• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1349-1355
• /
• 1990

By examining the fatigue deformation properties of 12% Cr rotor steel which has been proved to have high fatigue and creep rupture strength around 600deg. C, authors reviewed major fatigue life prediction models such as Manson, Langer and Morrow equations, and following results were obtained. (1) A simple life prediction model for 12% Cr rotor steel was obtained as follows : DELTA..epsilon.$_{t}$ =2.18+.sigma.$_{u}$ /E+ $N^{-0.065}$+ $e^{0.6}$ $N^{-0.025}$ This equation shows that fatigue life, N, can be easily determined when total strain range, DELTA..epsilon.$_{t}$ and ultimate tensile strength, .sigma.$_{u}$ are known by simple tension test on the given test conditions. (2) Life prediction equation with equivalent maximum stress, DELTA..sigma./2, corresponding maximum strain in one cycle at room temperature is as follows: DELTA..sigma./w=-7.01logN+96.69+96.69

• Membrane Journal
• /
• v.24 no.6
• /
• pp.484-490
• /
• 2014

To find out the feasibility of the separating/enriching esters from aqueous solution using FASs (Fluoloalkyl-silanes-coupling agent)-surface modified hydrophobic membrane, the solubility parameter of FASs was obtained and compared with those of esters and water. The value of the solubility parameter of FASs (${\delta}_t=16.9$) was almost same with those of esters (ethyl acetate ${\delta}_t=18.1$, propyl acetate ${\delta}_t=18.0$, ethyl propionate ${\delta}_t=17.9$, butyl acetate ${\delta}_t=17.4$, ethyl butyrate ${\delta}_t=17.0$). However, the calculated value of the solubility parameter of water was ${\delta}_t=47.8$, which was far from the value of the solubility parameter of FASs (${\delta}_t=16.9$). This means that the FASs-modified membrane has a much higher affinity to esters than water. The experimental results of permeation flux of esters used in this study showed that the order of permeation flux predicted by the solubility parameter was almost coincide with experimental results. It might be concluded that the solubility parameter may be applicable for a separating/enriching flavors from aqueous natural-flavor solution, in which esters are main components of natural flavors.

• Journal of the Korean Society for Heat Treatment
• /
• v.2 no.4
• /
• pp.19-26
• /
• 1989

Fundmental fatigue crack propagation tests with C-T type specimens were conducted at various load ratios (R) such as 0.1, 0.3 and 0.5 in T6 and Thermomechanically treated (TMT) conditions of 7039 Al alloy. Better mechanical properties from monotonic test as well as fatigue crack propagation were obtained by TMT process owing to uniform distribution of fine microstructures and non-existence of precipitation free zone (PFZ). Through the measurement of Kop and ${\Delta}K$ at various R the concept of effective stress intensity factor range ratio, U was reviewed to asses the load ratio effect on fatigue crack propagation. A relationship between U and variables such as ${\Delta}K$ and R was obtained empirically. This may enable us to predict ${\Delta}K_{eff}$ that is of critical importance for prediction of fatigue crack propagation rate.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.208-213
• /
• 2004

Methods for estimation of the effective stress intensity factor range (${\Delta}K_{eff}$) are evaluated for narrow and wide band random loading crack growth test data of 2024-T351 aluminum alloy. Three methods of determining $K_{op}$, visual measurement, ASTM offset compliance method, and the neural network method proposed by Kang and Song, and three methods of estimating ${\Delta}K_{eff}$, conventional, the 2/PI0 and 2/PI methods proposed by Donald and Paris, are compared in a quantitative manner by using the results of fatigue crack growth life prediction under random loading. For all $K_{op}$ determination methods discussed, the 2/PI0 and 2/PI methods of estimating ${\Delta}K_{eff}$ provide better results than conventional method for narrow and wide band random loading data.

• Journal of Biomedical Engineering Research
• /
• v.28 no.2
• /
• pp.287-293
• /
• 2007

The researchers have studied for a long time about the depth of anesthesia but they don't make criteria for the depth of anesthesia. Anesthetists can't make a prediction about patient's reaction. Therefore, patients have potential risk such as poisonous side effect, late-awake, early-awake and strain reaction. In this study, the distributed characteristics on the bispectrum and bicoherence, the type of nonlinear signal processing, as a result of the coupling of EEG were presented according to depth of anesthesia. These results were consistent with a trend of delta ratio that the index of evaluation for the depth of anesthesia. The higher-order spectrum (HOS), the bispectrum and bicoherence, gives the useful information about depth of anaesthesia than other indexes.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.9
• /
• pp.1605-1614
• /
• 1992

The effects of % overload (% O.L), baseline stress intensity factor range (.DELTA. $K_{b}$) and dimension-less crack depth (a/W) are examined for the retardation behaviors after a single overload and high-low block loads in 7075-T73 aluminum alloy. And wheeler model, which is one of the fatigue life prediction models, is modified to predict retardation life using these test results. The retardation cycles( $N_{d}$) increased with a decrease in a/W and an increase in % O.L. and (.DELTA. $K_{b}$) These effects are more severe after high-low block loads than single overload. In the case of single overload, the main mechanisms of the retardation are the crack closure and the relaxation of K due to crack branching. But in the case of high-low block loads, that of the main mechanism is the crack closure caused by the accumulated compressive residual stree at the crack tip, which is related with the contact of fracture surfaces. Test results were multiple regression analyzed and got regressed shaping correction factors, (n)$_{REG}$, as function of %O.L., a/W and (.DELTA. $K_{b}$) Wheeler model is modified by using these (n)$_{REG}$. The number of delay cycles calculated by modified Wheeler model were in good agreement with the test results of this study.y.udy.y.y.y.

• Journal of Astronomy and Space Sciences
• /
• v.26 no.4
• /
• pp.425-438
• /
• 2009

We reevaluate the Burton equation (Burton et al. 1975) of predicting Dst index using high quality hourly solar wind data supplied by the ACE satellite for the period from 1998 to 2006. Sixty magnetic storms with monotonously decreasing main phase are selected. In order to determine the injection term (Q) and the decay time ($\tau$) of the equation, we examine the relationships between $Dst^*$ and $VS_s$, ${\Delta}Dst^*$ and $VS_s$, and ${\Delta}Dst^*$ and $Dst^*$ during the magnetic storms. For this analysis, we take into account one hour of the propagation time from the ACE satellite to the magnetopause, and a half hour of the response time of the magnetosphere/ring current to he solar wind forcing. The injection term is found to be $Q(nT/h)\;=\;-3.56VS_s$ for $VS_s$ > 0.5mV/m and Q(nT=h) = 0 for $VB_s\;{\leq}\;0.5mV/m$. The $\tau$ (hour) is estimated as $0.060Dst^*\;+\;16.65$ for $Dst^*$ > -175nT and 6.15 hours for $Dst^*\;{\leq}\;-175nT$. Based on these empirical relationships, we predict the 60 magnetic storms and find that the correlation coefficient between the observed and predicted $Dst^*$ is 0.88. To evaluate the performance of our prediction scheme, the 60 magnetic storms are predicted again using the models by Burton et al. (1975) and O'Brien & McPherron (2000a). The correlation coefficients thus obtained are 0.85, the same value for both of the two models. In this respect, our model is slightly improved over the other two models as far as the correlation coefficients is concerned. Particularly our model does a better job than the other two models in predicting intense magnetic storms ($Dst^*\;{< \atop \sim}\;-200nT$).

• IEMEK Journal of Embedded Systems and Applications
• /
• v.18 no.1
• /
• pp.1-7
• /
• 2023

In this paper, we implement a lossless compression technique for time-series data generated by IoT (Internet of Things) devices to reduce the disk spaces. The proposed compression technique reduces the size of the encoded data by selectively applying CNN (Convolutional Neural Networks) or Delta encoding depending on the situation in the Forecasting algorithm that performs prediction on time series data. In addition, the proposed technique sequentially performs zigzag encoding, splitting, and bit packing to increase the compression ratio. We showed that the proposed compression method has a compression ratio of up to 1.60 for the original data.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.6
• /
• pp.1529-1540
• /
• 1993

The quenching of steels by water is one of the imprtant problems in the applications of heat treatment, but the fundamental researches by way of theoretical approaches have not been satisfactorily improbed yet. This study aimed at measuring the exact subcooled transient boiling curve for cylindrical specimens and at conducting the analytical researches into the prediction of cooling curves, including the latent heat of phase transformation of steel. Experiments of quenching were made with cylindrical specimens of carbon steel S45C of diameters from 12 to 30 mm and with Cu specimens of 12 mm diameter respectively. The internal temperature of specimens during the quenching process was measured by C-A sheathed thermocouple. The heat fluxes were numerically calculated by the numerical method of inverse heat conduction problem, using the measured inner temperature of specimen as a boundary condition. In case of ${\Delta}T_{sub}=80K$, $q_{s}$ is as follows $q_{s}=2.02{\times}10^{5}{\Delta}T_{set}^{0.05}:{\Delta}T_{set}\le500K.$ And the numerical analysis of unsteady heat conduction during the quenching process was made and the cooling curves were calculated by TDMA method.

• Proceedings of the Korea Society for Simulation Conference
• /
• 2000.04a
• /
• pp.25-29
• /
• 2000

핸드오프 영역내에 정해진 RSS(Radio signal strength)에서 핸드오프를 시행하는 기존의 정적 핸드오프방식은 셀룰러 네트워크에서 제어신호가 증가하여 전송지연을 유발한다. 그러므로 핸드오프 수를 줄이는 방안으로 SPPQ(Signal Prediction Priority Queuing)에 기반한 동적 핸드오프를 제안한다.SPPQ는 RSS에 근거하여 선형적으로 핸드오프의 가능성을 예측한 후, 핸드오프 순서를 결정하는 알고리즘이다. 이 때 실제 속도와 호의 위치 분포는 일정하다고 가정하고 RSS에 대한 $\Delta$RSS(신호 세기의 증감)을 이용한다. SPPQ는 핸드오프 결정을 위해 선형적으로 RSS를 예측하며, 시간 구간에서 구한 시그널 평균을 사용한다. 그리고 두 개의 가장 최근 평균 RSS 측정값에 의해 표현되는 선형 방정식이 시간 축과 만나는 교차점을 핸드오프 예상시점으로 결정한다. 이때 각 핸드오프 후보 단말들의 threshold는 다르게 줄 수 있으며 그에 따라 우선순위를 결정한다. 이 우선순위를 기본으로 하여, 핑퐁효과로 인한 불필요한 핸드오프를 줄일 수 있도록 표본화 시간 $\Delta$t만큼 핸드오프를 낮춰 SPPQ의 성능을 높인다.