrates can be patterned at the same time. A prototype forming machine for the new process was developed with the design consideration realizing the present idea. With a developed machine, micro prismatic array patterns with 50 um in size were successfully made on the $380{\times}300{\times}6\;mm$ PMMA plate.

• 대한기계학회논문집A
• /
• 제32권4호
• /
• pp.333-339
• /
• 2008

Densification behavior of copper powder was investigated to study the effect of an aluminum mold under warm pressing. The low flow stress of an aluminum mold is appropriate to apply hydrostatic stress to powder compacts during compaction under high temperature. The suggested powder metallurgy process is very useful under high temperature since copper powder compacts have higher relative density over axial stress of 100 MPa and show more homogeneity as compared with conventional warm pressing. Elastoplastic constitutive equation proposed by Shima and Oyane was implemented into a finite element program (ABAQUS) for densification behavior under warn pressing by using a metal mold. Finite element results agreed well with experimental data for densification and deformation of copper powder compacts in the mold.

• 펄프종이기술
• /
• 제44권6호
• /
• pp.21-27
• /
• 2012

The effects of fines contents in OCC stock on the wet pressing process were evaluated in this study. The fines were collected from the beaten OCC stock by using 200 mesh. The dryness of handsheet samples after the couch and after the 1st wet press were greatly affected by the fine contents of the OCC stock. The higher contents of fines resulted in the lower value in dryness but the higher value of density followed by the higher strength properties. The addition of the retention aids and the drainage aids on the OCC stocks showed the wet pressing efficiency were greatly affected by the fine contents rather than the addition of polymer additives. The increase in the fine retention by the polymer additives offset the improvement in the wet pressing efficiency originated from the polymer additives.