• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.11
• /
• pp.46-56
• /
• 1996

Planarization technique is rapidly recognized as a critical step in chip fabrication due to the increase in wiring density and the trend towards a three dimensional structure. Global planarity requires the preferential removal of the projecting features. Also, the several materials i.e. Si semiconductor, oxide dielectric and sluminum interconnect on the chip, should be removed simultaneously in order to produce a planar surface. This research has investihgated the development of the chemical mechanical polishing(CMP) machine with uniform pressure and velocity mechanism, and the pad insensitive to pattern topography named hard grooved(HG) pad for global planarization. Finally, a successful result of uniformity less than 5% standard deviation in residual oxide film and planarity less than 15nm in residual step height of 4 inch device wafer, is achieved.

• Restorative Dentistry and Endodontics
• /
• v.9 no.1
• /
• pp.115-119
• /
• 1983

The purpose of this study was to compare the solubility of enamel and dentin to an etchant after fluoride application. Specimens were collected from extracted anterior and bicuspid and each tooth was cut into several pieces. These specimen were allocated in 7 group; 1%, 2%, 3% NaF, 1%, 8%, 20% $SnF_2$, and control group. Five specimens in each group was exposed to pre-determined fluoride solution for 3 minutes, and washed with running water. These specimens were etched by Hipol (commercial label) etchant for 30 seconds. Following are the findings obtained through S.E.M. 1. All specimens with acid etching revealed preferential removal of prism periphery leaving prism core. 2. Specimens treated with 1%, 2% NaF solution showed that the shape of prism tip was thin and sharp like a needle. The case of 3% NaF showed rather round shape at prism end. 3.1% of $SnF_2$ case showed similar findings with the control group but 8% and 20% $SnF_2$ case revealed needle shape at the prism and was less clear than NaF case. Preferential removal of prism periphery was partialy observed and un decalcified area is fused to prism forming reidge. 4. Dentine treated by fluoride compound in low concentration showed the orifice of dentinal tubule was clearly enlarged whereas in high concentration the orifice was not widened.

• Journal of Hydrogen and New Energy
• /
• v.27 no.5
• /
• pp.503-509
• /
• 2016

Fuel cell is a device for producing electricity by using the hydrogen produced by the fuel processor. At this time, CO is also created by the fuel processor. The resulting CO enters the stack where is produce electricity and leads to the adsorption of anode catalyst, finally the CO poisoning occurs. Stack which occurred CO poisoning has a reduction in performance and shelf life are gradually fall because they do not respond to hydrogen. In this paper, experiments that using a PROX reactor to prevent CO poisoning were carried out for removing the CO concentration to less than 10ppm range available in the fuel cell. Furthermore experiments by the PROX reaction was designed and manufactured with a water-cooling heat exchange reactor to maintain a suitable temperature control due to the strong exothermic reaction.

• Solar Energy
• /
• v.19 no.3
• /
• pp.125-131
• /
• 1999

This paper deals with a novel structure of poly-Si solar cell. A grain boundary(GB) of poly-Si acts as potential barrier and recombination center for photo-generated carriers. To reduce unwanted side effects at the GB of poly-Si, we employed physical GB removal of poly-Si using chemical solutions. Various chemical etchants such as Sirtl, Yang, Secco, and Schimmel were investigated for the preferential GB etching. Etch depth about 10 ${\mu}m$ was achieved by a Schimmel etchant. After a chemical etching of poly-Si, we used $POCl_3$ for emitter junction formation. This paper used an easy method of top electrode formation using a RF sputter grown ITO film. ITO films with thickness of 300 nm showed resistivity of $1.26{\times}10^{-4}{\Omega}-cm$ and overall transmittance above 80%. Using a preferential GB etching and ITO top electrode, we developed a new fabrication procedure of poly-Si solar cells. Employing optimized process conditions, we were able to achieve conversion efficiency as high as 16.6% at an input power of 20 $mW/cm^2$. This paper investigates the effects of process parameters: etching conditions, ITO deposition factors, and emitter doping densities in a poly-Si cell fabrication procedure.

• Macromolecular Research
• /
• v.12 no.1
• /
• pp.134-140
• /
• 2004

Semi-crystalline poly(ethylene terephthalate) (PET) film surfaces were modified with argon and oxygen plasmas by radio-frequency (RF) glow discharge at 240 mTorr/40 W; the changes in topography and surface structure were investigated by atomic force microscopy (AFM) in conjunction with specular reflectance of infrared microspectroscopy (IMS). Under our operating conditions, analysis of the AFM images revealed that longer plasma treatment results in significant ablation on the film surface with increasing roughness, regardless of the kind of plasma used. The basic topographies, however, were different depending upon the kind of gas used. The specular reflectance analysis showed that the ablative mechanisms of the argon and oxygen plasma treatments are entirely different with one another. For the Ar-plasma-treated PET surface, no observable difference in the chemical structure was observed before and after plasma treatment. On the other hand, the oxygen-plasma-treated PET surface displays a significant decrease in the number of aliphatic C-H groups. We conclude that a constant removal of material from the PET surface occurs when using the Ar-plasma, whereas preferential etching of aliphatic C-H groups, with respect to, e.g. , carbonyl and ether groups, occurs upon oxygen plasma.

• Bulletin of the Korean Chemical Society
• /
• v.29 no.5
• /
• pp.974-978
• /
• 2008

Removal of heavy metal ions ($Cd^{2+}$ and $Zn^{2+}$) by electrocoagulation (ECG) was investigated in an acidic condition, which is necessary for re-using or discharging the mediated electrochemical oxidation (MEO) media. Effects of various parameters such as electrolytes, current densities, and electrode materials were examined for a metal-contaminated MEO system using $Fe^{2+}/Fe^{3+}$ pairs as a mediator. It was found that ECG with Al electrodes is greatly affected by the presence of $Fe^{2+}$. [$Cd^{2+}$] and [$Zn^{2+}$] remain constant until [$Fe^{2+}$] reaches a certain concentration level (ca. 10 mM). This preferential removal of $Fe^{2+}$ during ECG with Al electrodes is not alleviated by controlling current densities, potential programs, and solution mixing. ECG with Fe electrodes, on the other hand, resulted in relatively fast removal of $Cd^{2+}$ and $Zn^{2+}$ under coexistence of $Fe^{2+}$, indicative of the different role between $Fe^{n+}$ generated from an electrode and $Fe^{2+}$ initially present in a solution. When ECG was performed with Fe electrodes until [$Fe^{n+}$] became the same as the concentration of initially present $Fe^{2+}$, [$Cd^{2+}$] and [$Zn^{2+}$] were reduced to one-tenth of the initial concentrations, suggesting the possibility of a continuous use of the medium for a subsequent MEO process.

• Journal of Korean Society for Atmospheric Environment
• /
• v.17 no.1
• /
• pp.67-74
• /
• 2001

In the manufacturing process of PCB , three kinds of VOCs such as aceton, methanol and 2-metoxyethanol are being used. In this study, adsorption characteristics of activated carbon fibers(ACFs) and active carbon were examined to temove these VOCs. The experimental results showed that ACF has better adsorption and regeneration efficiency than activated carbon. Phenolic-resin based ACF showed the highest adsorption capacity and the capacity was not decreased after repeated regeneration by steam. On the adsorption and desorption experiments for ternary components, preferential adsorption with roll-over phenomena was appeared. 2-Metoxyethanol was strong adsorbaste and it displaced adsorbed methanol and aceton.

• Corrosion Science and Technology
• /
• v.7 no.3
• /
• pp.158-161
• /
• 2008

It is well known that iron is one of the most common impurity elements found in aluminum and its alloys. Iron in the aluminum forms an intermetallic compounds such as $FeAl_3$. The $FeAl_3$ particles on the aluminum surface are one of the most detrimental phases to the corrosion process and anodizing procedure for aluminum and its alloys. Trial and error surface treatment will be carried out to find the preferential and effective removal of $FeAl_3$ particles on the surfaces without dissolution of aluminum matrix around the particles. One of the preferable surface treatments for the aim of getting $FeAl_3$ free surface was an electrochemical treatment such as cathodic current density of $-2kAm^{-2}$ in a 20-30 mass% $HNO_3$ solution for the period of 300s. The corrosion characteristics of aluminum surface with $FeAl_3$ free particles are examined in a $0.1kmol/m^3$ NaCl solution. It is found that aluminum with free $FeAl_3$ particles shows higher corrosion resistance than aluminum with $FeAl_3$ particles.

• Korean Membrane Journal
• /
• v.1 no.1
• /
• pp.38-42
• /
• 1999

Membrane technology can be applied in two ways to produce pure enantiomers. In one case a membrane separation process can be cmbined with an enantiospecific reaction to obtain so-called 'en-antiospecific membrane reacto' These systems are useful to carry out asymmetric synthesis or kinetic resolution and simulatneously separate the produced enantiomer. As for general membrane reactors the result is a more compact system with a higher conversion: in fact removal of a product drives equilibrium-limited reactions towards completion. The other way to apply membrane technology to chiral production is the use of intrinsically enantioselective membranes that are able to distinguish between two isomers favouring preferential transport of only one isomer in absence of reaction. In this paper the current development of chiral membrane processes will be discussed.

• Korean Chemical Engineering Research
• /
• v.48 no.4
• /
• pp.534-539
• /
• 2010

The adsorptive removal of organic sulfur compounds including tert-butylmercaptane(TBM), tetrahydrothiophene(THT) and dimethylsulfide(DMS) in methane was investigated over NaY and copper-exchanged NaY(CuNaY) zeolites at 303 K and atmospheric pressure. In the ternary adsorption system, the preferential adsorption of THT over other sulfur compounds on NaY and the concurrent adsorption of all sulfur compounds on CuNaY were achieved, which could be explained by the breakthrough curve, the temperature-programmed desorption, and the apparent activation energy for desorption. The sulfur uptake capacity of CuNaY(2.90~3.20 mmol/g) was much higher than that of NaY(0.70~0.90 mmol/g). A comparative study indicated that the $Cu^{1+}$ sites and acidity of CuNaY were probably responsible for the strong interaction with sulfur atom and high sulfur uptake abilities.