• 멤브레인
• /
• 제15권2호
• /
• pp.85-104
• /
• 2005

Recently, membrane can be prepared by two methods, phase inversion and electrospinning techniques. Phase inversion technique is a conventional but commercially preparation membrane. The most versatile of preparation in this technique is immersion of the cast film into nonsolvent bath, causing dense top layer with a finger-like pattern in the sub layer membrane. The membrane pore size getting from phase inversion is in the range of micro or submicrometer. As a result, it can be used as microfiltration and ultrafiltration applications. A new technique, electrospinning, is introduced for membrane preparation. Nonwoven nanofibrous mat or nanofibrous membrane is obtained. In this technique, electrostatic charge is introduced to the solution jet, causing a thin fiber with high surface area; hence it can be used in the applications where high surface area-to-volume or length-to-diameter ratios are required. Moreover, the pore size can be controlled by controlling the time of electrospinning. Hence, it can be used as a filter for filtering microparticles as well as nanoparticles.

• 한국세라믹학회지
• /
• 제28권5호
• /
• pp.353-358
• /
• 1991

Fine powders of the 2212 superconducting phase of bismuth system have been prepared directly from solution using ultrasonic spray pyrolysis. The fine superconducting powders produced by pyrolysis were characterized for the size, shape, and crystalline phase by SEM and XRD. The pyrolysis temperature, flow rate of the carrier gas, residence time of the droplets greatly influenced the size, shape, and crystalline phase. The optimum temperature and flow rate of the carrier gas for the preparation of fine powders of the 2212 superconduting phase were found to be 830$^{\circ}C$and 3ι/min, respectively.

• 한국운동역학회지
• /
• 제13권2호
• /
• pp.49-63
• /
• 2003

For this study, four male university Taekwondo players were randomly chosen, between the weight categories of 60Kg and 80Kg. Their side kicks (yeop chagi), which are part of foot techniques, were kinematically analyzed in terms of the time, angle, and angular velocity factors involved with the kicks through the three-dimensional imaging. The results of the analysis are as fellows. 1. Time factor The first phase(preparation) was 0.48sec on average, accounting for 60% of the entire time spent; the second phase(the minimum angle of the knee joint) was 0.21sec on average, taking up 26% of the whole time spent; and the third phase(hitting) was 0.11sec on average, representing 14% of the entire time spent. 2. Angle factor In the first phase(preparation), rotating their bodies along the long axis, the players bended their hip and knee joints a lot, by moving fast in the vertical and horizontal directions, in the second phase(the minimum angle of the knee joint), the players continued to extend their bodies along the vertical axis, while pronating their lower legs and bending their hip and knee joints a lot to reduce the radius of gyration, and in the third phase(hitting), they extended their knee joints greatly so that the angle movements of their lower bodies shifted to circle movements. 3. Angular velocity factor In the first phase(preparation), the angular velocity of the hip and knee joints increased. while moving horizontally and rotating the body along the long axis; in the second phase(the minimum angle of the knee joint), the angular velocity increased by bending the hip and knee joints fast to reduce the rotation radios; and in the third phase(hitting), the angular velocity was found to have increased, by rotating the body along the long axis to increase the angular velocity and shifting the angular momentum of the pronated knee joint to the circular momentum.

• 한국응용과학기술학회지
• /
• 제20권1호
• /
• pp.44-50
• /
• 2003

We studied on the preparation and evaluation of O/W type microemulsion containing "wax, liquid paraffine and quaternary ammonium salt". And also it was obtained to stability of microemulsions by mono ethylene glycol(MEG) addition. The microemulsions were generally prepared at 96${\sim}$97$^{\circ}C$ by the phase inversion method. We used polyoxyethylene(20) sorbitan monooleate(POE(20)SMO) and distearyl dimethyl ammonium chloride(D.D.A.C.) as the emulsifiers at microemulsion preparation. From the results, we could get best condition for microemulsion preparation, in case of oil phase, montanic ester wax ; 1.1wt%, paraffine wax ; 1.1wt%, liquid paraffine ; 3.1wt%, propylene glycol ; 0.6wt% and ethylene glycol monobutyl ether ; 0.6wt%, when the ratio(wt%) of D.D.A.C. and POE(20)SMO were 2 : 3. And also we could obtained that the distributed particle size of the final microemulsions were about 8${\pm}$1.5nm and the mean particle size was 7${\pm}$0.5nm. We got following results from final microemulsions that the percent of transmittance; 96${\sim}$98% at 700nm. And the microemulsion blended with MEG of 5${\sim}$15wt% showed smaller particle size and more stable distribution than non-containing MEG.

• Archives of Pharmacal Research
• /
• 제19권1호
• /
• pp.30-35
• /
• 1996

Poly(l-lactic acid)(PLLA) microspheres loaded with ampicillin sodium (AMP-Na_, .betha.-lactam antibiotic, were prepared by a w/o/w multiple emulsion-solvent evaporation method. The amounts of each component in three phases (inner water phase, organic phase, and outer water phase) wre carefully examined in the preparation of PLLA microspheres. The stirring rate, another preparation parameter, was also investigated for study on the effect of mechanical stress on the drug loading and morphology of PLLA microspheres. Most of the preparation parameters had a great influence on the drug loading, surface morphology and size distribution of PLLA microspheres. PLLA microspheres with 15.89 w/w% drug loading were subjected to the in vitro release experimet. The release of ampicillin sodium was constant at a rate of 1.68 $mug/ml/day$ per 1 mg of microspheres for 18 days initial burst effect.

• 한국운동역학회지
• /
• 제14권1호
• /
• pp.117-131
• /
• 2004

The foreign superior players and national team players' turning phase was measured, compared and analyzed to help the representative players improve the skill of turn. The underwater video camera used to analyze and evaluate the representative players' skill of turn in detail and the result is as follows. 1. The record for the phase of turn was similar to the rank of the last record. The improvement of the skill of turn was required because Korean players' record was lower than the foreign players' one. In case of 200m events the 1st turn was the fastest and it took more time as the turn is repeated. 2. It shows that the preparation phase and turing motion cause the difference between the players and within one player. 3. The horizontal movement of center of gravity moves to turning point slowly in the preparation phase, does not move nearly in the turning phase and increase again in the propulsion phase. Good record has short time for turn phase. The result means that the shorten the turning phase is the most important factor. Therefore the preparation for this is required. The vertical movement is maintained or increase a little and then move to from the turning phase. 4. The characteristic of horizontal velocity in center of gravity is that there is any big changes at the preparation phase, the faster velocity is found from the better record and the accelerating time is fast at the propulsion phasen. The wrong motion is made by not using the swimming velocity for fuming and waiting and more time is required by this. 5. The angle of knee when the player touch the turning point is 106.22-135.56 and the maximum angle of knee during the driving after the touch of tuning point is full extension. The size of maximum angle of knee did not match with the required time of propulsion phase. It seems that the individual difference is big when the players touch the turning point the angle of knee and the research for the individual angle which can reveal the maximum power should be carried out. The national team player's skill for the him is behind the foreign players' one and a lot of problems were found. It shows that the players could not practice the skill for turn during the training. The 1st reason for it is the various facilities like underwater window or analyzing equipment like underwater camera with which the coaches can teach and correct the players' detailed skill. It is need to evaluate the players' detailed skill exactly and correct it by objective data to complete the good skill in the future. In this regard, the investment for the facility is necessary.

• 공학교육연구
• /
• 제17권2호
• /
• pp.11-24
• /
• 2014

The purpose of this study is to develop a teaching-learning model of convergence project based on team teaching. Based on development research methodology which explored a university case, the teaching-learning model was developed including three phases such as preparation, planning, and implementation & evaluation. The preparation phase has three steps as follows: to organize team teaching faculty; to develop convergence projects cooperated by industry and university; and to design instructions based on supporting convergence projects. The last step of preparation phase consists of five design activities of: (1) instructions and teaching contents; (2) communication channel among faculty members; (3) feedback system on students' performance; (4) tools to support learners' activity; and (5) evaluation system. The planning phase has two steps to analyze learners and to introduce and modify instruction and themes of convergence projects. The implementation & evaluation phase includes five steps as bellow: (1) to organize project teams and match teams with faculty members; (2) to do team building and assign duties to students of a team; (3) to provide instruction and consulting to teams; (4) to help teams to conduct projects through creative problem solving; and (5) to design mid-term/final presentation and evaluation. Lastly, the research implications and limitations were discussed for future studies.

• 폴리머
• /
• 제34권3호
• /
• pp.261-268
• /
• 2010

본 연구에서는 상전이 온도가 36 $^{\circ}C$인 n-eicosnae을 열가소성 폴리올레핀 고분자인 폴리프로필렌과 블렌드하였으며, 또한 최근의 형태안정성 PCM(SSPCM)의 연구검토를 통하여 폴리프로필렌과 n-eicosnae의 특성과 잠열저장체로서의 적용 가능성을 확인하였다. 상전이 온도가 36 $^{\circ}C$인 n-eicosane과 폴리프로필렌을 멜팅방법과 흡수방법을 이용하여 시료를 제조하였다. 제조된 형태안정성 PCM(SSPCM)을 DSC, WAXD, FTIR spectroscopy, ARES로 분석결과 형태안정성, 열용량의 향상을 확인하였다.

• 한국세라믹학회지
• /
• 제32권10호
• /
• pp.1123-1130
• /
• 1995

In the preparation of manganese zinc ferrite powders by alcoholic dehydration of citrate/formate solution. The effect of pH change on precipitation was investigated. The pH range for obtaining stable precipitates was studied. The glassy phase was obtained when the pH value of solution is higher than 5, and the formation mechanism of glassy phase was suggested. Below pH 5, the stable precipitates were formed, and the optimal pH was 2. Formation of glassy phase was accounted for the change of surface charge by pH change. The change of surface charge is caused by the interparticular agglomeration. The precipitate was redissolved into the water on the surface of precipitate itself and through the polymerization, it agglomerated. This mechanism is tought to be similar to that of viscous flow.

• Bulletin of the Korean Chemical Society
• /
• 제10권1호
• /
• pp.19-22
• /
• 1989

The suitability of BMPI (2-bromo-N-methyl pyridinium iodide) for solid-phase peptide synthesis was investigated. The coupling rate of BMPI/HOBT procedure. BMPI/HOBT was superior to DCC/HOBT couplings using the solid-phase peptide bond formation proceeded to a greater degree of completion than DCC/HOBT method did. Double couplings with 2 equiv. of Bocamino acids and 1.5 equiv. of BMPI and $NEt_3$ and 2 equiv. of HOBT in DMF/MC (1:1 v/v) gave the best result for the preparation of a model compound. Stepwise solid phase peptide synthesis using BMPI/HOBT procedure was successfully utilized for the preparation of $(D-Ala)^2$-dynorphine A. BMPI/HOBT procedure for the synthesis of $(D-Ala)^2$-dynorphine gave better yield (20%) than DCC/HOBT procedure did.