• 전기전자학회논문지
• /
• 제9권1호
• /
• pp.47-56
• /
• 2005

본 연구에서는 불확실성과 부하 변동 하에 브러쉬없는 직접구동 전동기의 정확한 사전결정 추적성능을 제공하기 위한 새로운 개선된 강인한 가변구조 추적 제어기를 설계하였다. 리칭 페이즈를 제거하기 위한 특수 적분 슬라이딩 변은 서보 전동기의 초기 위치부터 이상 슬라이딩 모드와 가상 이상 슬라이딩 궤적을 정의한다 . 영이 아닌 슬라이딩 면에 의하여 발생되는 추적오차를 유도하였다. 외란 관측기를 갖는 연속 입력을 제안하여 불확실성과 부하 변동 하에 사전 결정 가상 이상 슬라이딩 궤적을 사전 값 내에 추적하도록 한다. 제안된 알고리듬의 유용성을 부하 변동 하에 브러쉬없는 직접구동 전동기에 대한 비교 시뮬레이션으로 입증한다.

• 대한의용생체공학회:의공학회지
• /
• 제3권1호
• /
• pp.23-30
• /
• 1982

The regimen of physical activity of the patient with coronary artery disease requires that he should not overshoot the prescribed heart rate based on his age, health and fuctional status of the heart during his exercise. The step input of work load, however, involves a great danger of overshooting. The purpose of this study was to desigil a system that makes it passible for a subject to check the overshooting. This system shows on tile H.R-meter, the amplified and filtered heart-rate signal of the subject received by the photosensor on his earlobe, puts it in the lead coinpensational circuit where it is conpared with the reference input signal(=the presfribed heart rate). The output of the lead compensational circuit works the aull meter. By means of this null meter, the subject knows whether he is overshooting the prescribed heart rate or not. He can continue the natl meter needle at the'Zero'position through the control of the speed of pedaling of the bicycle ergometer, An experimental test, made on eight men and four women in healthy condition, showed that 91. 7% of them vlaintained the stable heart rate and that the overshooting of the desired heart rate did not exceed $\pm$2BPM. According to the result of this experiment, since the heart rate feedback controller makes it possible for the subject to take the prescribed exercise based not on the work load but on the heart rate which incidentally is inexpensive, it can be made use of as the instrument for the regimen of pflysical activity by the patient with coronary artery disease.

• 대한기계학회논문집
• /
• 제17권6호
• /
• pp.1478-1485
• /
• 1993

본 연구에서는 압축 성형다이 가열선의 최적위치를 결정하는 문제를 다이의 형상 최적설계 문제로 정식화하고자 한다. 최적화 문제의 목적은 다이 내면의 온도를 지정된 온도로 균일하게 유지하는 것이다. 또한 Lee, Choi와 Kwak의 형상 설계 민감 도 해석을 위한 직접 미분 방법을 응용하여 가열선 위치변화에 관한 민감도 계산을 위한 경계 적분 방정식을 유도하고, 경계요소법으로 온도와 온도의 민감도를 해석하고 자 한다. 수치적 응용의 예로서, 넓은 평판의 성형을 위한 압축 성형다이의 가열선의 최적위치를 결정하는 문제를 다루고, 최적위치에서 가열선의 개수가 온도의 균일성에 미치는 영향을 검토한다.

• 한국멀티미디어학회논문지
• /
• 제22권9호
• /
• pp.1011-1019
• /
• 2019

In this paper, we propose a system that can more precisely identify and monitor the position of the tool used in the assembling workplace such as automobile production. The proposed positioning monitoring system is a combination of UWB communication module and MEMS IMU sensor. Since UWB does not need modulation and demodulation function and has low power density, UWB is widely used in indoor positioning field. However, it may cause positioning error due to errors in RF transmission and reception process, which may cause positioning accuracy. Therefore, in this paper, we propose an algorithm that uses IMU as an auxiliary means to compensate for errors that may occur in positioning using only UWB. The tag and anchor of UWB module measure the transmission / reception time by transmitting signals to each other and then estimate the distance between tag and anchor. The MEMS IMU sensor serves to provide positioning calibration information. The tag, which is a mobile node and attached to a moving tool, measures the three-dimensional position of the tool and transfers the coordinate data to the anchor. Thus, it is possible to confirm whether or not the specific tool is properly used according to the prescribed regulations.

• 한국생산제조학회지
• /
• 제20권2호
• /
• pp.121-128
• /
• 2011

As high precision industries such as semiconductor, TFT-LCD manufacturing and MEMS continue to grow, the demand for higher DOF precision stages has been increasing. In general, the stages should accommodate a prescribed range of payloads in order to position various precision manufacturing/inspection instruments. Therefore a nonlinear controller using sliding motion is developed, which bears mass perturbation and makes the upper plate of the stage move in 6 DOF. For the application of the nonlinear control, an observer is also developed based on expected noise covariance. To eliminate the steady state error of step response, integral terms are inserted into the state-space model. The linear term of the controller is designed using optimization scheme in which parameters can be weighted according to their physical significance, whereas the nonlinear term of the controller is designed using trial and error method. A comprehensive simulation study proves that the designed controller is robust against mass perturbation and completely eliminates steady state errors.

• Journal of Theoretical and Applied Mechanics
• /
• 제2권1호
• /
• pp.1-14
• /
• 1996

In this paper, breaking waves are generated in a 2-D wave tank and simulated by using a higher-order boundary element method. A piston-type wavemaker is operated by signals composed of elementary waves. The phase of elementary waves is determined by the linear theory such that they are focused to a prescribed position. Calculated plunging waves coincide well with experiment. A steel box with different plate thicknesses is installed at a predetermined position in the tank. Measured impulsive pressures due to breaking waves are found to be 0.8-1.2$\rho$C2, where $\rho$ corresponds to water density and C to wave celerity. The transverse displacement of the plate is described in terms of modal eigenfunctions. The natural frequencies measured by impact tests in air for thin plate coincide with the computational and theoretical values. The radiationpotential due to plate vibration is derived and the radiation force is expressed in terms of hydroelastic added mass and damping forces. Comparison of natural frequencies of plate in water proves that hydroelastic added mass and damping are properly considered. The measured strain due to regular waves supports the calculated one, but there are apparent discrepancies between theory and experiment in the impulsive case.

• Journal of Ship and Ocean Technology
• /
• 제11권1호
• /
• pp.36-46
• /
• 2007

The maintenance of a ship is essential for safe navigation and hence regular surveys are prescribed according to the rule of classification societies. A hull inspection is generally performed by professional divers, but it takes a long time and the efficiency is low in terms of time and cost. In this research, a ROV(Remotely Operated Vehicle) named as SNU-ROV(Seoul National University-ROV) is developed to replace the conventional inspection method. In this system, the ROV is intended to be used for inspecting ship and harbor because harbor inspection is merging as a safety measure against any possible terror actions. In order to increase the efficiency of inspection, the ROV must be able to measure the exact position of damages. SNU-ROV has a positioning system based on LBL(Long Base Line). In shallow water such as harbor, however, LBL has bad DOP(Dilution of Precision) in the depth direction due to the limited depth. Thus LBL only can not locate the exact depth position. To solve the DOP problem, a pressure sensor is introduced to LBL and a complementary filter is attached by using indirect feedback Kalman filter. Thus developed positioning system is verified by simulation and experiment in towing tank.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.314-319
• /
• 2002

The Automation and Control Group at the University of Brasilia is developing an automatic welding station based on an industrial robot and a controllable welding machine. Several techniques were applied in order to improve the quality of the welding joints. This paper deals with the implementation of a laser-based computer vision system to guide the robotic manipulator during the welding process. Currently the robot is taught to follow a prescribed trajectory which is recorded a repeated over and over relying on the repeatability specification from the robot manufacturer. The objective of the computer vision system is monitoring the actual trajectory followed by the welding torch and to evaluate deviations from the desired trajectory. The position errors then being transfer to a control algorithm in order to actuate the robotic manipulator and cancel the trajectory errors. The computer vision systems consists of a CCD camera attached to the welding torch, a laser emitting diode circuit, a PC computer-based frame grabber card, and a computer vision algorithm. The laser circuit establishes a sharp luminous reference line which images are captured through the video camera. The raw image data is then digitized and stored in the frame grabber card for further processing using specifically written algorithms. These image-processing algorithms give the actual welding path, the relative position between the pieces and the required corrections. Two case studies are considered: the first is the joining of two flat metal pieces; and the second is concerned with joining a cylindrical-shape piece to a flat surface. An implementation of this computer vision system using parallel computer processing is being studied.

• 국제학술발표논문집
• /
• The 6th International Conference on Construction Engineering and Project Management
• /
• pp.328-332
• /
• 2015

By logging position data from GPS-equipped construction machines, we re-create daily activities as 3D animations to analyze performance and facilitate look-ahead scheduling. The 3D animation enables going back to any point in time and space to observe the activities as they took place. By segmenting data into a set of activities, it is possible to obtain actual measures of performance such as cycle times, production, speed profiles and idle times. The measures of performance can then be compared to those expected (e.g., theoretical speed profiles vs. observed profiles), and instances of significant difference can be flagged for further investigation. Idle times and queues that exceed prescribed thresholds can also be identified. In general, many of the traditional real-time performance analyses can be performed after the fact. Situations of interest can be identified automatically and the events in this manner enhances effective performance improvement in construction. The proposed research is explained and demonstrated using a real push-loaded earthmoving operation.

• 대한인간공학회지
• /
• 제30권4호
• /
• pp.459-464
• /
• 2011

It is prescribed for the controls layout of agricultural tractors to offer a comfortable workspace in ISO 4253 as international standard. To export other country to the Korea agricultural tractor, it needs to come up to the nation standard. The objective of the study is to investigate for location of control operation of the Korea agricultural tractor after applying the ISO 4253, to know whether it suits or not the nation standards with the tractor of product and supply within the country. As the research result of Korea agricultural tractor, Controls position of them are few in zone of comfort which defined in ISO 4253 and escapes lots in the zone of reach.