• 소성∙가공
• /
• 제10권7호
• /
• pp.579-583
• /
• 2001

Shape changes of a workpiece in an Eulerian Finite Element analysis for the steady state, three-roll-stand shape rolling are modelled. Although an Eulerian analysis has many advantages for the steady state rolling problems, it necessitates an assumption about the unknown shape of the control volume. In almost all cases, the assumed control volume does not match the final shape and the control volume should be updated. This update can be accomplished by performing a free surface correction. The final shape of a material point, which has a spherical shape at the inlet, can be also predicted by integrating a deformation gradient along a stream line. Analyses of three-roll-stand shape rolling are performed and the results are discussed in detail.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.328-331
• /
• 2001

Shape changes of a workpiece in an Eulerian Finite Element analysis for the steady state. three-roll-stand shape rolling are modelled. Although an Eulerian analysis has many advantages for the steady state rolling problems, it necessitates an assumption about the unknown shape of the control volume. In almost all cases. the assumed control volume does not match the final shape and the control volume should be updated. This update can be accomplished by performing a free surface correction. The final shape of a material point, which has a spherical shape at the inlet, can be also predicted by integrating a deformation gradient along a stream line. Analyses of three-roll-stand shape rolling is in detail examined.

• 소성∙가공
• /
• 제32권6호
• /
• pp.352-359
• /
• 2023

Recently, independent suspension systems have been applied not only to passenger cars but also to large commercial vehicles. Therefore, the need for research to domestically produce such independent suspensions for large commercial vehicles is gradually increasing. In this paper, we conducted research on the manufacturing technology of the relay lever, which are integral components of independent suspension systems for large commercial vehicles. Our goal was to reduce the flash volume generated during the forging process. The shape variables of the initial billet were adjusted to find proper forming conditions that could minimize flash volume while performing product forming smoothly. Shape variables were set as input variables and the flash volume was set as an output variable, and simulations were carried out to analytically predict the volume of the flash area for each variable condition. Based on the data obtained through numerical simulations, a regression model and an artificial neural network model were used to develop a prediction model that can easily predict the flash volume for variable conditions. For the corresponding prediction model, a goodness of-fit test was performed to confirm a high level of fit. By comparing and analyzing the two prediction models, the high level of fit of the ANN model was confirmed.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제7권1호
• /
• pp.31-43
• /
• 2007

The function of O-ring seals is to prevent leakage during the service life of the components in which they are installed. The life prediction of O-ring is very important at various industry fields. Generally, to evaluated the long-term performance of O-ring in severe environments has applied a life prediction technique based on accelerated life test (ALT). In this work, Accelerated thermal aging test(l20, 130, 140, $150^{\circ}C$) of O-ring was applied for life prediction of O-ring. The property changes after thermal aging test was measured using TGA, DSC, FT - IR, Video Microscope and SEM. Shape parameter and life prediction were obtained using MINITAB program.

• International Journal of Concrete Structures and Materials
• /
• 제2권1호
• /
• pp.57-62
• /
• 2008

When the yield line theory is used to estimate the ultimate strength of a concrete barrier, it is of primary importance that the correct assumption is made for the failure mode of the barrier. In this study, a static test was performed on two full-scale concrete barrier specimens of Korean standard shape that simulate the actual behavior of a longitudinally continuous barrier. This was conducted in order to verify the failure mode presented in the AASHTO LRFD specification. The resulting shape of the yield lines differed from that presented in AASHTO when subjected to an equivalent crash load. Furthermore, the ultimate strengths of the specimens were lower than the theoretical prediction. The main causes of these differences can be attributed to the characteristics of the barrier shape and to a number of limitations associated with the classical yield line theory. Therefore, a revised failure mode with corresponding prediction equations of the strength were proposed based on the yield lines observed in the test. As a result, a strength that was more comparable to that of the test could be obtained. The proposed procedure can be used to establish more realistic test levels for barriers that have a similar shape.

• 한국음향학회:학술대회논문집
• /
• 한국음향학회 2004년도 추계학술발표대회논문집 제23권 2호
• /
• pp.191-194
• /
• 2004

This study Is an measurement and prediction of transmission loss through dash panel with multi-path in a vehicle. Measurement results of transmission loss are decided by sound power measured using the sound intensity method under locating a sound source in the anechoic room and reverberant room, respectively. Prediction one is decided by multi-path analysis of dash panel composed by a various part of materials and complicated shape. Finally, two results show a great agreement between measured and predicted transmission loss.

• 대한기계학회논문집A
• /
• 제26권4호
• /
• pp.644-652
• /
• 2002

Increasing demands for Electric Resistance Welded pipes of high quality with thick wall require c lose investigations in edge deformation by slitting, strip deformation during break down farming, and difference of circumferential length. In order to obtain good quality of a welding zone, it is necessary to predict the edge shape of the initial strip. The modeling of the multi-pass thick tube roll forming process with rigid plastic finite element method ultra the edge shape prediction of an initial strip with 2nd-degree polynomial regression method are presented. Edge shapes of initial strip have been analyzed by the finite element method and designed by the regression method to satisfy the requirements in target fin pass. It is concluded that the proposed edge design method results in optimal edge shapes sat string the design requirements.

• 한국정밀공학회지
• /
• 제29권12호
• /
• pp.1368-1375
• /
• 2012

In this paper, a method for prediction of spread is proposed to design proper roll profile taking into account spread in shape rolling of angle bar. The effect of the process variables on spread, such as draught ratio, bending angle and aspect ratio, is analyzed by FE-analysis and response surface method (RSM). Roll profiles for equal angle bar are designed with the spread predicted by the regression equation. Effectiveness of the designed roll profiles are verified by FE-analysis in which the flange length, strain distribution, mean strain and roll torque are compared with those by Geuze. Finally, the proposed method is applied to the design of roll profile for unequal angle bar. As a result, the final product can be obtained within the allowable tolerance of ${\pm}0.5mm$ in length. Therefore, it is found that the prediction of spread can improve the efficiency of design roll profile in shape rolling of angle bar.

• 대한기계학회논문집
• /
• 제14권3호
• /
• pp.617-623
• /
• 1990

본 연구에서는 표면방향과 깊이 방향으로 표면균열의 피로성장률이 다르게 나 타나고 있는 경우의 표면균열 형상변화를 표면균열의 균열 열림을 고려하여 해석할 수 있는 식이 수정 제안되었으며, 압력용기 소재에서 측정된 표면균열의 형상변화와 본 연구에서 제안된 형상 변화식에 의한 예측과 비교 분석하였다. 또한 균열 성장과 형 상변화를 평균 응력강도계수에 대해 분석하였고 다른 표면균열 형상 변화식들에 의한 표면균열 형상변화해석이 같이 비교 검토되었다.

• 소성∙가공
• /
• 제4권4호
• /
• pp.375-389
• /
• 1995

In H shape rolling, accurate predictions of deformation and temperature distribution in a billet are quite important because they are the main factors in determining roll calibers and roll pass schedules. Many researches have been performed to achieve the predictions, but most of them are limited to single pass or isothermal assumptions. In the present investigation, it is attempted to develop a method to predict the deformation and temperature distributions which is applicable to a complete rolling process that usually consists of several rollings under different rolls for a period of time. The method works by coupling two analyses : one is an approximate analysis for temperature distribution prediction and the other is the slab-FEM hybrid analysis for deformation prediction. The method is applied to analyze a "H" shape rolling process consisting of nine passes under four different rolls. In the present paper, basic ideas of the method are presented. Also, shapes of cross sections, strain and temperature distributions, roll separating force and roll torque predicted by the method are discussed.