• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1381-1384
• /
• 2005

In these days, the piezoresistive material has been applied to various sensors in order to measure the change of physical quantities. But the relationship between the sensitivity of a sensor and the position and size of piezoresistor has rarely been studied. Therefore, this paper was focused on the distribution of the resistance change ratio on the diaphragm and bridge surface where piezoresistor would be formed, and proposed the proper size and position of piezoresistor with which the sensitivity of sensor was increased. As the width of mass and boss was increased, the distance between piezoresistors was closed and the maximum value of resistance change ratio was decreased by the increase of the structure stiffness. And according to the increment of seismic mass size, the value of resistance change ratio is decreased by increase of the structure stiffness. Y directional piezoresistor is formed in the position of $100\mu{m}\;apart\;from\;cantilever\;edge\;and\;length\;of\;that\;is\;800\mu{m}$.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.369-372
• /
• 2002

In this research, a vision system for detecting tool breakage which is hardly detected by such indirect in-process measurement method as acoustic emission, cutting torque and motor current was developed and embedded into a PC-NC system. The vision system consists of CMOS image sensors, a slit beam laser generator and an image grabber board. Slit beam laser was emitted on the tool surface to separate the tool geometry well from the various obstacles surrounding the tool. An image of tool is captured through two steps of signal processing, that is, median filtering and thresholding and then the tool is estimated normal or broken by use of change of the centroid of the captured image. An air curtain made by the jetting high-pressure air in front of the lens was devised to prevent the vision system from being contaminated by scattered coolant, cutting chips in cutting process. To embed the vision system to a Siemens PC-NC controller 840D NC, an HMI(Human Machine Interface) program was developed under the Windows 95 operating system of MMC103. The developed HMI is placed in a sub window of the main window of 840D and this program can be activated or deactivated either by a soft key on the operating panel or M codes in the NC part program. As the tool breakage is detected, the HMI program emit a command for automatic tool change or send alarm to the NC kernel. Evaluation test in a high speed tapping center showed the developed system was successful in detection of the small-radius tool breakage.

• 소성∙가공
• /
• 제21권3호
• /
• pp.179-185
• /
• 2012

In this paper, it is proposed to produce high precision screws with a diameter of $800{\mu}m$ and a thread pitch of $200{\mu}m$ ($M0.8{\times}P0.2$) by means of a cold thread rolling process. In this part II of the study, the focus is on the production and reliability testing of the prototype $M0.8{\times}P0.2$ micro-screw. Designs for two flat dies were developed with the aid of the literature and previous studies. Process parameters during the cold thread rolling process were established through FE simulations. The simulation results showed that the threads of the micro-screw are completely formed through the rolling process. Prototype $M0.8{\times}P0.2$ micro-screw were fabricated with a high precision thread rolling machine. In order to verify the simulation results, the deformed shape and dimensions obtained from the experiment were compared with those from the simulations. Hardness and failure torque of the fabricated micro-screw were also measured. The values obtained indicate that the CAE based process design used in this paper is very appropriate for the thread rolling of micro-sized screws.

• 한국정밀공학회지
• /
• 제19권5호
• /
• pp.133-138
• /
• 2002

The technique of high speed machining is widely studied in machining fields, because the high efficiency and accuracy in machining can be obtained in high speed machining. Unfortunately the development of tool fur high speed machining in not close behind that of machine tool. In this study, 10 types flat endmill is prepared for obtaining data according to tool shape. Especially, we concentrated in helix angle, number of cutting edge and rake angle. Cutting condition is selected for several experiments and measuring cutting farce, tool life, tool wear and chip shape according to cutting length. 3-axis cutting farces are acquired from the tool dynamometer with high natural frequency, as the conventional tool dynamometer (9257B, Kistler) has cannot measure the state of high frequency force. Particularly, we found out that the axial cutting force waveform has a good relation with tool wear features. And flow is interrupted at the beginning of cutting by the decrease of rake angle. By above results. it is suggested the endmill tool with 45$^{\circ}$helix angle, 6 cutting edge and -15$^{\circ}$rake angle is suitable for high speed machining.

• 한국정밀공학회지
• /
• 제27권11호
• /
• pp.98-105
• /
• 2010

In this paper, double ball-bar is used to estimate the geometric errors of a rotary table, which includes one-axial motion, two-radial motions and two-tilt motions, except the angular positioning error. To simplify the measurement procedures, three measurement steps have been designed and developed. At each measurement step, one end of the double ball-bar is fixed at the nose of spindle and the other end is located on the rotary table. And specific circular test path is planned to keep the distance between two balls as constant at ideal case. The relationship including the geometric errors of a rotary table and the measured distance between two balls which is distorted by the geometric errors is defined by using ball-bar equation. Each geometric error is modeled as $4^{th}$ order polynomial considering $C^1$-continuity. Finally the coefficients of polynomial are calculated by least-square method. Simulation is done to check the validation of the suggested method considering set-up errors and measurement noise. Suggested method is applied to estimate geometric errors of a rotary table of a 5-axis machine tool.

• 대한기계학회논문집 C: 기술과 교육
• /
• 제1권1호
• /
• pp.13-19
• /
• 2013

$F{\theta}$ 렌즈는 레이저 프린터의 LSU(Laser Scanning Unit)의 중요 부품으로서 $F{\theta}$ 렌즈를 통과한 주사빔의 상 위치는 주사빔의 렌즈 입사각에 비례한다. 본 논문에서는 당사에서 개발한 A4 사이즈용 $F{\theta}$ 렌즈를 설계, 제작하고 보정하는 과정을 소개하였다. 렌즈 개발에서 광학설계는 Zemax를 사용하였고 주사빔의 주주사방향 및 부주사방향의 왜곡을 최소화 하기 위하여 렌즈면은 특수한 토릭면으로 하였다. 렌즈 금형은 1nm 의 분해능을 갖는 초정밀 가공기로 제작하였다. 렌즈 사출 후 성능을 평가하고 측정값과 설계값의 차이를 바탕으로 설계보정식을 유도하여 렌즈 금형을 수정하였다. 금형 수정 후 사출렌즈의 재측정 결과 초기 설계값에 가까운 성능을 확인하였다.

• 한국정밀공학회지
• /
• 제16권2호통권95호
• /
• pp.145-152
• /
• 1999

This paper presents the principle and experimental results of a non-contact surface roughness measurement by means of screen projected pattern of lase beam reflected from a polished surface. In the reflected laser beam pattern especially from a fine surface like ground or polished one, light intensity varies from the center fo the image to its boundary as the Gaussian distribution. The standard deviation of a light intensity distribution is assumed to be a good non-contact estimator for measuring the surface roughnes, because the light reflectivity is known to be well related with the surface roughness. This method doesn't need to discriminate between the specularly reflected light and the diffusely reflected one, whereas the scattered laser intensity method must do. Nor it needs to adjust the change of light intensity caused by environmental lights or specimen materials. Reflected laser beam pattern narrowly spreads out in the vertical direction to tiny scratches on the polished surface due to abrasives. The deeper the scratch the more the dispersion, which means the rougher surface. The standard deviation of the pattern is nearly in proportion to the surface roughness. Measurement errors by this method are shown to be below 10 percent compared with those obtained by a common contact method. The inclination of measuring unit from the normal axis causes the measurement errors up to 10 percent for an angle of 4 degree. Therefore the proposed method can be used as an on-the-machine quick roughness estimator within 10 percent measurement error.

• 한국산학기술학회논문지
• /
• 제1권2호
• /
• pp.1-8
• /
• 2000

본 연구에서는 상용 순수 티타늄 소재를 사용하여 안경테를 레이저 빔 용접으로 제조하기 위하여 광섬유로 전송되는 가변 펄스곡 80 ㎲-10 ms. 최대 평균출력 200 W, 첨두출력 12 kW와 최대 펄스에너지 50J성능의 초정밀 Nd:YAG 레이저 용접장치를 설계 제작하고 이 장치를 사용하여 안경테 제조를 위한 최적 용접조건을 선정하기 위한 실험을 수행하였다. 안경테를 위한 T이음 및 맞대기 이음형상을 용접할 때 평균출력, 광섬유 형태, 초점위치 등에서 용입상태와 용접결함을 조사하여 최적 용접조건을 선정하였고 안경테 부품 장석(temple hinge)과 다리, 톱바를 레이저 용접으로 시제품을 제작하였다.

• 한국ITS학회 논문지
• /
• 제17권5호
• /
• pp.173-187
• /
• 2018

본 논문에서는 주차장 관리 시스템의 한 부분으로 차량 계수를 위한 감시 카메라 시스템의 컴퓨터 비전과 심층 학습 기반 기법을 제안하고자 한다. You Only Look Once 버전 2 (YOLOv2) 탐지기를 적용하고 YOLOv2 기반의 심층 컨볼루션 신경망(CNN)을 다른 아키텍처와 두 가지 모델로 구성하였다. 제안 된 아키텍처의 효과를 Udacity의 자체 운전 차량 데이터 세트를 사용하여 설명하였다. 학습 및 테스트 결과, 자동차, 트럭 및 보행자 탐지 시 원래 구조(YOLOv2)의 경우 47.89%의 mAP를 나타내는 것에 비하여, 제안하는 모델의 경우 64.30 %의 mAP를 달성하여 탐지 정확도가 향상되었음을 증명하였다.

• 한국정밀공학회지
• /
• 제6권2호
• /
• pp.40-46
• /
• 1989

Recently, the researches on cutting the new material have been done for development of aerospace industrial engineering. Especially, titanium ally is well known as heat resisting, antiwear, anticorrosion and difficult-to-machine materials. Many studies on the analysis of shear angle have been done for improving productivity in cutting these materials. In case of titanium alloy, the saw-toothed type of chip which has wave surface of a triangular form, an eccentric from of a continuous type of chip that is produced in the cutting process, was checked. Nakayama supposed that a maximum shear strewss plane and the shear crack in the free surface made an angle of $45^{\circ}$ .deg. , but it's usually much larger than that. In this paper, the author analyzed the shear conditions of the cutting process in the quick-stopping device with the help SEM-photographs, and measured the hypotenuse angle directly in the photographs of the chips. In conclusion, the author tried to find the shear angle in the cutting process with the saw-toothed chip and compared it with the shear angles which can be calculated from the theories established by others. The results obtained are as follows. 1. In case of the saw-toothed chips, the equivalent cutting ratio can be calculated by using the chip thickness to two-thirds of ramp height. 2. The theory of Ernst-Merchant is not applicable to the titanium and its alloys which does not fractured in accordance with the theory of maximum shear stress. 3. When we cut the titanium alloys which produced the saw-toothed chips, the shear angle can be found with the theories of Rowe-Spick, P.K. Wright and the measurement of hypotenuse angle.