• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.315-316
• /
• 2006

A new cleaning robot system for live-line tension insulator string was developed to prevent an insulator failure, which can have severe effects on national security as well as national industry and economy. The robot moves along the insulator string using the clamps installed on its two moving frames. Especially, unlike the existing cleaning robots using jets of water or water/air, the robot system adopts dry cleaning method using a rotating brush and a circular motion guide. This robot system has control architecture consisting of a master control unit and two slave control units. We confirmed its effectiveness through experiments.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.6
• /
• pp.81-89
• /
• 2009

Dancer systems are typical equipment for attenuation of tension disturbances. Lately, demands for high speed roll-to-roll machines are rising but it is prior to attenuate the tension variation on the web entering into the printing zone to achieve the speed increment. Maintaining a constant tension before the first printing cylinder is the key of high speed, high quality printing. Dancer has been researched in two ways, whether it is controlled or not. The first one is active dancer and the other one is passive dancer. In the active dancer, a position of idle roll of dancer is measured and the roll is moved by external hydraulic cylinder to control tension disturbances. While the passive one composed with spring, damper and idle roll has no external actuator to position the idle roll. The tension disturbance causes movement of dancer roll and the displacement of the roll regulates the tension variation. On the other hand a composite type of dancer is applied for roll-to-roll printing machines. It has same apparatus as passive dancer. The displacement of roll is measured and front(or rear) driven roller is controlled to position the roll. In this paper, it is presented an analysis of pendulum dancer including position feedback PI control and logic for PI gain tuning in roll-to-roll machines. Pole-zero map and root locus with varying system parameters gives a design method for control of the dancer.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1144-1149
• /
• 2008

Converting technology has developed to print information for the decades. Recently, this technology (like gravure, gravure-offset) is rising as an alternative way for mass production of printed electronics such as RFID, solar cell. For the width of printing line is under 10 microns, registration error should be minimized less than several microns. Tension disturbance is main cause of registration error and this should be minimized before the substrate is transported into printing zone. With PI controller, it is possible to suppress the disturbance within 2% of operating tension. But register error appears more than 10 micron using PIcontroller considering noise. So LQG controller is needed as an alternative control method. In this paper, the comparision of PI and LQG controller in the converting machine including measured noise and tension disturbance is presented. It is shown that the LQG controller is more suitable for precision tension control in printed electronics.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1450-1454
• /
• 2005

In this paper, the control strategy of the tension and speed based a prototype bio-wrap winding machine is developed. The decentralized control strategy using PID control algorithm applied for each subsystem is proposed to control the each system's desired outputs, because the tension of each subsystem effects that of next roll system. The computer simulations and the experiment results are presented to show that the proposed control scheme is feasible for a prototype bio-wrap winding machine.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.541-545
• /
• 1996

In this paper, The performance and functions of automatic flatness control system installed on the 4 hi-reversing mill and has been investigated under actualconditions. A new automatic flatness control system incorporates a measuring roll for measurement and correction calculations, hydraulic roll benders, selective roll cooling, and a programmable controller for interface and data logging. The test results are as following. The more the exit steel strip thickness is thick, the smaller the I value, and the more it is thin, the larger the I value. And, a complex distribution of strip tension was controlled, for example, not only a quarter buckle but also a simple center wave and edge wave. Because the tension deviation is larger at acceleration speed and deceleration speed than steady speed, so automatic flatness control system of contact type is better to adopt over 450 m/min, automatic flatness control system reduces rapidly large flatness deviation. The maximum I value of strip has been decreased to 13 I, and defects caused by poor flatness have been drastically decreased. And coolant temperature for work roll cooling system on the automatic flatness control system is better to adopt about 50-55 .deg. C.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.963-968
• /
• 2003

The continuous process systems usually consists of various components: driven rollers. idle rolls, load-cell and so on. Even a simple fault in a single component in the line may cause a catastrophic damage on the final products. Therefore it is absolutely necessary to diagnosis the components of the continuous systems. In this paper, an adaptive eccentricity compensation method is presented. And a new diagnosis method for transverse roll shape defects on rolling process is developed. The new method was induced from analyzing the rolling mechanism by using rolling force model, tension model, Hitchcock's equation, and measured delivery thickness of materials etc. Computer simulation results also show that the proposed diagnosis methods is very effective in the diagnosis of 3-D roll shape

• Journal of the Korean Society for Precision Engineering
• /
• v.34 no.3
• /
• pp.167-172
• /
• 2017

This study proposes a method for identifying correlations between tension and drop height for sessile droplets in a roll-to-roll processing system. The effect of tension and drop height on the contact angle of a sessile droplet is presented. Design of experiment (DOE) methodology and statistical analysis are used to define a correlation between the process parameters. The contact angle is decreased while increasing tension and drop height. The influence of the tension is less significant on the contact angle compared with the effect of the drop height. However, tension should be considered as a major parameter because it is not easy to fix with roll eccentricity and compensating speed of the driven roll. The results of this study show that the effect of tension on the contact angle of a sessile droplet is more important than drop height because the drop height is fixed when the process systems are determined.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.10a
• /
• pp.193-194
• /
• 2009

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2007.06a
• /
• pp.439-440
• /
• 2007

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.5
• /
• pp.66-74
• /
• 1994

A loop-shaping LQ controller is synthesized for tandem cold mills. And a new loop- shaping technique is suggested for LQ controller design. The suggested loop-shaping LQ control system is compared with the standard loop-shaping LQ control system. The simulation results show that the theickness and interstand tension control accuracy of tandem cold mills can be improved by the compensated loop-shaping LQ controller.